SANS 1261-3-2008 Performance requirements for retail textiles Part 3 Piece-goods for men-s and boys- wear《零售纺织品性能要求 第3部分 男子及男孩穿戴计件货物》.pdf

《SANS 1261-3-2008 Performance requirements for retail textiles Part 3 Piece-goods for men-s and boys- wear《零售纺织品性能要求 第3部分 男子及男孩穿戴计件货物》.pdf》由会员分享，可在线阅读，更多相关《SANS 1261-3-2008 Performance requirements for retail textiles Part 3 Piece-goods for men-s and boys- wear《零售纺织品性能要求 第3部分 男子及男孩穿戴计件货物》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21226-1 SANS 1261-3:2008Edition 2.1SOUTH AFRICAN NATIONAL STANDARD Performance requirements for retail textiles Part 3: Piece-goods for me

4、ns and boys wear Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 1261-3:2008 Edition 2.1 Table of changes Change No. Date Scope Amdt 1 2008 Amen

5、ded to update referenced standards. Foreword This South African standard was approved by National Committee StanSA SC 5110.01E, Textiles Performance requirements, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published

6、 in July 2008. This document supersedes SANS 1261-3:2007 (edition 2). SANS 1261 consists of the following parts, under the general title Performance requirements for retail textiles: Part 1: Household piece-goods and articles. Part 2: Piece-goods for womens and girls wear. Part 3: Piece-goods for me

7、ns and boys wear. A vertical line in the margin shows where the text has been technically modified by amendment No.1. Annex A is for information only. Introduction In most instances in this part of SANS 1261, no requirements are specified for fibre content or structural details such as mass per area

8、, threads per length, weave, or knit structures, although it is recognized that these properties will largely determine the essential character and the aesthetic appeal of a fabric. Setting these properties outside the scope of this part of SANS 1261 has been deliberate in order to allow the widest

9、possible application of the standard and the greatest flexibility of manufacture. The main purpose is to provide a standard that will accommodate the prevailing retail demands for textiles while at the same time ensuring that these textiles will be acceptable in respect of their basic performance pr

10、operties (for example, strength, dimensional stability and colour fastness). The emphasis throughout is on these basic properties. Frequently made claims pertaining to retail textile piece-goods for mens and boys wear (such as “crease resistant“, “fully shrunk“ and “7-year quality“) are not covered

11、by the range of tests specified, and compliance with the requirements in this part of SANS 1261 cannot be taken as a substantiation of such claims. SANS 1261-3:2008 Edition 2.1 1 Contents Page Foreword Introduction 1 Scope 3 2 Normative references . 3 3 Terms and definitions . 4 4 Basic requirements

12、 and method of test for dimensional changes on laundering . 4 4.1 General requirements 4 4.2 Breaking strength, tearing strength, dimensional changes and seaming properties . 5 4.3 Colour fastness 5 4.4 Method of test for dimensional changes on laundering . 5 5 Specific requirements and methods of t

13、est 6 5.1 Woven dressing-gown fabrics (excluding terry fabrics) . 6 5.2 Woven lounge-suit fabrics 7 5.3 Woven overall fabrics . 8 5.4 Woven pyjama fabrics 9 5.5 Woven shirt fabrics . 10 5.6 Woven slacks and shorts fabrics . 11 5.7 Woven swimwear fabrics . 12 5.8 Woven necktie fabrics 13 5.9 Woven sp

14、ortswear fabrics 14 5.10 Knitted dressing-gown fabrics 15 5.11 Knitted pyjama fabrics 16 5.12 Knitted shirt fabrics . 17 5.13 Knitted slacks, shorts and safari-suit fabrics 18 5.14 Knitted swimwear fabrics . 19 5.15 Knitted underwear fabrics 20 5.16 Knitted sportswear fabrics (excluding elasticated

15、fabrics) . 21 Annex A (informative) Quality verification of retail textile piece-goods for mens and boys wear . 22 Bibliography 22 SANS 1261-3:2008 Edition 2.1 2 This page is intentionally left blank SANS 1261-3:2008 Edition 2.1 3 Performance requirements for retail textiles Part 3: Piece-goods for

16、mens and boys wear 1 Scope This part of SANS 1261 specifies performance requirements for retail textile piece-goods used in the manufacturing of mens and boys wear. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references,

17、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Information on currently valid national and international standards can be obtained from Standards South Africa. ISO 3175-2, Textiles Professional care, dryclean

18、ing and wetcleaning of fabrics and garments Part 2: Procedure for testing performance when cleaning and finishing using tetrachloroethene. SANS 105-B02/ISO 105-B02, Textiles Tests for colour fastness Part B02: Colour fastness to artificial light: Xenon arc fading lamp test. SANS 105-D01/ISO 105-D01,

