ISO TS 17242 AMD 1-2017 Quasi-static calibration procedure for belt force transducers - Amendment 1《带力传感器准静态校准程序 修改件1》.pdf
《ISO TS 17242 AMD 1-2017 Quasi-static calibration procedure for belt force transducers - Amendment 1《带力传感器准静态校准程序 修改件1》.pdf》由会员分享,可在线阅读,更多相关《ISO TS 17242 AMD 1-2017 Quasi-static calibration procedure for belt force transducers - Amendment 1《带力传感器准静态校准程序 修改件1》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、 ISO 2017 Quasi-static calibration procedure for belt force transducers AMENDMENT 1 Procdure dtalonnage quasi-statique pour capteurs defforts pour ceintures AMENDEMENT 1 Reference number ISO/TS 17242:2014/Amd.1:2017(E) First edition 2014-05-01 AMENDMENT 1 2017-04 TECHNICAL SPECIFICATION ISO/TS 17242
2、 ISO/TS 17242:2014/Amd.1:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
3、including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerl
4、and Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/TS 17242:2014/Amd.1:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n
5、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part i
6、n the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular
7、, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the possibility that some of the elements of th
8、is document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www
9、 .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as
10、 information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: w w w . i s o .org/ iso/ foreword .html. Amendment 1 to ISO/TS 17242:2014 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3
11、6, Safety and impact tests. ISO 2017 All rights reserved iii Quasi-static calibration procedure for belt force transducers AMENDMENT 1 5.2 Replace the first sentence with the following: The sensor offset should be measured under no load condition. A new belt strap shall be inserted and mounted in th
12、e fixture 8) .5.3 Replace the third sentence with the following: Only one loading sequence with one belt strap per test transducer up to a force level at least at 100 % of the transducers calibration range shall be performed within the given velocity range.5.6 Replace the last item of the list with
13、the following: non-linearity as a percentage in % of the transducers calibration range (for linear regression only).Annex B Replace the entire Annex B with the following: Annex B (normative) Evaluation method B.1 Linear regression For the software linearization a least-squares fit method applied thr
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISOTS17242AMD12017QUASISTATICCALIBRATIONPROCEDUREFORBELTFORCETRANSDUCERSAMENDMENT1 传感器 静态 校准 程序 修改 PDF

链接地址:http://www.mydoc123.com/p-1258065.html