ISO 6182-8-2006 Fire protection - Automatic sprinkler systems - Part 8 Requirements and test methods for pre-action dry alarm valves《消防 自动喷水灭火系统 第8部分 预动干式报警阀的要求.pdf

《ISO 6182-8-2006 Fire protection - Automatic sprinkler systems - Part 8 Requirements and test methods for pre-action dry alarm valves《消防 自动喷水灭火系统 第8部分 预动干式报警阀的要求.pdf》由会员分享，可在线阅读，更多相关《ISO 6182-8-2006 Fire protection - Automatic sprinkler systems - Part 8 Requirements and test methods for pre-action dry alarm valves《消防 自动喷水灭火系统 第8部分 预动干式报警阀的要求.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 6182-8:2006(E) ISO 2006INTERNATIONAL STANDARD ISO 6182-8 First edition 2006-03-01 Fire protection Automatic sprinkler systems Part 8: Requirements and test methods for pre-action dry alarm valves Protection contre lincendie Systmes dextinction automatique du type sprinkler Part

2、ie 8: Exigences et mthodes dessai des postes de pralarme sous air ISO 6182-8:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are license

3、d to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the

4、software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to

5、it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without perm

6、ission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights rese

7、rvedISO 6182-8:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Requirements 5 5 Production testing and quality control. 13 6 Tests. 13 7 Marking 20 8 Instruction chart and trim 21 Bibliography . 22

8、ISO 6182-8:2006(E) iv ISO 2006 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each

9、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa

10、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards

11、 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of

12、 patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6182-8 was prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting, Subcommittee SC 5, Fixed firefighting systems using water. ISO 6182 consists of the following pa

13、rts, under the general title Fire protection Automatic sprinkler systems: Part 1: Requirements and test methods for sprinklers Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms Part 3: Requirements and test methods for dry pipe valves Part 4: Requirem

14、ents and test methods for quick-opening devices Part 5: Requirements and test methods for deluge valves Part 6: Requirements and test methods for check valves Part 7: Requirements and test methods for early suppression fast response (ESFR) sprinklers Part 8: Requirements and test methods for pre-act

15、ion dry alarm valves Part 9: Requirements and test methods for water mist nozzles Part 10: Requirements and test methods for domestic sprinklers Part 11: Requirements and test methods for pipe hangers Part 12: Requirements and test methods for grooved end pipe couplings Part 13: Requirements and tes

16、t methods for extended coverage sprinklers ISO 6182-8:2006(E) ISO 2006 All rights reserved v Introduction This part of ISO 6182 is one of a number of ISO International Standards prepared by ISO/TC 21 covering components for automatic sprinkler systems, including the following: a) carbon dioxide syst

17、ems (ISO 6183), b) explosion suppression systems (ISO 6184), An International Standard covering foam systems is planned. INTERNATIONAL STANDARD ISO 6182-8:2006(E) ISO 2006 All rights reserved 1 Fire protection Automatic sprinkler systems Part 8: Requirements and test methods for pre-action dry alarm

18、 valves 1 Scope This part of ISO 6182 specifies performance requirements, methods of test and marking requirements for pre-action dry alarm valves and manufacturers specified relevant trim used in non-interlock pre-action automatic fire protection systems. (See 3.24 for the principle modes of operat

19、ion of pre-action dry alarm valves.) Performance and test requirements for other auxiliary components or attachments to pre-action dry valves are not covered by this part of ISO 6182. 2 Normative references The following referenced documents are indispensable for the application of this document. Fo

20、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Designation, dimensions and tolerances ISO 37, Rubber, vulca

21、nized or thermoplastic Determination of tensile stress-strain properties ISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 8981, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs ISO 8982, Mechanical pr

22、operties of fasteners Part 2: Nuts with specified proof load values Coarse thread 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 alarm device mechanical or electrical device to sound an alarm upon operation of the valve 3.2 anti-reseat latch

23、 mechanical device that prevents the sealing assembly from returning to its closed position after operation ISO 6182-8:2006(E) 2 ISO 2006 All rights reserved3.3 automatic drain valve normally open device that automatically drains water from and vents the intermediate chamber of a valve to the atmosp

24、here when the valve is in the ready position, and limits water flow from the chamber after the valve has tripped 3.4 auxiliary pressure pressure acting against an auxiliary diaphragm or piston, taken from either the service pressure or an external source 3.5 clapper type of sealing element NOTE See

25、3.20. 3.6 corrosion-resistant material bronze, brass, Monel 1)metal, austenitic stainless steel, or equivalent, or plastic material conforming with the requirements of this document 3.7 differential ratio of service pressure to system air pressure (expressed as gauge pressures) at the trip point NOT

26、E See 3.24. 3.8 differential-type valve type of valve in which air pressure in the system acts directly and/or indirectly on the sealing assembly to maintain it in the closed position NOTE The air seat of the sealing assembly is of equal or larger diameter than the diameter of the water seat of the

27、sealing assembly, with the two separated by an intermediate chamber maintained at atmospheric pressure. 3.9 flow velocity speed of water flow through a valve, expressed as the equivalent water velocity through a pipe of the same nominal size as the valve 3.10 intermediate chamber that part of a valv

28、e which separates the air and/or water sealing assembly seating surfaces and is at atmospheric pressure when the valve is in the ready condition 3.11 leak point system air pressure for a specific service pressure at which water begins to flow from the intermediate chamber, automatic drain valve or a

29、larm connection 3.12 mechanical-type valve type of valve in which the air pressure in the system acts on the sealing assembly and linking mechanism to maintain it in the closed position 1) Monel is an example of a suitable product available commercially. This information is given for the convenience