19、 Textiles Tests for colour fastness Part D01: Colour fastness to dry cleaning. SANS 105-E02/ISO 105-E02, Textiles Tests for colour fastness Part E02: Colour fastness to sea water. SANS 105-E03/ISO 105-E03, Textiles Tests for colour fastness Part E03: Colour fastness to chlorinated water (swimming-po

20、ol water). SANS 105-E04/ISO 105-E04, Textiles Tests for colour fastness Part E04: Colour fastness to perspiration. SANS 105-X12/ISO 105-X12, Textiles Tests for colour fastness Part X12: Colour fastness to rubbing. SANS 1097, Dimensional changes in textile fabrics caused by immersion in cold water. S

21、ANS 1261-3:2008 Edition 2.1 4 SANS 1270, General requirements for woven textile piece-goods and household articles. SANS 5382 (SABS SM 382), Textiles Tearing strength of fabrics: wing-rip tear test. Amdt 1 SANS 5726, Seaming properties of woven textile fabrics. SANS 6009, Abrasion resistance of text

22、ile fabrics (Martindale test). SANS 6026:2005, Dry-cleaning pretreatment of textile fabrics. SANS 6116, Resistance of textile fabrics to pilling and fuzzing (Random tumble method). SANS 10004, Terms and definitions for textiles and textile merchandise. SANS 11108 (SABS SM 1108:1990), Washing pretrea

23、tment of textile fabrics. SANS 11166:2006, Textiles Colour fastness to domestic washing procedures. SANS 11167:2005, Textiles Dimensional stability during domestic washing and drying procedures. SANS 13934-1/ISO 13934-1, Textiles Tensile properties of fabrics Part 1: Determination of maximum force a

24、nd elongation at maximum force using the strip method. SANS 13937-3/ISO 13937-3, Textiles - Tear properties of fabrics Part 3: Determination of tear force of wing-shaped test specimens (Single tear method). Amdt 1 SANS 13938-1/ISO 13938-1, Textiles Bursting properties of fabrics Part 1: Hydraulic me

25、thod for determination of bursting strength and bursting distension. 3 Terms and definitions For the purposes of this document, the terms and definitions given in SANS 10004 and the following apply. 3.1 performance requirement specified limit for the value (obtained by a specified test and expressed

26、 in appropriate units) of a property by which a fabric or a made-up article can be judged to determine whether it will, in respect of the property tested, prove generally acceptable during normal use 4 Basic requirements and method of test for dimensional changes on laundering 4.1 General requiremen

27、ts The relevant general requirements of SANS 1270 shall apply. NOTE Guidance on the verification of the quality of retail textile piece-goods for mens and boys wear is given in annex A. SANS 1261-3:2008 Edition 2.1 5 4.2 Breaking strength, tearing strength, dimensional changes and seaming properties

28、 Unless otherwise stated, the requirements given shall apply equally to both warp (length) direction and weft (width) direction, and in the case of seaming properties, and, unless inconsistent with the text, both before and after washing or dry cleaning, as relevant. 4.3 Colour fastness 4.3.1 The va

29、lues specified shall be the minimum numerical ratings, determined in accordance with the relevant test method and, unless otherwise stated, the requirements shall apply to dyed or printed fabrics only. 4.3.2 Where provisions are made for both washing and dry-cleaning properties, the fabric should be

30、 tested as washable or dry cleanable (or both), according to the manufacturers recommendation. 4.4 Method of test for dimensional changes on laundering Unless otherwise stated, use drying procedure A of SANS 11167:2005 in all cases. SANS 1261-3:2008 Edition 2.1 6 5 Specific requirements and methods

31、of test 5.1 Woven dressing-gown fabrics (excluding terry fabrics) The requirements and methods of test for woven dressing-gown fabrics (excluding terry fabrics) are given in table 1. Table 1 Woven dressing-gown fabrics (excluding terry fabrics) 1 2 3 Propertya Requirement Method of test Breaking str

32、ength, N, min. . 180 SANS 13934-1 Seaming properties: SANS 5726 resistance to opening at seam, N, min. . strength at seams, N, min. 65 80 Tearing strength: SANS 13937-3 median peak value, N, min. 4 Dimensional changes on: laundering, %, max. SANS 11167:2005, heat-set synthetics . 3 washing procedure

33、 F4 or T4aother fabrics . 5 washing procedure F2 or T2adry cleaning, %, max. 3 ISO 3175-2 Colour fastness to: light 4 SANS 105-B02 washing SANS 11166:2006, heat-set synthetics procedure A other fabrics procedure C change in colour . staining of adjacent fabrics . 4 4 dry cleaning SANS 105-D01 change

