ISO TR 16822-2016 Building environment design - List of test procedures for heating ventilating air-conditioning and domestic hot water equipment related to ene.pdf

《ISO TR 16822-2016 Building environment design - List of test procedures for heating ventilating air-conditioning and domestic hot water equipment related to ene.pdf》由会员分享，可在线阅读，更多相关《ISO TR 16822-2016 Building environment design - List of test procedures for heating ventilating air-conditioning and domestic hot water equipment related to ene.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2016 Building environment design List of test procedures for heating, ventilating, air-conditioning and domestic hot water equipment related to energy efficiency Conception de lenvironnement des btiments - Liste des procdures dessai lis lefficacit thermique pour les installations de chauffage,

2、ventilation, air conditionn et eau chaude usage domestique quipement de chauffage, de ventilation et de refroidissement Exigences relatives au rendement dnergie TECHNICAL REPORT ISO/TR 16822 Reference number ISO/TR 16822:2016(E) First edition 2016-07-01 ISO/TR 16822:2016(E)ii ISO 2016 All rights res

3、erved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an i

4、ntranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightis

5、o.org www.iso.org ISO/TR 16822:2016(E)Foreword iv Introduction v 1 Scope . 1 2 List of procedures by organization 1 3 Terms and definitions . 5 4 Mechanical equipment test procedures by equipment type 5 4.1 General . 5 4.2 Air conditioner and condensing unit test procedures 5 4.3 Electrically operat

6、ed unitary and applied heat pump test procedures . 6 4.4 Water chilling package test procedures 7 4.5 Packaged terminal and room air conditioner and heat pump test procedures 7 4.6 Furnace, duct furnace, and unit heater test procedures . 8 4.7 Boiler test procedures 8 4.8 Cooling tower and condenser

7、 test procedures . 9 4.9 Water heaters, pool heaters, and unfired storage tank test procedures . 9 4.10 Energy using auxiliary equipment 10 Bibliography .11 ISO 2016 All rights reserved iii Contents Page ISO/TR 16822:2016(E) Foreword ISO (the International Organization for Standardization) is a worl

8、dwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on

9、that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this d

10、ocument and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Direc

11、tives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the develo

12、pment of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO

13、specific terms and expressions related to conformit y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html. The committee responsible for this document is

14、 ISO/TC 205, Building environment design.iv ISO 2016 All rights reserved ISO/TR 16822:2016(E) Introduction The worlds energy resources are being consumed at a significant rate that will result in the depletion of known fossil fuel resources within the next century. Combustion of fossil fuels has con

15、tributed to the build-up of greenhouse gases in the atmosphere resulting in discernible climate change. The ill effects of climate change have been documented. It is imperative that energy be conserved. The building industry, through its use of energy, accounts for 30 % to 35 % of all fossil fuel us

16、age. Conservation of energy in buildings can result in a slowing down of fossil fuel usage and consequently the build-up of greenhouse gases. The energy efficiencies of components in HVAC systems are critical factors when determining building overall energy performance. Therefore, it is necessary to

17、 define common test methods that are to be used to determine efficiency for space heating, space cooling, and water heating equipment, in order to improve energy conservation. Space heating, space cooling, and water heating equipment are typically regulated by specifying both a measure of efficiency

18、 that the equipment must meet and a test method that must be used to determine that measure of efficiency. A technical report containing test procedures and globally relevant standards for the energy-efficiency of products is needed for the proper assessment of building energy performance. This Tech

19、nical Report will be a useful reference for standards developed by ISO/TC 205 and ISO/TC 163-ISO/TC 205. The ultimate goal of this effort is to develop a set of globally adopted HVAC equipment testing and rating standards under the auspices of ISO. This Technical Report lists existing HVAC equipment

20、 testing and rating procedures from around the world. Standards are listed in two ways, by the standards writing organization and by the type of equipment addressed in the standard. In Clause 2, procedures are listed by the organization that developed the procedure. In Clause 4, procedures are liste

21、d by the types of equipment that are covered by the procedure. Procedures are listed to aid in the development of new ISO procedures that may be globally adopted. ISO 2016 All rights reserved v Building environment design List of test procedures for heating, ventilating, air-conditioning and domesti

