SANS 300786-2005 Fixed Radio Systems Point-to-point equipment Sub-STM-1 digital radio systems operating in the 13 GHz 15 GHz and 18 GHz frequency bands with about 14 MHz co-polar c.pdf

《SANS 300786-2005 Fixed Radio Systems Point-to-point equipment Sub-STM-1 digital radio systems operating in the 13 GHz 15 GHz and 18 GHz frequency bands with about 14 MHz co-polar c.pdf》由会员分享，可在线阅读，更多相关《SANS 300786-2005 Fixed Radio Systems Point-to-point equipment Sub-STM-1 digital radio systems operating in the 13 GHz 15 GHz and 18 GHz frequency bands with about 14 MHz co-polar c.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 33.060.30 ISBN 0-626-17393-0 SANS 300786:2005Edition 1 ETSI EN 300786:2001Edition V1.3.1SOUTH AFRICAN NATIONAL STANDARD Fixed Radio Systems; Point-to

4、-point equipment; Sub-STM-1 digital radio systems operating in the 13 GHz, 15 GHz and 18 GHz frequency bands with about 14 MHz co-polar channel spacing This national standard is the identical implementation of ETSI EN 300786:2001 and is adopted with the permission of the European Telecommunications

5、Standards Institute. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 300786:2005 Edition 1 ETSI EN 300786:2001 Edition V1.3.1 Table of changes C

6、hange No. Date Scope Abstract Specifies the minimum performance parameters for terrestrial fixed services radio communications equipment for operation in the 13 GHz, 15 GHz and 18 GHz frequency bands. Keywords architecture, DRRS, point-to-point, radio, SDH, STM, transmission. National foreword This

7、South African standard was approved by National Committee StanSA TC 74, Communication technology, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. In South Africa, spectrum band plans are regulated by the Independent Communications Authori

8、ty of South Africa (ICASA). The South African Table of Frequency Allocations is obligatory for South Africa and will override any reference to frequency ranges as mentioned in this standard. ETSI EN 300 786 VI .3.1 (2001-02) European Standard (Telecommunications series) Fixed Radio Systems; Point-to

9、-point equipment; Sub-STM-I digital radio systems operating in the 13 GHz, 15 GHz and 18 GHz frequency bands with about 14 MHz co-polar channel spacing ETSI EN 300 786 V1.3.1 (2001-02) Reference RENITM-04111-05 Keywords architecture, DRRS, radio, SDH, STM, transmission, point-to-point ETSl 650 Route

10、 des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Siret No 348 623 562 00017 - NAF 742 C Association a but non lucratif enregistree a la Sous-Prefecture de Grasse (06) No 7803188 Important notice Individual copies of the present document can be downloaded from: htt:llwww.etsi.org The present doc

11、ument may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSl printers of the

12、 PDF version kept on a specific network drive within ETSl Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status, Information on the current status of this and other ETSl documents is available at htt:/www.etsi.orq/tblstatus/ If yo

13、u find errors in the present document, send your comment to: editoretsi .fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute

14、2001. All rights reserved. 3 ETSl EN 300 786 V1.3.1 (2001-02) Contents Intellectual Property Rights 5 Foreword 5 1 Scope 6 2 References 7 3 Definitions. symbols and abbreviations . 9 3.1 Definitions 9 3.2 Symbols 9 3.3 Abbreviations 9 General characteristics . 10 Frequency Bands and Channel Arrangem

15、ents 10 . Performance and availability requirements 10 Types of Installation 10 . Environmental Conditions 10 Equipment within weather protected locations (indoor locations) 10 Equipment for not-weather protected locations (outdoor locations) . 11 . Electromagnetic compatibility conditions 11 . Mech

16、anical requirements 11 Power supply 11 TMN Interface 11 Branching 1 feeder / antenna requirements 11 Antenna radiation patterns 11 Return loss . 11 . Intermodulation Products 11 . Equipment Flanges 12 Block Diagram 12 Lightning protection 12 Baseband characteristics . 12 Synchronous Digital Hierarch

17、y . 12 Plesiochronous Digital Hierarchy . 12 Transmitter characteristics 13 Output Power 13 Automatic Transmit Power Control (ATPC) 13 RF Spectrum Masks 14 Discrete CW components exceeding the spectrum mask limit . 14 Spectral lines at the symbol rate . 14 Other spectral lines 14 . Spurious Emission

