UL 1686-2012 UL Standard for Safety Pin and Sleeve Configurations (Fourth Edition Reprint with Revisions Through and Including June 25 2018)《插针和套管配置》.pdf

《UL 1686-2012 UL Standard for Safety Pin and Sleeve Configurations (Fourth Edition Reprint with Revisions Through and Including June 25 2018)《插针和套管配置》.pdf》由会员分享，可在线阅读，更多相关《UL 1686-2012 UL Standard for Safety Pin and Sleeve Configurations (Fourth Edition Reprint with Revisions Through and Including June 25 2018)《插针和套管配置》.pdf（212页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1686 Pin and Sleeve CongurationsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER R

2、EPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Pin and Sleeve Congurations, UL 1686 Fourth Edition, Dated August 17, 2012 Summary of Topics This revision of ANSI/UL 1686 incorporates the addition of the 4 oclock dimensional conguration with a rated voltage not exce

3、eding 50 V. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or th

4、e date on which the changed requirement becomes effective. The revised requirements are substantially in accordance with Proposal(s) on this subject dated November 15, 2013. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form b

5、y any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no

6、 event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised

7、of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss

8、, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraph

9、s, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUP

10、ERSEDED REQUIREMENTS notice. JANUARY 8, 2014 UL 1686 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JANUARY 8, 2014 UL 1686 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT P

11、ERMISSION FROM UL AUGUST 17, 2012 (Title Page Reprinted: January 8, 2014) 1 UL 1686 Standard for Pin and Sleeve Congurations First Edition December, 1993 Second Edition July, 1998 Third Edition January, 2007 Fourth Edition August 17, 2012 This ANSI/UL Standard for Safety consists of the Fourth editi

12、on including revisions through January 8, 2014. The most recent designation of ANSI/UL 1686 as an American National Standard (ANSI) occurred on January 8, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or pro

13、posals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy

14、of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2014 UNDERWRITERS LABORATORIES INC. ANSI/UL 1686-2014UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

15、REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 General 4 CONFIGURATIONS

16、 C1 Congurations .5 C2 Congurations .16 C3 Congurations .94 C4 Congurations 114 C5 Specic Congurations .121 AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 The

17、se congurations cover attachment plugs, receptacles, and cord connectors, for use in accordance with the National Electrical Code (NEC), ANSI/NFPA 70. 1.2 These congurations do not cover devices rated at more than 800 A or for more than 600 V. 2 General 2.1 The information given in 2.1(a) 2.1(h) app

18、lies to each conguration in Sections C1 C5. a) All dimensions are in inches. b) Decimal dimensions without tolerances shall be subject to a 0.005 inch tolerance. c) Angular dimensions without tolerances shall be subject to a 1/2 degree tolerance. d) Where two values are given for the same dimension,

19、 the larger is the maximum value and the smaller the minimum value. e) Leading edges of pins and sleeves shall be free of burrs and sharp edges. f) A contour, face dimension, yoke construction, or mounting ears and dimensions for any receptacle construction that is shown depicts an acceptable constr

20、uction; other constructions may also be acceptable if tested and found to be equivalent. g) The relationship of recessing of contacts, or internal construction in a receptacle that is shown depicts an acceptable construction; other constructions may also be acceptable if tested and found to be equiv

21、alent. h) Terminal identication shall comply with the following: 1) The grounded terminal is to be identied in the Figures by the letter W . 2) The grounding terminal is to be identied in the Figures by the letter G . AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 4UL COPYRIGHTED MATERIAL N

22、OT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONFIGURATIONS C1 Congurations NOTES 1. Q is the allowable distance measured from the male contact tip to a plane perpendicular to the longitudinal axis where initial electrical engagement with the sleeve contact takes

23、 place. 2. The design of the pins shall provide a means of maintaining electrical contact force to their respective sleeve contacts. 3. The design of the ground springs shall provide a means of maintaining electrical contact with the plug sleeve when the plug is mated with the receptacle. 4. Connect

24、ors shall be rated for use in ordinary locations only. 5. Receptacles may be rated for use in Hazardous Locations. 6. Plugs shall be rated for use in Hazardous Locations. 7. Inlets shall be rated for use in ordinary locations only. This is generated text for gtxt. AUGUST 17, 2012 PIN AND SLEEVE CONF

25、IGURATIONS - UL 1686 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.1 Receptacle and connectors See note 1, 2, 3, 4 and 5. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHE

26、R REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.2 Plugs and Inlets See notes 6 and 7. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.3 Receptacles and co

27、nnectors See notes 1, 2, 3, 4 and 5. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.4 Plugs and inlets See notes 6 and 7. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL

28、1686 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.5 Receptacles and connectors See notes 1, 2, 3, 4 and 5. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 10UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTIO

29、N OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.6 Plugs and inlets See notes 6 and 7. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 11UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.7 Receptacles and connectors See

30、 notes 1, 2, 3, 4 and 5. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 12UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.8 Plugs and inlets See notes 6 and 7. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 13UL C

31、OPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C1.9 Receptacles and connectors See notes 1, 2, 3, 4 and 5. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 14UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTR

32、IBUTION WITHOUT PERMISSION FROM UL Figure C1.10 Plugs and inlets See note 6 and 7. AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 15UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL C2 Congurations C2.1 Figures C2.1 C2.38 illustrate t

33、he congurations for plugs and inlets and for receptacles and connectors of single-rated Pin and Sleeve devices of the IEC 309-2 type, Series II. The dimensions shown dene the features which enable proper mating and mating of devices only with the same service, voltage, and amperage. The plug (or inl

34、et) shroud shall have an external key which mates with a keyway in the receptacle (or connector) cavity. The key/keyway is shown at the bottom of each conguration. The ground contact is located from this point in 30 increments to provide discrete and predetermined contact patterns. The position of t

35、he female ground contact, when viewed with the keyway at the 6 oclock position, is referred to as the clock position. There is a designated clock position for each voltage and service. These drawings do not show locking, sealing cord grip, or envelope clearance dimensions. a) The main view is shown

36、with the grounding tube or pin at the 6 oclock position for reference only. See the rating conguration for the required positions. b) Holes or recesses in the frontal face, if any, other than those for contact tubes, shall not have a depth of more than 0.394 inch (10 mm). See below. c) The dimension

37、 described in (b) shall not exceed the specied limit at any point over the entire depth, and shall be within the specied limits over a minimum depth of 0.236 inch (6 mm) with the exception of a maximum of: 1) three cut-outs for receptacles or outlets provided with 2 poles plus ground, 2) four cut-ou

38、ts for receptacles or outlets provided with three poles plus ground, or 3) ve cut-outs for devices provided with three poles plus neutral plus ground, spaced around the circumference. There shall not be more than one cut-out between adjacent holes for the contact tubes and each shall not have a widt

39、h exceeding 0.590 inch (15 mm) including any radii. Holes deeper than 0.394 inch (1 mm) in the area are allowed, d) Pin detail dimensions refer to pin diameters. The contact tubes provide contact pressure and need not be cylindrical. e) The bevelling of the contact tubes may be rounded off toward th

40、e internal cylindrical surface within a distance of 1-1/2 times the maximum dimension. f) Collars shall be provided for plugs or inlet devices having rated operating voltages exceeding 500 V. g) The ends of pins may be rounded off toward the external cylindrical surface within a distance of 1-1/2 ti

41、mes the maximum dimension. h) denotes the equipment ground contact. The terminal shall be identied by the word green , the color green, or both. The terminal may additionally be marked with the earth symbol ( ). AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 16UL COPYRIGHTED MATERIAL NOT AU

42、THORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL i) N denotes the grounded line conductor contact. The terminal shall be identied by the word white , the color white, or both. The terminal may additionally be marked with the letter N . This is generated text for gtxt. JAN

43、UARY 8, 2014 PIN AND SLEEVE CONFIGURATIONS - UL 1686 17UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.1 Receptacle or connector 20 Ampere, 3 wire without pilot (Continued) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 18

44、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.1 (cont.) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 19UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C

45、2.2 Plug or inlet 20 Ampere, 3 wire without pilot (Continued) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 20UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.2 (cont.) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 16

46、86 21UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.3 Receptacle or connector 20 Ampere, 4 wire without pilot (Continued) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 22UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

47、 REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.3 (Contd) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 23UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.4 Plug or inlet 20 Ampere, 4 wire without pilot

48、(Continued) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 24UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.4 (Cont.) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 25UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FU

49、RTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.5 Receptacle or connector 20 Ampere, 5 wire without pilot (Continued) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 26UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.5 (Cont.) AUGUST 17, 2012 PIN AND SLEEVE CONFIGURATIONS - UL 1686 27UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR