ISO 11962 CORR 1-2006 Micrographics - Image mark (blip) used with 16 mm and 35 mm roll microfilm Technical Corrigendum 1《缩微照相 带16mm和35mm缩微胶卷用成象标记(雷达显示的影像) 技术勘误1.pdf

《ISO 11962 CORR 1-2006 Micrographics - Image mark (blip) used with 16 mm and 35 mm roll microfilm Technical Corrigendum 1《缩微照相 带16mm和35mm缩微胶卷用成象标记(雷达显示的影像) 技术勘误1.pdf》由会员分享，可在线阅读，更多相关《ISO 11962 CORR 1-2006 Micrographics - Image mark (blip) used with 16 mm and 35 mm roll microfilm Technical Corrigendum 1《缩微照相 带16mm和35mm缩微胶卷用成象标记(雷达显示的影像) 技术勘误1.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 37.080 Ref. No. ISO 11962:2002/Cor.1:2006(E) ISO 2006 All rights reserved Published in Switzerland INTERNATIONAL STANDARD ISO 11962:2002 TECHNICAL CORRIGENDUM 1 Published 2006-12-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATIONMicrographics Image mar

2、k (blip) used with 16 mm and 35 mm roll microfilm TECHNICAL CORRIGENDUM 1 Micrographie Repre dimage (pav optique) utilis avec des microfilms en rouleau de 16 mm et 35 mm RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO 11962:2002 was prepared by Technical Committee ISO/TC 171, Document manage

3、ment applications, Subcommittee SC 2, Application issues. Page 1, Clause 2 Replace the normative reference “ISO 6196 (all parts), Micrographics Vocabulary” with the following normative references “ISO 6196-1:1993, Micrographics Vocabulary Part 1: General terms ISO 6196-2:1993, Micrographics Vocabula

4、ry Part 2: Image positions and methods of recording ISO 6196-3:1997, Micrographics Vocabulary Part 3: Film processing ISO 6196-4:1998, Micrographics Vocabulary Part 4: Materials and packaging ISO 6196-5:1987, Micrographics Vocabulary Part 5: Quality of images, legibility, inspection ISO 11962:2002/C

5、or.1:2006(E) 2 ISO 2006 All rights reservedISO 6196-6:1992, Micrographics Vocabulary Part 6: Equipment ISO 6196-7:1992, Micrographics Vocabulary Part 7: Computer micrographics ISO 6196-8:1998, Micrographics Vocabulary Part 8: Use” Page 1, Subclause 4.1 Replace the first paragraph of subclause 4.1 wi

6、th the following text: “Image marks shall be arranged in either of the following ways (see Figure 1). In a channel along either the bottom or top edge of the microfilm. Images may be in either simplex or duplex format as defined in ISO 6196-2. Either format can be used in either the lower (A) channe

7、l or the upper (B) channel. For single channel use, the lower, channel A, is more often used. In two channels, channel A along the bottom edge of the microfilm and channel B along the top edge. Image marks start from the start of the film in channel A, run with increasing count to the end of the fil

8、m, then continue from the end of the film back to the start of the film in channel B.” Page 1, Subclause 4.2 Replace subclause 4.2 with the following subclauses: “4.2 Document image area Document images shall not extend to less than 2,16 mm from the film edge if an image mark channel is used along t

9、hat edge (see Figure 2). 4.3 Splices If the microfilm is spliced, the splice shall not alter or obscure any part of any image mark, nor result in marking that could be interpreted as an image mark by retrieval devices. For example opaque tape is not permitted.” Page 2, Figure 1 Replace Figure 1 with

10、 the following figure: ISO 11962:2002/Cor.1:2006(E) ISO 2006 All rights reserved 3a) Single channel for simplex or duplex format b) Single channel for simplex or duplex format c) Two channel for duo or duo duplex format Key 1 leading end of microfilm 2 image area Figure 1 Permissible channel locatio

11、ns ISO 11962:2002/Cor.1:2006(E) 4 ISO 2006 All rights reservedPage 3, Subclause 4.3 Renumber the existing subclause 4.3 as subclause 4.4, Position of image marks, and replace its second paragraph with the following text: “The distance from the leading edge of the image mark to the leading or trailin

12、g edge of the document image, whichever is selected as the reference edge of the document image, measured parallel to the edge of the microfilm, shall be uniform within 0,15 mm throughout the roll of microfilm.” Page 3, Subclause 4.4 Renumber the existing subclause 4.4 as subclause 4.5, Spacing. Pag

13、e 3, Clause 5 Immediately following the heading of Clause 5, insert a new subclause 5.1 with the following: “5.1 Types of image mark Image marks shall be either single size marks throughout the microfilm, or small and medium marks throughout the microfilm or small, medium and large marks throughout

14、the microfilm. The latter two options allow more sophisticated searches. Medium and large marks as a combination is not recommended.” Renumber the existing subclauses 5.1 to 5.3 as subclauses 5.2 to 5.4, respectively. Replace the text of the newly numbered subclause 5.4 with the following: “5.4 Imag

15、e mark positioning An image mark shall be positioned such that it at least covers an area that is not greater than 1,02 mm from the edge of the microfilm to not less than 1,86 mm from that edge. It shall not extend more than 2,16 mm from that edge (see Figure 2).” Page 4, Subclause 7.2.2 Replace the

16、 text of subclause 7.2.2 with the following: “7.2.2 Start codes Start codes shall comprise one or more image marks. Each mark shall be at least 8,7 mm long and preceded by a space equal to or greater than the length of a small image mark.” Page 4, Subclause 7.2.3 Replace the text of subclause 7.2.3 with the following: “7.2.3 Stop codes Stop codes shall comprise one or more image marks. Each shall be at least 8,7 mm long and preceded by a space equal to or greater than the length of a small image mark.”