18、s 15 Spurious Emissions . External 15 . Spurious Emissions . Internal 16 Radio Frequency Tolerance . 16 . . . Receiver characteristics 16 Local Oscillator Frequency Tolerance 16 Receiver IF 16 Receiver Image(s) Rejection 16 . Spurious Emissions 17 Spurious Emissions - External 17 Spurious Emissions

19、- Internal . 17 . Input Level Range 17 . System characteristics 18 . Equipment Background BER 18 BER as a Function of Receiver Input Level (without interference) 18 ETSl 8.3 Interference Sensitivity 18 8.3.1 Co-channel Interference Sensitivity 18 8.3.1A Method of testing co-channel interference sens

20、itivity 18 8.3.2 Adjacent Channel Sensitivity 19 8.3.2A Method of testing adjacent channel (at about 14 MHz channel spacing) interference sensitivity . 19 8.3.3 C W Spurious Interference . 19 8.4 Distortion Sensitivity . 20 Annex A (informative): Additional information 24 A.l Branching 1 feeder / an

21、tenna requirement 24 A . 1.1 Antenna requirements 24 A.l.l.l Antenna radiation patterns 24 A.1.1.2 Return Loss . 24 A.2 ATPC . 24 Annex B (informative): Bibliography . 25 History . 26 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared

22、to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members. and can be found in ETSI SR 000 3 14: Yntellectual Property Rights (IPRs); Essential, orpotentially Essential, IPRs not$ed to ETSI in respect of ETSIstandards“, which is avail

23、able from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:l/www.etsi.org/ipr). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI S

24、R 000 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). The present document contains the m

25、inimum technical requirements to ensure compatibility of products and conformance with radio regulations across ETSI member states. Radio terminals from different manufacturers are not required to interwork at radio frequency (i.e. no common air interface). The present document defines the requireme

26、nts of radio terminal and radio-relay equipment and associated interfaces. The requirements for multiplex, network management and antenna 1 feeder equipment may be addressed elsewhere. The former title of the present document was: “Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRR

27、S); Sub-STM- 1 DRRS operating in the 13 GHz, 15 GHz and 18 GHz frequency bands with about 14 MHz co-polar channel spacing“. National transposition dates Date of adoption of this EN: 9 February 200 1 Date of latest announcement of this EN (doa): 31 May 2001 Date of latest publication of new National

28、Standard or endorsement of this EN (dopie): 30 November 2001 Date of withdrawal of any conflicting National Standard (dow): 30 November 200 1 6 ETSI EN 300 786 V1.3.1 (2001-02) Scope The present document specifies the minimum performance parameters for terrestrial fixed services radiocommunications

29、equipment, as given below, for operation in the 13 GHz (12,75 GHz to 13,25 GHz), 15 GHz (14,5 GHz to 15,35 GHz) and 18 GHz (17,7 GHz to 19,7 GHz) frequency bands. The present document covers equipment for the transmission of sub-STM-1 digital signals with a VC3 payload capacity. The standardization

30、of sub-STM-1 radio systems for 13 GHz, 15 GHz and 18 GHz bands has been prepared to ensure the compatibility with the existing plesiochronous and the new synchronous systems concerning frequency plans and performance. The application of these digital radio-relay systems is anticipated to be for poin

31、t-to-point links in local, regional and national networks, mobile base station connections, customer and access links. Consideration has to be given to special requirements of the local and access network, e.g. simple towers with less space for antenna, different network structures with high density

32、 nodes. The systems considered shall operate in these networks having regard for existing hop lengths, which mainly depend on the frequency band envisaged, the performance objectives set by relevant ITU-R Recommendations or national Network Operators requirements and existing propagation characteris

33、tics. The hop lengths are considered to be normally up to 37 km in the 13 GHz band, up to 30km in the 15 GHz band and up to 20 km in the 18 GHz band. The parameters to be specified fall into two categories: a) Those that are required to provide compatibility between RF channels occupied by different

34、 sources of equipment on the same route connected either to: - separate antennas; or to - separate polarization of the same antenna. NOTE: Equipment supplied by different manufactures on the same path and using different polarizations shall operate on different frequencies. b) Parameters defining th

35、e transmission quality of the proposed system. The standardization deals with IF, RF and baseband characteristics relevant to Sub-STM-1 SDH transmission. Spurious emissions and EMC requirements are also included in the present document. Safety regulations are outside the scope of the present documen

36、t. References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-speci fic. For a specific reference, subseque

37、nt revisions do not apply. For a non-specific reference, the latest version applies. I ITU-R Recommendation F.750-3: “Architectures and functional aspects of radio-relay systems for synchronous digital hierarchy (SDH) based networks I. 21 ITU-R Recommendation F.75 1-2: “Transmission characteristics

38、and performance requirements of radio-relay systems for SDH-based networks“. 31 ITU-R Recommendation F.634-4: “Error performance objectives for real digital radio-relay links forming part of the high-grade portion of international digital connections at a bit rate below the primary rate within an in

39、tegrated services digital network“. 41 ITU-R Recommendation F.696-2: “Error performance and availability objectives for hypothetical reference digital sections forming part or all of the medium-grade portion of an ISDN connection at a bit rate below the primary rate utilizing digital radio-relay sys

40、tems“. 51 ITU-R Recommendation F.697-2: “Error performance and availability objectives for the local-grade portion at each end of an ISDN connection at a bit rate below the primary rate utilizing digital radio-relay systems“. 61 ITU-T Recommendation G.821: “Error performance of an international digi

41、tal connection operating at a bit rate below the primary rate and forming part of an integrated services digital network“. 71 ITU-T Recommendation G.826: “Error performance parameters and objectives for international, constant bit rate digital paths at or above the primary rate“. 81 ITU-R Recommenda

42、tion F.497-6: “Radio-fi-equency channel arrangements for radio-relay systems operating in the 13 GHz frequency band“. 91 ITU-R Recommendation F.636-3: “Radio-fi-equency channel arrangements for radio-relay systems operating in the 15 GHz band“. lo ITU-R Recommendation F.595-6: “Radio-frequency chann

43、el arrangements for radio-relay systems operating in the 18 GI+ frequency band“. 1111 ETSI ETS 300 019 (Parts 1 and 2): “Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment“. I21 ETSI EN 300 385: “Electromagnetic compatibility and Radio spect

44、rum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment“. I31 ETSI ETS 300 119: “Equipment engineering (EE); European telecommunication standard for equipment practice“. I41 ETSI ETS 300 132: “Equipment engineering (EE); Power supply interface at

45、 the input to telecommunications equipment“. 151 ITU-T Recommendation G.784: “Synchronous digital hierarchy (SDH) management“. I61 ITU-T Recommendation G.773: “Protocol suites for Q-interfaces for management of transmission systems“. 171 ITU-T Recommendation G.703: “Physicallelectrica1 characteristi

46、cs of hierarchical digital interfaces“. 8 ETSl EN 300 786 V1.3.1 (2001-02) ITU-T Recommendation G.707: “Network node interface for the synchronous digital hierarchy (SDH)“. ITU-T Recommendation G.781: “Structure of Recommendations on equipment for the synchronous digital hierarchy (SDH)“. ITU-T Reco

47、mmendation G.782: “Types and general characteristics of synchronous digital hierarchy (SDH) equipment“. ITU-T Recommendation G.783: “Characteristics of synchronous digital hierarchy (SDH) equipment functional blocks“. ITU-T Recommendation G.957: “Optical interfaces for equipments and systems relatin

48、g to the synchronous digital hierarchy“. ETSI ETS 300 174: “Network Aspects (NA); Digital coding of component television signals for contribution quality applications in the range 34 - 45 Mbitls“. ITU-R Recommendation F.695: “Availability objectives for real digital radio-relay links forming part of

49、 a high grade circuit within an integrated services digital network“. ETSI EN 300 833: “Fixed Radio Systems; Point to Point Antennas; Antennas for point-to-point fixed radio systems operating in the frequency band 3 GHz to 60 GHz“. CEPTIERC Recommendation 74-01 : “Spurious Emissions“. ITU-R Recommendation F. 1092-1 : “Error performance objectives for constant bit rate digital path at or above the primary rate carried by digital radio-relay systems which may form part of the international portion of the 27 500 km hypothetical reference path“. ITU-R Recommendation F. 1