UL 60730-2-18 (ND)-2004 National Differences For UL 60730-2-18 Standard for Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements for Automaticls.pdf

《UL 60730-2-18 (ND)-2004 National Differences For UL 60730-2-18 Standard for Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements for Automaticls.pdf》由会员分享，可在线阅读，更多相关《UL 60730-2-18 (ND)-2004 National Differences For UL 60730-2-18 Standard for Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements for Automaticls.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60730-2-18Standard for Automatic Electrical Controls for Household and Similar Use; Part 2: ParticularRequirements for Automatic Electrical Water and Air Flow Sensing C

2、ontrols IncludingMechanical RequirementsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60730-2-18Standard for Automatic Electrical Controls for Household and Similar Use; Part 2: ParticularRequirements for Automatic

3、 Electrical Water and Air Flow Sensing Controls Including MechanicalRequirementsEdition: 1Edition Date: January 16, 2004This is the publication of the first edition of UL 60730-2-18 which includes the adoption of the ULnational differences to IEC 60730-2-18.This document provides a single listing of

4、 the National Differences included in the UL adoption ofthe corresponding IEC standard. Editorial differences appearing in the UL standard are notincluded in this technical compilation. The complete listing of National Differences is available inthe UL standard.The master for this standards document

5、 at ULs Northbrook Office is the official standards documentinsofar as it relates to a UL service and the compliance of a product with respect to the requirements forthat product and service, or if there are questions regarding the accuracy of this document.ULs standards documents are copyrighted by

6、 UL. Neither a printed copy of a standards document, northe electronic file for a standards document should be altered in any way. All of ULs standards documentsand all copyrights, ownerships, and rights regarding those standards documents shall remain the sole andexclusive property of UL.All rights

7、 reserved. No part of this standards document may be reproduced, stored in a retrieval system,or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, ei

8、ther expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damag

9、es arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the possibility of such damage. In no event shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form o

10、f the claim.UL reserves the right to change the format, presentation, file types and formats, delivery methods andformats, and the like of both its printed and electronic Standards documents without prior notice.Purchasers of the electronic versions of ULs standards documents agree to defend, indemn

11、ify, and holdUL harmless from and against any loss, expense, liability, damage, claim, or judgement (includingreasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing anelectronic standards document on the purchasers computer system.JANUARY 16, 2004NATIO

12、NAL DIFFERENCES FOR UL UL 60730-2-182UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULIf a single-user version electronic standards document was purchased, one copy of this standardsdocument may be stored on the hard disk of a single personal c

13、omputer, or on a single LAN file-serveror the permanent storage device of a multiple-user computer, or made available through the purchasersIntranet in such a manner that this standards document may only be accessed by one user at a time andfor which there is no possibility of multiple simultaneous,

14、 concurrent access.If a multiple-user version electronic standards document was purchased, one copy of the standardsdocument may be stored on a single LAN file-server, or on the permanent storage device of amultiple-user computer, or made available through the purchasers Intranet. The number of simu

15、ltaneous,concurrent users shall not exceed the number of users authorized.Electronic standards documents are intended for on-line use, such as for viewing the requirements of astandards document, conducting a word search, and the like. Only one copy of the standards documentmay be printed from each

16、single-user version of an electronic standards document. Only one copy of thestandards document may be printed for each authorized user of a multiple-user version of an electronicstandards document. Because of differences in the computer/software/printer setup used by UL and thoseof electronic stand

17、ards document purchasers, the printed copy obtained by a purchaser may not lookexactly like the on-line screen view or the printed standards document.An employee of an organization purchasing a UL standards document can make a copy of the page orpages being viewed for their own fair and/or practical

18、 internal use.Copyright 2004 Underwriters Laboratories Inc.JANUARY 16, 2004 NATIONAL DIFFERENCES FOR UL UL 60730-2-18 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Dif

19、ferences included in the UL adoptionof the corresponding IEC standard. Editorial national differences (those marked DE) are not included inthis technical compilation.In its IEC-based standards, UL uses the notations indicated below to identify national difference type, andthese types are additionall

20、y noted in this document. The standard may not use all types of thesedeviations.DR - These are deviations based on the National Electrical Code (NEC) and other U.S. RegulatoryRequirements.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would

21、 compromise safety for U.S. consumers and users of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are

22、 deviations based on the component standards and will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or correctionsJANUARY 16, 2004NATIONAL DIFFERENCES FOR UL UL 60730-2-184UL COPYRIGHTED MATERIA

23、L NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences1.2DV D2 Modification of 1.2:The maximum voltage is 600 V. The maximum current is unlimited.1.5DV D2 Modification of 1.5 by adding the following:The following are US National References:Creepage Di

24、stance for Electric Equipment, Insulation Coordination Including Clearancesand UL 840Fittings for Conduit and Outlet Boxes UL 514CFuseholders UL 512Fuses for Supplementary Overcurrent Protection UL 198GGrounding and Bonding Equipment UL 467Marking and Labeling Systems UL 969Metallic Outlet Boxes UL

25、514ANonmetallic Outlet Boxes, Flush-Device Boxes, and Covers UL 514CPlastic Materials for Parts in Devices and Appliances, Tests for Flammability of UL 94Polymeric Materials Fabricated Parts UL 746DPolymeric Materials Long Term Property Evaluation UL 746BPolymeric Materials Short Term Property Evalu

