SANS 61-1-2009 Cranes - Limiting and indicating devices Part 1 General《起重机 限制及标示设备 第1部分 一般》.pdf
《SANS 61-1-2009 Cranes - Limiting and indicating devices Part 1 General《起重机 限制及标示设备 第1部分 一般》.pdf》由会员分享,可在线阅读,更多相关《SANS 61-1-2009 Cranes - Limiting and indicating devices Part 1 General《起重机 限制及标示设备 第1部分 一般》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22581-0 SANS 61-1:2009 Edition 2 ISO 10245-1:2008 Edition 2SOUTH AFRICAN NATIONAL STANDARD Cranes Limiting and indicating devices Part 1:
4、General This national standard is the identical implementation of ISO 10245-1:2008, and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27
5、 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 61-1:2009 Edition 2 ISO 10245-1:2008 Edition 2 Table of changes Change No. Date Scope National foreword This South African standard was approved by National C
6、ommittee SABS TC 96, Cranes, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in April 2009. This SANS document supersedes SANS 61-1:2003 (edition 1). Reference is made in 4.2.1 of ISO 10245-1:2008 to
7、the rated capacity limiters and indicators that shall be provided on all cranes having a rated capacity of 3 t and above. In South Africa the rated capacity of all cranes is 5 t in accordance with the Occupational Health and Safety Act, 1993 (Act No. 85 of 1993) (Machinery regulation 18(2)(b)(ii),18
8、(9)(a) and 18(9)(b). In ISO 10245-1:2008, “an overturning moment of 40 000 .m“ in 4.2.1 should read “an overturning moment of 40 000 N.m“, and “slake rope“ in 4.6.1 should read “slack rope“. This standard may only be used and printed by approved subscription and freemailing clients of the SABS. Refe
9、rence number ISO 10245-1:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 10245-1 Second edition 2008-01-15 Cranes Limiting and indicating devices Part 1: General Appareils de levage charge suspendue Limiteurs et indicateurs Partie 1: Gnralits SANS 61-1:2009This standard may only be used and printed by ap
10、proved subscription and freemailing clients of the SABS.ISO 10245-1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and
11、installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software
12、products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is fou
13、nd, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mic
14、rofilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO
15、2008 All rights reservedSANS 61-1:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 10245-1:2008(E) ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Safety requ
16、irements and/or measures . 3 5 Inspection 7 6 Maintenance 7 7 Operating instructions and operator training8 8 Information for use . 8 Bibliography . 9 SANS 61-1:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 10245-1:2008(E) iv ISO 2008
17、 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a s
18、ubject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission
19、(IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical comm
20、ittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not
21、be held responsible for identifying any or all such patent rights. ISO 10245-1 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 8, Jib cranes. This second edition cancels and replaces the first edition (ISO 10245-1:1994), which has been technically revised. ISO 10245 consists o
22、f the following parts, under the general title Cranes Limiting and indicating devices: Part 1: General Part 2: Mobile cranes Part 3: Tower cranes Part 4: Jib cranes Part 5: Overhead travelling and portal bridge cranes SANS 61-1:2009This standard may only be used and printed by approved subscription
23、and freemailing clients of the SABS.INTERNATIONAL STANDARD ISO 10245-1:2008(E) ISO 2008 All rights reserved 1 Cranes Limiting and indicating devices Part 1: General 1 Scope This part of ISO 10245 specifies general requirements for limiting and indicating devices for cranes that are applicable to loa
24、ds and motions, performance and environment. These devices restrict operation and/or provide the operator or other persons with operational information. The specific requirements for the various types of crane are given in the other parts of ISO 10245. It is emphasized that the safe and reliable ope
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SANS6112009CRANESLIMITINGANDINDICATINGDEVICESPART1GENERAL 起重机 限制 标示 设备 部分 一般 PDF

链接地址:http://www.mydoc123.com/p-1031471.html