IEC 61988-4-2-2012 Plasma Display Panels - Part 4-2 Environmental testing methods - Panel strength《等离子体显示屏.第4-2部分 环境试验方法.面板强度》.pdf

《IEC 61988-4-2-2012 Plasma Display Panels - Part 4-2 Environmental testing methods - Panel strength《等离子体显示屏.第4-2部分 环境试验方法.面板强度》.pdf》由会员分享，可在线阅读，更多相关《IEC 61988-4-2-2012 Plasma Display Panels - Part 4-2 Environmental testing methods - Panel strength《等离子体显示屏.第4-2部分 环境试验方法.面板强度》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61988-4-2 Edition 1.0 2012-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Plasma display panels Part 4-2: Environmental testing methods Panel strength Panneaux daffichage plasma Partie 4-2: Mthodes dessais denvironnement Rsistance des panneaux IEC61988-4-2:2012 THIS PUBLICATION IS COPYRIGHT PRO

2、TECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs

3、 member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduc

4、tion rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du de

5、mandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax

6、: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publicati

7、ons The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC

8、publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publication

9、s released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known

10、 as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique

11、 Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vo

12、us assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtude

13、s,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois

14、par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulai

15、re Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61988-4-2 Edition 1.0 2012-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Plasma disp

16、lay panels Part 4-2: Environmental testing methods Panel strength Panneaux daffichage plasma Partie 4-2: Mthodes dessais denvironnement Rsistance des panneaux INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE N ICS 31.120; 31.260 PRICE CODE CODE PRIX ISBN 978-2-889

17、12-049-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication v

18、ia un distributeur agr. 2 61988-4-2 IEC:2012 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Structure of measuring equipment 6 5 Standard measuring conditions . 6 6 Measuring methods 6 6.1 Ball drop strength 6 6.1.1 Purpose . 6 6.1.2 Measuring equipment 6

19、6.1.3 Applicability . 6 6.1.4 Measurement layout 6 6.1.5 Measuring point . 8 6.1.6 Ball and drop height 8 6.1.7 Measuring procedure . 9 6.2 Partial heating strength . 9 6.2.1 Purpose . 9 6.2.2 Measuring equipment 9 6.2.3 Measuring environmental conditions 10 6.2.4 Measuring layout . 10 6.2.5 System

20、diagram . 12 6.2.6 Measuring positions . 12 6.2.7 Heating rate and maximum temperature 13 6.2.8 Measuring procedure . 13 Bibliography 14 Figure 1 Setting of PDP module (side view) . 7 Figure 2 Setting of PDP module using spacers (side view) . 7 Figure 3 Setting of PDP panel (side view) 7 Figure 4 Me

21、asuring layout of ball drop strength (side view) 8 Figure 5 Measuring points 8 Figure 6 PDP panel setting 11 Figure 7 Setting of thermal sensor (sectional view) 11 Figure 8 Set up of measuring equipment 12 Figure 9 Measuring positions . 12 Table 1 Ball and drop height . 9 61988-4-2 IEC:2012 3 INTERN

22、ATIONAL ELECTROTECHNICAL COMMISSION _ PLASMA DISPLAY PANELS Part 4-2: Environmental testing methods Panel strength FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committ

23、ees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Availabl

24、e Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organi

25、zations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical ma

26、tters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC Natio

27、nal Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, I

28、EC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itse

29、lf does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that t

30、hey have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature

31、 whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced p

32、ublications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International

33、 Standard IEC 61988-4-2 has been prepared by IEC technical committee 110: Electronic display devices. The text of this standard is based on the following documents: FDIS Report on voting 110/354/FDIS 110/369/RVD Full information on the voting for the approval of this standard can be found in the rep

34、ort on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 61988 series, published under the general title Plasma display panels, can be found on the IEC website. 4 61988-4-2 IEC:2012 Future Part

35、 4-x standards in this series will include the new title component: Environmental testing methods, as cited above. Titles of existing Part 4-x standards in this series will be updated accordingly at the time of the next edition. The committee has decided that the contents of this publication will re

36、main unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61988-4-2 IEC:2012 5 PLASMA DISPLAY PANELS Par

37、t 4-2: Environmental testing methods Panel strength 1 Scope This part of IEC 61988 defines testing methods for evaluating mechanical characteristics of plasma display modules (PDP modules) in the following areas: a) Ball drop breaking strength of panels; b) Partial heating strength of panels. 2 Norm

38、ative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

39、 applies. IEC 60068-1:1988, Environmental Testing Part 1: General and guidance IEC 61988-1, Plasma display panels Part 1: Terminology and letter symbols IEC 61988-2-1, Plasma display panels Part 2-1: Measuring methods Optical and optoelectrical IEC 61988-4, Plasma display panels Part 4: Climatic and

40、 mechanical testing methods 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60068-1 and IEC 61988-1 and the following apply. 3.1 ball drop breaking strength breaking strength against a ball drop impact measured as a breaking drop height using a ball

41、whose weight and material are previously determined 3.2 rubber heater soft and flexible sheet (generally made from thermally conductive rubber) in which electric heating element is molded Note 1 to entry: Temperature uniformity of rubber heater is obtained by the layout of heating wire in the sheet

42、and its material. 3.3 partial heating strength mechanical strength under a thermal stress caused by heating a limited area of panel 6 61988-4-2 IEC:2012 Note 1 to entry: Still images including bright small part(s) located near screen edge surrounded by dark background emulate significant partial hea

43、ting at the bright part(s). In some cases, the thermal stress breaks the panel. Luminous efficacy and heat radiation design affect the thermal stress. 4 Structure of measuring equipment The system diagrams and/or driving conditions of the measuring equipment shall comply with the structure specified

44、 in each item. 5 Standard measuring conditions Measurements shall be carried out under the standard environmental conditions defined in IEC 61988-2-1, i.e. at a temperature of 25 C 3 C, a relative humidity of 25 % to 85 % and a pressure of 86 kPa to 106 kPa. PDP modules and PDP panels to be measured

45、 shall be kept in off-state and in the environmental conditions until they reach the stable temperature. When different conditions are used, these shall be noted on the report. The standard reference atmosphere defined in IEC 61988-4, i.e. 25 C and 101,3 kPa, is applied. 6 Measuring methods 6.1 Ball

46、 drop strength 6.1.1 Purpose The purpose of this method is to measure the impact strength of screen of a PDP module using ball drop. 6.1.2 Measuring equipment The following equipment shall be used: a) ball; NOTE 1 Three kinds of smooth steel balls with the weights of 5,6 g, 8,3 g and 533 g are used.

47、 b) height scale; and c) others when used. NOTE 2 For example a drop guide, which is a straight plastic pipe, whose inner radius is larger than the radius of ball, and has side holes at the drop heights, can be used. 6.1.3 Applicability This measurement can be applied to PDP module and PDP panel. In

48、 the case that modules use directly laminated filter, the modules should be measured with the directly laminated filter. 6.1.4 Measurement layout The PDP module shall be set on a rigid table or a rigid floor with the screen upward and horizontal avoiding free movement and vibration as shown in Figur

49、e 1, or Figure 2 by using rigid spacers. In the case of a PDP panel, the panel shall be set on a measurement base with the screen upward and horizontal as shown in Figure 3, avoiding free movement and vibration. The measurement base and the cushion sheets should be the chassis and the bonding material(s)/adhesive sheets respectively, or well-defined ones. The details of the measurement base and the