26、ation UL 746APolymeric Materials Use in Electrical Equipment Evaluations UL 746CJANUARY 16, 2004 NATIONAL DIFFERENCES FOR UL UL 60730-2-18 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrinted-Wiring Boards UL 796Safety-Related Software UL

27、1998Sleeving, Coated, Electrical UL 1441Switches, Special-Use UL 1054Systems of Insulating Materials General UL 1446Tape, Insulating UL 510Terminal Blocks UL 1059Terminals, Electrical Quick-Connect UL 310Transformers, Class 2 and Class 3 UL 1585Transformers, Specialty UL 506Tubing, Extruded Insulati

28、ng UL 224Wire Connectors and Soldering Lugs for Use With Copper Conductors UL 486ATable 7.2DV D2 Replacement of Table 7.2 with Table 7.2DV:JANUARY 16, 2004NATIONAL DIFFERENCES FOR UL UL 60730-2-186UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM

29、ULTable 7.2DVInformation Clause or subclause Method5 Not applicable23 Temperature limits of mounting surfaces (Ts) 6.12.2, 14.1, 17.3 D34 Not applicable38 Not applicable44 Not applicable48 Operating value(s) 2.3.11, 2.3.12, 6.4.3.10, 10,11, 14, 15.6, 17D101 Maximum fluid temperature (TL) in C 14.5.1

30、 D102 Maximum working pressure, if applicable 2.3.29, 18.101 C103 Any special environmental conditions in which thecontrol is intended to be used (other than declared intable 7.2, requirement 15)101)12.101 D105 Date code of manufacturing for independentlymounted control103)CNotes to table 7.2Note 4)

31、Modification:Change airflow to airflow or waterflow.Addition:Note 101) This information may be taken from the appropriate IEC equipment standard or may be as declared by themanufacturer.Note 102) The date code shall be the date or other dating period of manufacture not exceeding any three consecutiv

32、emonths. The date of manufacture is able to be abbreviated, in a nationally accepted conventional code, or in a codeaffirmed by the manufacturer. When a manufacturers code is used, the code:1. Must not repeat in less than 20 years, and;2. Must not require reference to the product records of the manu

33、facturer to determine when the product wasmanufactured.10.1.16DV D2 Modification of 10.1.16 of the Part 1 by replacing the first sentence with10.1.16DV.1 10.1.16DV.3:10.1.16DV.1 In Canada and the USA, where flying lead (pig tail) connections are used forconnection to fixed wiring, the lead or leads

34、shall be no smaller than 0,77 mm2(0,001 in2)with insulation having a nominal thickness not less than 0,6 mm (1/32 inch) and shall be aminimum of 450 mm (17-3/4 inch) as measured from the control to the end of the lead,except if the flying lead is intended to be spliced (for example by twist on conne

35、ctors) tofixed wiring within the enclosure, the flying lead shall be at least 150 mm (6 inches) long.10.1.16DV.2 Flying leads shall be provided with strain relief for attachment method 2 toprevent mechanical stress from being transmitted to terminals, splices or internal wiring.10.1.16DV.3 Complianc

36、e is checked by inspection and by applying a pull of 44 N (10 lbf)for 1 minute. During the pull the lead shall not be damaged and shall not have beendisplaced longitudinally by more than 2 mm (5/64 inch) after the test. Creepage distancesand clearances shall not have been reduced to less than the va

37、lue specified in clause 20.JANUARY 16, 2004 NATIONAL DIFFERENCES FOR UL UL 60730-2-18 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL11.101.3DV D2 Addition of 11.101.3DV.1 and 11.101.3DV.2 to the part 2:11.101.3DV.1 The operating mechanism o

38、f a manually operated switch shall not subjectparts to damage.11.101.3DV.2 Compliance with 11.101.3DV.1 is checked by inspection.27DV D2 Modification of 27 of the part 2:Delete statement that 27.2 and 27.3 are not applicable.Table H.7.2DV D2 Replacement of Table H.7.2 with Table H.7.2DV:Table H.7.2D

39、VInformation Clause or subclause Method58a AdditionSee note 1 of table H.26.273 Controls subjected to a second faultanalysisH.27.1.3.101 X104 The output condition of water and airflow cut-outs after operation101)H.26.2.102, H.26.2.103, XH.26.2.104, H.26.2.105Notes to additional items to table 7.2:Ad

40、dition:Note 101) For example, conducting or non-conducting, as applicableH.26.11DV D2 Modification of H.26.11 by adding the following after the title of thesubclause:This test is carried out in accordance with IEC 61000-4-2 except as follows:18.DVA D2 Addition of a new annex 18.DVA as follows:18.DVA

41、.1 The manufacturer shall provide regular production control, inspections, andtests. For Type 2 controls, the program shall include:a) Calibration verification and adjustment of set point under prescribedconditions and following a prescribed method;b) A 1-minute dielectric voltage-withstand test at

42、1 000 volts plus twice the ratedvoltage, or a 1-second test at 120 percent of that voltage;JANUARY 16, 2004NATIONAL DIFFERENCES FOR UL UL 60730-2-188UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULc) Determination that electromagnetic parts fu

43、nction as intended at a supplyvoltage that is 85 percent of the rated voltage for ac controls and 80 percent ofthe rated voltage for dc controls.JANUARY 16, 2004 NATIONAL DIFFERENCES FOR UL UL 60730-2-18 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJANUARY 16, 2004NATIONAL DIFFERENCES FOR UL UL 60730-2-1810No Text on This Page