SANS 21003-1-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 1 General《建筑物内冷热水装置的多层管道系统 第1部分 一般》.pdf

《SANS 21003-1-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 1 General《建筑物内冷热水装置的多层管道系统 第1部分 一般》.pdf》由会员分享，可在线阅读，更多相关《SANS 21003-1-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 1 General《建筑物内冷热水装置的多层管道系统 第1部分 一般》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21116-5 SANS 21003-1:2008 Edition 1 ISO 21003-1:2007 Edition 1SOUTH AFRICAN NATIONAL STANDARD Multilayer piping systems for hot and cold w

4、ater installations inside buildings Part 1: General This national standard is the identical implementation of ISO 21003-1:2007 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 p

5、retoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 21003-1:2008 Edition 1 ISO 21003-1:2007 Edition 1 Table of changes Change N

6、o. Date Scope National foreword This South African standard was approved by National Committee StanSA SC 5120.12K, Water and sanitation Equipment and systems Plastics pipes and fittings, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. Thi

7、s SANS document was published in May 2008. This adopted Final Draft International Standard (FDIS) has the status of a South African National Standard. The FDIS will be replaced by the final ISO document at the time of its publication. This standard may only be used and printed by approved subscripti

8、on and freemailing clients of the SABS. ISO 2007 All rights reserved Document type: International Standard Document subtype: Document stage: (50) Approval Document language: E C:DOCUME1petermLOCALS1TempISO FDIS 21003-1.doc STD Version 2.1 ISO TC 138/SC 2 Date: 2007-07-01 ISO/FDIS 21003-1:2007(E) ISO

9、 TC 138/SC 2/WG 5 Secretariat: SNV Multilayer piping systems for hot and cold water installations inside buildings Part 1: General Systmes de canalisations en multicouches pour installations deau chaude et froide lintrieur des btiments Partie 1: Gnralits SANS 21003-1:2008This standard may only be us

10、ed and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-1:2007(E) ii Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft n

11、or any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address b

12、elow or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted.

13、 SANS 21003-1:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-1:2007(E) ISO 2007 All rights reserved iiiContents Foreword.iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .3 3.1 Definitions related t

14、o construction 3 3.2 Definitions related to geometry4 3.3 Definitions related to service conditions 6 3.4 Definitions related to materials 6 3.5 Definitions related to material characteristics6 3.6 Definitions related to temperatures.7 4 Symbols and abbreviated terms 8 4.1 Symbols8 4.2 Abbreviated t

15、erms .9 5 Classification of service conditions 10 6 Material .11 6.1 General11 6.2 Influence on water intended for human consumption.11 Annex A (normative) List of the reference product standards.12 Bibliography13 SANS 21003-1:2008This standard may only be used and printed by approved subscription a

16、nd freemailing clients of the SABS.ISO/FDIS 21003-1:2007(E) iv ISO 2007 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried o

17、ut through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO c

18、ollaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International

19、 Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elemen

20、ts of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21003-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and

21、 fittings for water supplies. ISO 21003 consists of the following parts, under the general title Multilayer piping systems for hot and cold water installations inside buildings: Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessme

22、nt of conformity ISO 21003 does not incorporate a Part 4: Ancillary equipment and a Part 6: Guidance for installation. For ancillary equipment separate standards can apply. A guidance for installation for multilayer piping systems made from different materials, intended to be used for hot and cold w

23、ater installations, is covered by ENV 12108. SANS 21003-1:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-1:2007(E) ISO 2007 All rights reserved vIntroduction The system Standard, of which this is Part 1, specifies the requir

24、ements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside buildings. In respect of potential adverse effects on the quality of water intended for human consumption, caused by the product covered by this standard: This Stand

25、ard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of th

26、is product stay in force. Requirements and test methods for components of the piping system are specified in ISO 21003-2 and ISO 21003- 3 of the ISO 21003-series. Characteristics for fitness of purpose (mainly for joints) are covered in ISO 21003-5. CEN ISO/TS 21003-7 gives guidance for the assessme

