ISO 10532 AMD 1-2004 Earth-moving machinery - Machine-mounted retrieval device - Performance requirements Amendment 1《土方机械 机械悬挂补偿装置 性能要求 修改件1》.pdf

《ISO 10532 AMD 1-2004 Earth-moving machinery - Machine-mounted retrieval device - Performance requirements Amendment 1《土方机械 机械悬挂补偿装置 性能要求 修改件1》.pdf》由会员分享，可在线阅读，更多相关《ISO 10532 AMD 1-2004 Earth-moving machinery - Machine-mounted retrieval device - Performance requirements Amendment 1《土方机械 机械悬挂补偿装置 性能要求 修改件1》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD IS0 10532 First edition AMENDMENT 1 1995-1 2-1 5 2004-09-01 Earth-moving machinery - Machine- mounted retrieval device - Performance requirements AMENDMENT 1 Engins de terrassement - Dispositif de remorquage mont sur lengin - Exigences de performance AMENDEMENT 1 Reference num

2、ber IS0 10532:1995/Amd.l:2004(E) IS0 2004 IS0 10532: 1995/Amd.l:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and inst

3、alled on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The IS0 Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the sofiware prod

4、ucts used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IS0 member bodies. In the unlikely event that a problem relating to it is found,

5、please inform the Central Secretariat at the address given below. O IS02004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in wr

6、iting from either IS0 at the address below or ISOs member body in the country of the requester. IS0 copyright office Case postale 56 CH-I211 Geneva 20 Tel. + 41 22 749 O1 11 Fax +41 227490947 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii O IS0 2004 -All rights reserved IS0 1053

7、2: 1995/Amd.l:2004(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a

8、 subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commissio

9、n (I EC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical c

10、ommittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS0 shall n

11、ot be held responsible for identifying any or all such patent rights. Amendment 1 to IS0 10532:1995 was prepared by Technical Committee ISOTC 127, Earth-moving machinery, Subcommittee SC 1, Test methods relating to machine performance. O IS0 2004 -All rights reserved iii IS0 10532: 1995/Amd.l:2004(E

12、) Earth-moving machinery - Machine-mounted retrieval device - Performance requirements AMENDMENT 1 Page 2, Clause 4 Add the following new subclause. “4.7 The machine operating manual shall provide instructions regarding the method of retrieving or towing the machine if the manufacturer recommends th

13、at devices such as wire ropes, chains or links be wound around structural members as a means for retrieval.” O IS0 2004 -All rights reserved 1 IS0 10532: 1995/Amd.l:2004(E) ICs 53.100 Price based on 1 page O IS0 2004 -All rights reserved 4851903 ObYb147 8Ob INTERNATIONAL STANDARD IS0 10532 First edi

14、tion 1995-1 2-1 5 Earth-moving machinery - Machine- mounted retrieval device - Performance requirements Engins de terrassement - Dispositif de remorquage mont sur lengin - Exigences de performance Reference number IS0 10532:1995(E) 4851903 Ob4b148 742 IS0 10532:1995(E) Foreword IS0 (the Internationa

15、l Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been es

16、tablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardi

17、zation. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 10532 was prepared by Technical Commit

18、tee ISO/TC 127, Earth-moving machinery, Subcommittee SC 1, Test methods relating to machine performance. Annex A of this International Standard is for information only. O IS0 1995 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form o

19、r by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case Postale 56 CH-1 21 1 Genve 20 Switzerland Printed in Switzerland ii 4853903 Ob46347 687 INTERNATIONAL STANDARD IS0 IS0

20、 10532:1995(E) Earth-moving machinery - Machine-mounted retrieval device - Performance requirements 1 Scope This International Standard defines the performance requirements of a retrieval device mounted on an earth-moving machine listed in IS0 6165. Requirements for verification testing, if needed,

21、are included. Studies have shown that the tow rope, used for retrieving a large disabled or mired earth-moving rope. This is typically the largest size that can be handled by the person connecting the tow rope to the machine. I machine is seldom larger than 40 mm diameter wire Therefore, this Intern

22、ational Standard is applicable to machine-mounted retrieval devices of capacities not exceeding lo6 N. This value corresponds to the minimum breaking force of a 40 mm diameter Group 3 wire rope with steel core as listed in IS0 2408. NOTE 1 In accordance with IS0 6750, information on the location and