22、c hot water equipment related to energy efficiency 1 Scope This Technical Report lists testing and rating procedures for determining energy efficiency of heating, ventilating, and air conditioning equipment. This Technical Report is applicable to space conditioning and water heating equipment. Testi

23、ng and rating procedures are listed in two ways. 2 List of procedures by organization The following documents contain provisions which, through reference in this text, constitute provisions of this Technical Report. For dated references, subsequent amendments to, or revisions of, any of these public

24、ations do not apply. However, parties to agreements based on this Technical Report are encouraged to investigate the possibility of applying the most recent editions of the documents indicated below. For undated references, the latest edition of the document referred to and any updates applies. Memb

25、ers of ISO and IEC maintain registers of currently valid International Standards. AHRI AHRI 400 with Addendum 2 Liquid-to-Liquid Heat Exchangers AHRI 1230, Performance Rating of Variable Refrigerant Flow (VRF) Multi-split Air-Conditioning and Heat Pump Equipment AHRI 1160, Performance Rating of Heat

26、 Pump Pool Heaters AMCA AMCA 500-D-07, Laboratory Methods of Testing Dampers for Rating ANSI ANSI Z21.47, Gas-Fired Central Furnaces ANSI Z83.8, Gas Unit Heaters and Duct Furnaces AHAM ANSI AHAM RAC-1, Room Air-Conditioners ASHRAE ANSI ASHRAE 118.1, Method of Testing Commercial Gas, Electric and Oil

27、 Water Heaters ANSI ASHRAE 118.2, Method of Testing Residential Gas, Electric, and Oil Water Heaters ANSI ASHRAE 146, Method of Testing for Rating Pool Heaters ASHRAE Standard 103, Method of Testing for Annual Fuel Utilization Efficiency of Residential Central Furnaces and Boilers AHRI AHRI 210/240,

28、 Unitary Air-conditioning and Air Source Heat Pump Equipment TECHNICAL REPORT ISO/TR 16822:2016(E) ISO 2016 All rights reserved 1 ISO/TR 16822:2016(E) AHRI 310/380, Packaged Terminal Air-conditioners and Heat Pumps AHRI 340/360, Commercial and Industrial Unitary Air-conditioning and Heat Pump Equipm

29、ent AHRI 365, Commercial and Industrial Unitary Air-conditioning Condensing Equipment AHRI 390, Performance Rating of Single Packaged Vertical Air Conditioners and Heat Pumps AHRI 460, Remote Mechanical-Draft Air-Cooled Refrigerant Condensers AHRI 550/590 with Addenda through July 2002, Water Chilli

30、ng Packages Using the Vapor Compression Cycle AHRI 560, Absorption Water Chilling and Water Heating Packages CTI CTI ATC-105, Acceptance Test Code for Water Cooling Towers CTI STD-201, Standard for Certification of Water Cooling Tower Thermal Performance DOE DOE 10 CFR Part 430, Appendix N, Uniform

31、Test Method for Measuring the Energy Consumption of Furnaces EN EN 297, Atmospheric gas boiler without fan, 70 kW EN 303-1, Boilers with forced draught burners General requirements EN 303-2, Boilers with forced draught burners Atomizing oil burners EN 303-3, Gas boilers with forced draught burners A

32、ssemblies EN 303-4, Boilers with forced draught burners Oil burners 70 kW EN 303-6, Boilers with forced draught burners Oil fired combi-boilers EN 416, Single-burner gas-fired overhead radiant tube heaters for non-domestic use Part 2: Rational use of energy EN 419, Non-domestic gas-fired overhead lu

33、minous radiant heaters Part 2: Rational use of energy EN 625, Gas-fired combi-boilers EN 15035, Room-sealed (type C) oil-fired boilers EN 15456, Electrical power consumption for heat generators EN 267, Forced draught oil burners Definitions, requirements, testing, marking EN 304, Atomizing oil burne

34、rs Test code EN 303-7, Boilers with forced draught burners Gas fired boilers 1000 kW EN 656, Gas boilers, type B, 70 - 300 kW EN 13836, Gas boilers, type B, 300 - 1000 kW EN 483, Gas boilers, type C 70 kW EN 677, Gas condensing boilers 70 kW EN 15034, Condensing oil boilers 1000 kW2 ISO 2016 All rig