27、nt of conformity. This part of ISO 21003 specifies the general aspects of the multilayer piping systems. At the date of publication of this standard, System Standards for piping systems of plastics materials used for the same application are stated in Annex A. SANS 21003-1:2008This standard may only

28、 be used and printed by approved subscription and freemailing clients of the SABS.SANS 21003-1:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 21003-1:2007(E) ISO 2007 All rights reserved 1Multila

29、yer piping systems for hot and cold water installations inside buildings Part 1: General 1 Scope This part of ISO 21003 specifies the general aspects of multilayer piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not inte

30、nded for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1). Part 1 of the ISO 21003-series is one part of a reference product standard. This series is applicable to multilayer pipes, fittings, the

31、ir joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations in conjunction with all other parts of ISO 21003. This standard covers a range of service conditions (application classes) and design pressures. For values of

32、 T D , T maxand T malin excess of those in Table 1, this standard does not apply. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installatio

33、n practices or codes. The polymeric materials used for the stress designed layers are the following: polyethylene of raised temperature resistance polybutylene (PB), (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) and chlorinated poly(vinyl chloride) (PVC-C). NOTE For the purpose of thi

34、s International Standard crosslinked polyethylene (PE-X) as well as adhesives are to be considered as thermoplastic materials. PE-X shall be crosslinked and shall comply with the requirements of the reference product standard. NOTE Solid wall pipes with thin outer layers (e.g. as a protection layer

35、or a barrier layer) are not covered by ISO 21003 but are specified in the amendments of the ISO1587x-series. The total thickness of the outer layers, including the thickness of adhesives, barrier and/or protective layers, shall be 0.4 mm. 2 Normative references The following referenced documents are

36、 indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbers ISO 472, Plastics Vocabulary ISO 4

37、97, Guide to the choice of series of preferred number and of series containing more rounded values of preferred numbers ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics ISO 9080, Plastics piping and ducting systems Determination of long-

38、term hydrostatic strength of thermoplastics material in pipe form by extrapolation SANS 21003-1:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-1:2007(E) 2 ISO 2007 All rights reservedISO 10508, Plastics piping systems for ho

39、t and cold water installations Guidance for classification and design ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications Classification and designation Overall service (design) coefficient ISO 15874-1, Plastics piping systems for hot and cold water installations Pol

40、ypropylene (PP) Part 1: General ISO 15874-2, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 2: Pipes ISO 15874-3, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 3: Fittings ISO 15874-5, Plastics piping systems for hot and co

41、ld water installations Polypropylene (PP) Part 5: Fitness for purpose of the system ISO 15875-1, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 1: General ISO 15875-2, Plastics piping systems for hot and cold water installations Crosslinked polyethy

42、lene (PE-X) Part 2: Pipes ISO 15875-3, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 3: Fittings ISO 15875-5, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 5: Fitness for purpose of the system ISO

43、 15876-1, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 1: General ISO 15876-2, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 2: Pipes ISO 15876-3, Plastics piping systems for hot and cold water installations Polybutylene (P

44、B) Part 3: Fittings ISO 15876-5, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 5: Fitness for purpose of the system ISO 15877-1, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 1: General ISO 15877-2, Pl

45、astics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 2: Pipes ISO 15877-3, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings ISO 15877-5, Plastics piping systems for hot and cold

46、water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system ISO/FDIS 22391-1, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General ISO/FDIS 22391-2, Plastics piping systems for ho

47、t and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes ISO/FDIS 22391-3, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings ISO/FDIS 22391-5, Plastics piping systems for hot a

48、nd cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system SANS 21003-1:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-1:2007(E) ISO 2007 All rights reserved 3

49、3 Terms and definitions For the purposes of this Part of ISO 21003, the terms and definitions given in ISO 3, ISO 472 and ISO 1043-1 and the following apply. 3.1 Definitions related to construction 3.1.1 multilayer pipe pipe comprised of different stress designed layers. Multilayer pipes related to this standard shall be constructed with a inner layer made of plastics. 3.1.2 multilayer M pipe pipe comprised of stre