30、 of users of this part of ISO 6182 and does not constitute an endorsement by ISO of this product. ISO 6182-8:2006(E) ISO 2006 All rights reserved 3 3.13 non-interlock pre-action system automatic fire protection system in which water is admitted to the system upon either activation of a supplemental

31、detection system or loss of system pressure in combination with failure of the detection system 3.14 pre-action system automatic fire protection system using a valve which is operated by an auxiliary means to admit water into a system of automatic sprinklers or nozzles, as shown in Figure 1 Figure 1

32、 Operational flow chart for pre-action system ISO 6182-8:2006(E) 4 ISO 2006 All rights reserved3.15 pre-action dry alarm valve valve of the check type in which air pressure in the sprinkler system prevents water from filling the system NOTE Fire detection of auxiliary means causes automatic operatio

33、n of the pre-action dry alarm valve. If there is any failure of the auxiliary means, the pre-action dry alarm valve shall operate as a dry valve (see ISO 6182-3). 3.16 priming water water used to seal a sealing assembly and prevent cementation of working parts 3.17 rated working pressure maximum ser

34、vice pressure at which a valve is intended to operate 3.18 ready condition set condition state of a valve with the sealing assembly in the closed and set position with service and system pressure applied 3.19 reinforced elastomeric element element of clapper, clapper assembly or seat seals in a comp

35、osite of an elastomeric compound with one or more other components 3.20 sealing assembly main movable sealing element (such as a clapper) of the valve which prevents the reverse flow of air and which maintains air pressure in the system piping 3.21 sealing assembly seat ring main fixed sealing eleme

36、nt of a valve which prevents the reverse flow of water and which maintains air pressure in the system piping 3.22 service pressure static water pressure at the inlet to a valve when the valve is in the ready condition 3.23 system pressure pressure at the main outlet of a valve when the valve is in t

37、he ready condition 3.24 system air pressure static air pressure in the system piping when the valve is in the ready condition 3.25 trim external equipment and pipework, excluding the main installation pipework, fitted to valve installation assembly 3.26 trip point point at which a valve operates, ad

38、mitting water into the system, measured in terms of the system air pressure at a given service pressure ISO 6182-8:2006(E) ISO 2006 All rights reserved 5 3.27 water-motor alarm hydraulically actuated device which provides a local audible alarm as a result of a flow through a valve 3.28 water-motor t

39、ransmitter hydraulically actuated device which generates an electrical current for a remote alarm as a result of operation of the valve 4 Requirements 4.1 Nominal sizes The nominal size of a valve shall be the nominal diameter of the inlet and outlet connections, i.e. the pipe size for which the con

40、nections are intended. The sizes shall be 40 mm, 50 mm, 65 mm, 80 mm, 100 mm, 125 mm, 150 mm, 200 mm, or 250 mm. The diameter of the waterway through the sealing assembly seat ring may be less than the nominal size. 4.2 Connections 4.2.1 All connections shall be designed for use at the rated working

41、 pressure of the valve. 4.2.2 The dimensions of all connections shall conform with the applicable requirements of International Standards. If International Standards are not applicable, national standards shall be permitted to be used. 4.2.3 An opening not smaller than 15 mm nominal diameter shall b

42、e provided for an alarm line connection. 4.2.4 If priming water is required to seal the downstream side of the sealing assembly, an external means shall be provided to introduce the priming water. 4.2.5 Means shall be provided to prevent water columning and to check the level of priming water (if re

43、quired). 4.2.6 Suitable means shall be provided to facilitate testing of alarms without tripping the valve. 4.2.7 Valves shall be provided with a means of sounding an alarm if water enters the downstream piping to an elevation exceeding 0,5 m above the sealing assembly unless the valve is provided w

44、ith an automatic means for drainage. 4.2.8 For differential-type valves, suitable means shall be provided to vent water from the intermediate chamber and to prevent a partial vacuum between the upstream and downstream sealing elements of the sealing assembly. 4.3 Rated working pressure 4.3.1 The rat

45、ed working pressure shall be not less than 1,2 MPa (12 bar). 4.3.2 Inlet and outlet connections may be machined for lower working pressures to match installation equipment provided the valve is marked with the lower working pressure. See 7.3 f). 4.4 Body and cover 4.4.1 The body and cover shall be m

46、ade of a material having corrosion resistance at least equivalent to cast iron. 4.4.2 Cover fasteners shall be made of steel, stainless steel, titanium, or other materials with equivalent physical and mechanical properties. ISO 6182-8:2006(E) 6 ISO 2006 All rights reserved4.4.3 If non-metallic mater

47、ials, other than gaskets, and seals or metals with a melting point less than 800 C form part of the body or cover, the valve assembly shall be subjected to a fire exposure test as specified in 6.9. Following the fire exposure test, the sealing assembly shall open freely and fully and the valve shall

48、 withstand a hydrostatic pressure test as specified in 6.7.1 without permanent deformation or failure. 4.4.4 It shall not be possible to assemble the valve with the cover plate in a position which either improperly indicates flow direction or prevents proper operation of the valve. 4.5 Strength 4.5.

49、1 An assembled valve, with the sealing assembly blocked open, shall withstand, without rupture, an internal hydrostatic pressure of four times the rated working pressure for a period of 5 min when tested as specified in 6.7.1. 4.5.2 If the test in accordance with 6.9 is not done with standard production fasteners, the supplier shall provide documentation showing that the calculated design load of any fastener, neglecting the force required to compress the gasket, shall not exceed th