35、hts reserved ISO/TR 16822:2016(E) EN 13203-1, Gas-fired water heaters, performance assessment EN 13203-2, Gas fired water heaters, energy use assessment EN 12897, Water supply Specification for indirectly heated unvented (closed) storage water heaters EN 15332, Heating boilers Energetic assessment o

36、f hot water storage tanks EN 89, Gas-fired storage water heaters for the production of domestic hot water EN 26, Gas-fired instantaneous water heaters for sanitary uses production, fitted with atmospheric burners EN 12976-1, Thermal solar systems and components Factory made systems Part 1: General r

37、equirements EN 12976-2, Thermal solar systems and components Factory made systems Part 2: test methods EN 14511-1:2011, Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling Part 1: Terms and definitions EN 14511-2:2011, Air cond

38、itioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling Part 2: Test conditions EN 14511-3:2011, Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling Part 3: Test meth

39、ods EN 14511-4:2011, Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling Part 4: Requirements EN 12102:2008, Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for spac

40、e heating and cooling Measurement of airborne noise Determination of the sound power level EN 15218:2006, Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling Terms, definitions, test conditions, test methods and

41、 requirements EN 14825:2012, Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling Testing and rating at part load conditions and calculation of seasonal performance EN 15240:2007, Ventilation for buildings Energy performance o

42、f buildings Guidelines for inspection of air-conditioning systems EN 12599:2012, Ventilation for buildings Test procedures and measurement methods to hand over air conditioning and ventilation systems EN 15726:2011, Ventilation for buildings Air diffusion Measurements in the occupied zone of air-con

43、ditioned/ventilated rooms to evaluate thermal and acoustic conditions HI HI, Division of GAMA, BTS 2000, Testing Standard Method to Determine Efficiency of Commercial Space Heating Boilers ISO ISO 13256-1, Water Source Heat Pumps Testing and Rating for Performance Part 1: Water-to-Air and Brine-to-A

44、ir Heat Pumps ISO 13256-2, (1998), Water-Source Heat Pumps Testing and Rating for Performance Part 2: Water- to-Water and Brine-to-Water Heat Pumps ISO 2016 All rights reserved 3 ISO/TR 16822:2016(E) ISO 9459-3, Solar heating Domestic water heating systems Part 3: Performance test for solar plus sup

45、plementary systems ISO 5151:2010, Non-ducted air conditioners and heat pumps Testing and rating for performance ISO 13253:2011, Ducted air-conditioners and air-to-air heat pumps Testing and rating for performance ISO 15042:2011, Multiple split-system air-conditioners and air-to-air heat pumps Testin

46、g and rating for performance JIS JIS A 1400, Radiators, convectors and similar appliances Methods of performance test JIS A 4003, Warm air furnaces JIS A 4004, Radiators, convectors, and similar appliances Classification and requirements JIS A 4007, Fan convector JIS A 4008, Fancoil units JIS A 4111

47、, Solar water heater JIS A 4112, Solar collectors JIS A 4113, Solar storage tanks JIS A 4412, Air-conditioning unit for dwellings JIS B 8122, Test methods for measuring performance of cogeneration unit JIS B 8606, Testing of refrigerant compressors JIS B 8608, Refrigerating systemsTest methods Gener

48、al requirements JIS B 8609, Performance tests of mechanical draft cooling tower JIS B 8613, Water chilling unit JIS B 8615-1, Non-ducted air conditioners and heat pumps Testing and rating for performance JIS B 8615-2, Ducted air-conditioners and air-to-air heat pumps Testing and rating for performan

49、ce JIS B 8616, Package air conditioners JIS B 8621, Centrifugal water chillers JIS B 8622, Absorption refrigerating machines JIS B 8623, Testing methods of refrigerant condensing units JIS B 8625, Ice thermal storage units for air conditioning purpose Test methods JIS B 8627-1, Gas engine driven heat pump air conditioners Part 1: General requirements JIS B 8627-2, Gas engine driven heat pump air conditioners Part 2: Non-ducted gas engine driven