23、 instructions for proper use of retrieval devices is provided in the operator manual. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were

24、 valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to in- vestigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid Internatio

25、nal Standards. IS0 6016:1982, Earth-moving machinery - Methods of measuring the masses of whole machines, their equipment and components. IS0 61 65:1987, Earth-moving machinery - Basic types - Vocabulary. IS0 9248:1992, Earth-moving machinery - Units for dimensions, performance and capacities, and t

26、heir measurement accuracies. 3 Definitions For the purposes of this International Standard, the following definitions apply. 3.1 machine-mounted retrieval device: Connector attached to a machine that provides a means to attach a tow rope, a chain, or a tow bar to a disabled or mired machine. 3.2 cap

27、acity (of a retrieval device): Value, expressed in newtons, of the force applied to a machine- mounted retrieval device that results in a stress level equal to the yield strength of the material that is used to manufacture the retrieval device. 3.3 machine mass for calculation (1 1 For tractor-scrap

28、ers and dumpers: Combined mass of the machines operating mass, as defined in IS0 6016, and the rated paymass as specified by the manufacturer. NOTE 2 This mass is the “loaded mass“. (See IS0 7132 and IS0 71 33.) (2) For all other machines: Operating mass of the machine, as defined in IS0 6016. 3.4 m

29、aximum pull angle: Angle of 20 O which is the included angle of a cone with an axis that is a horizontal line passing through the tow rope connecting point on the machine-mounted retrieval device and parallel to the longitudinal axis of the machine, but limited by interference with parts of the mach

30、ine. 1 4853903 0b4bL50 3T0 IS0 10532:1995(E) IS0 4 Requirements 4.1 The capacity, in newtons, of the machine- mounted retrieval device shall be equal to 1,5 times the machine mass for calculation (see 3.31, multiplied by the acceleration due to gravity (g) except for tractor-scrapers and bottom dump

31、ers. For these machines the capacity, in newtons, shall be equal to the machine mass for calculation multiplied by the acceleration due to gravity (gi. NOTE 3 The capacity of the retrieval device for any machine need not exceed 1 O6 N. (See Scope.) 4.2 The machine-mounted retrieval device shall with

32、stand the capacity defined in 4.1 at the maximum pull angle. 4.3 The machine-mounted retrieval device shall be made of materiais that display visible signs of deformation (yield) before failure (fracture) so that it is apparent that it has been overloaded and must be repaired or replaced. 4.4 The ma

33、chine-mounted retrieval device shall be designed to accept a wire rope sling or clevis of a size capable of withstanding the force corresponding to the capacity defined in 4.1. 4.5 If a pull-pin type retrieval device is used, provisions shall be made to retain the pin in place during use and to prev

34、ent the pin from being lost when it is not in use. 4.6 The machine-mounted retrieval device may be mounted at the front and/or rear of the machine. It shall be in a location that is easily accessible for attaching a tow rope, a chain, or a tow bar. For machines with a machine operating mass larger t

35、han IO5 kg, a second retrieval device should be provided on the same end of the machine. Each device shall conform with the requirements of this International Standard. 5 Verification 5.1 The performance requirements of the retrieval device and its supporting structure on the machine shall be verifi

36、ed by testing or by calculation. 5.2 If verified by testing, one pull at the maximum pull angle in the horizontal plane and one pull at the maximum pull angle in the vertical plane shall be made. The force applied shall correspond to the capacity defined in 4.1. Tolerances for test loads and pull an

37、gle shall be as given in IS0 9248. 2 4851903 Ob4bl.51 237 = - IS0 10532:1995(E) Annex A (informa tive) Bibliography I I IS0 2408: 1985, Steel wire ropes for general purposes - Characteristics. 12) IS0 6750:1984, Earth-moving machinery - Operation and maintenance - Format and content of manuak. 3 IS0

38、 71 32: 1990, Earth-moving machinery - Dumpers - Terminology and commercial specifications. 4) IS0 71 33: 1994, farth-moving machinery - Tractor-scrapers - Terminology and commercial specifications. 3 IS0 10532:1995( E) rn 4853903 Ob46352 173 rn ICs 53.100 Descripteurs: earth-rnoving equipment, mechanical couplings, towing attachments, specifications, performance, verification Price based on 3 pages