GA 225-2008 REPAIR OF FIRE-RATED GYPSUM PANEL PRODUCT SYSTEMS《防火石膏板产品系统的维修》.pdf

《GA 225-2008 REPAIR OF FIRE-RATED GYPSUM PANEL PRODUCT SYSTEMS《防火石膏板产品系统的维修》.pdf》由会员分享，可在线阅读，更多相关《GA 225-2008 REPAIR OF FIRE-RATED GYPSUM PANEL PRODUCT SYSTEMS《防火石膏板产品系统的维修》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、GA-225-08 Copyright Gypsum Association 2008. All rights reserved. Printed in U.S.A. GYPSUM ASSOCIATION 810 FIRST STREET NE, #510 WASHINGTON, DC 20002 REPAIR OF FIRE-RATED GYPSUM PANEL PRODUCT SYSTEMS (GA-225-08) Fire-rated gypsum panel product systems may be damaged during the life cycle of build-in

2、gs. To maintain the required fire-rated separa-tion between occupancies or areas, damaged systems must be repaired so that they are re-stored to their original fire-resistive condition. The repair must follow procedures dictated by the severity of the damage. Small holes (such as those caused by a d

3、oor-knob) can be repaired by patching. To maintain the integrity of the surface membrane, a gypsum panel product patch must be mechanically se-cured in the diaphragm; attachment with joint compound material only is not acceptable. The patching material should be cut from type X or proprietary type X

4、 gypsum panel product of a thickness equal to the original materials so that the patching material is in the same geometric shape as, but slightly larger than, the damaged area. The damaged area is then further enlarged to match exactly the size of the patching mate-rial. Use caution when cutting or

5、 fastening into stud cavities to avoid electrical shock or water leaks. Thermal insulation, if present, must be restored. Metal runner track is secured to the inside edges of the damaged area. The patching material is screw attached to the exposed face of the runner track with fasteners a maximum of

6、 8 in. (200 mm) apart. The patch should be treated with tape and joint compound to restore appear-ance, fire resistance qualities, and acoustical performance. NOTE: Overlapping of joint tape can result in finishing problems. Several alternative proprietary clip products are available which provide m

7、echanical support for patching. Manufacturers of these products should be contacted for information. If mechanically or environmentally caused damage covers more than 100 in (700 cm) in 100 ft (10 m) of wall or ceiling area, all mate-rials in the damaged area back to the original framing must be rem

8、oved to make the repair. Framing in the area to be repaired should be in-spected and replaced if necessary without in-creasing original framing spacing. Replacement material should be cut to fill the opening and mechanically attached to the framing. Ends and edges of the board that are not backed by

9、 fram-ing materials should be supported with metal runner track. The repaired area should be fin-ished with tape and joint treatment compound as necessary. Multiple-layer systems typically require that joints be staggered between layers. Proper repair of multiple-layer systems requires that face lay

10、-ers of board be removed beyond the base layer joint so as to retain the staggered joint feature. To improve the appearance of large areas that are in structurally sound, but aesthetically unac-ceptable condition, a new layer of regular or type X gypsum board may be attached to the existing surface

11、with adhesive or mechanical fasteners without adversely affecting the fire resistance rating or acoustical performance.GA-225-08 Copyright Gypsum Association 2008. All rights reserved. Printed in U.S.A. Figure 1. Damaged Gypsum Board Figure 2. Square-Off Damaged Area Figure 3. Frame Cutout Figure 4.

12、 Apply Gypsum Board Patch Figure 5. Tape and Finish Patched Area Figure 6. Redecorate Patched Area This document may be revised or withdrawn from circulation at any time. The status of the document should be verified by the user prior to following any recommendations contained herein. To verify that you have the most current edition of the document, access the Gypsum Association website at: www.gypsum.org.