34、 in colour 4 perspiration SANS 105-E04 change in colour staining of adjacent fabrics 4 3-4 rubbing SANS 105-X12 dry . wet . 4 3-4 aSee also clause 4. Amdt 1 SANS 1261-3:2008 Edition 2.1 7 5.2 Woven lounge-suit fabrics The requirements and methods of test for woven lounge-suit fabrics are given in ta

35、ble 2. Table 2 Woven lounge-suit fabrics 1 2 3 Propertya Requirement Method of test Breaking strength, N, min. . 330 SANS 13934-1 Seaming properties: SANS 5726 resistance to opening at seam, N, min. . strength at seams, N, min. 110 165 Resistance to pillingb, rating, min. 3,5 (slight to moderate) SA

36、NS 6116 Resistance to abrasion: SANS 6009crubs to end point, min. colour change at 10 000 rubs, min. 30 000 3 Dimensional changes on dry cleaning, %, max. . 2 ISO 3175-2 Colour fastness to: light 4 SANS 105-B02 dry cleaning SANS 105-D01 change in colour 4 perspiration SANS 105-E04 change in colour s

37、taining of adjacent fabrics 4 3-4 rubbing SANS 105-X12 dry . wet . 4 3-4 aSee also clause 4. bOnly applicable to blended fabrics of synthetic and natural fibres, and tested after dry cleaning in accordance with SANS 6026:2005, procedure B. cUsing a pressure of 9 kPa. SANS 1261-3:2008 Edition 2.1 8 5

38、.3 Woven overall fabrics The requirements and methods of test for woven overall fabrics are given in table 3. Table 3 Woven overall fabrics 1 2 3 Propertya Requirement Method of test Breaking strength, N, min. . 320 SANS 13934-1 Seaming properties: SANS 5726 resistance to opening at seam, N, min. .

39、strength at seams, N, min. 110 210 Tearing strength: SANS 13937-3 median peak value, N, min. 11 Resistance to pillingb, rating, min. 3,5 (slight to moderate) SANS 6116 Dimensional changes on laundering, %, max. SANS 11167:2005, cellulosic fabrics 3 washing procedure F2 or T2aother fabrics . 3 washin

40、g procedure F3 or T3aColour fastness to: light 4 SANS 105-B02 washing SANS 11166:2006, cellulosic fabrics procedure C other fabrics procedure B change in colour . staining of adjacent fabrics . 4 3 perspiration SANS 105-E04 change in colour staining of adjacent fabrics 4 3-4 rubbing SANS 105-X12 dry

41、 . wet . 4 3-4 aSee also clause 4. bOnly applicable to blended fabrics of synthetic and natural fibres, and tested after washing in accordance with SANS 11108:1990, procedure A or procedure B, as relevant. Amdt 1 SANS 1261-3:2008 Edition 2.1 9 5.4 Woven pyjama fabrics The requirements and methods of

42、 test for woven pyjama fabrics are given in table 4. Table 4 Woven pyjama fabrics 1 2 3 Propertya Requirement Method of test Breaking strength, N, min. . 230 SANS 13934-1 Seaming properties: SANS 5726 resistance to opening at seam, N, min. . strength at seams, N, min. 65 115 Tearing strength: SANS 1

43、3937-3 median peak value, N, min. 9 Dimensional changes on laundering, %, max. SANS 11167:2005, cellulosic fabrics . 5 washing procedure F2 or T2aother fabrics 5 washing procedure F4 or T4aColour fastness to: light 4 SANS 105-B02 washing SANS 11166:2006, procedure Cchange in colour . staining of adj

44、acent fabrics . 4 4 perspiration SANS 105-E04 change in colour staining of adjacent fabrics 4 3-4 rubbing SANS 105-X12 dry . wet . 4 3-4 aSee also clause 4. Amdt 1 SANS 1261-3:2008 Edition 2.1 10 5.5 Woven shirt fabrics The requirements and methods of test for woven shirt fabrics are given in table

45、5. Table 5 Woven shirt fabrics 1 2 3 Propertya Requirement Method of test Breaking strength, N, min. . 230 SANS 13934-1 Seaming properties: SANS 5726 resistance to opening at seam, N, min. . strength at seams, N, min. 65 115 Tearing strength: SANS 13937-3 median peak value, N, min. 7 Resistance to p

46、illingb, rating, min. 4 (slight) SANS 6116 Resistance to abrasion: SANS 6009crubs to end point, min. colour change at 2 500 rubs, min. 5 000 3 Dimensional changes on laundering, %, max. 3 SANS 11167:2005, washing procedure F2 or T2aColour fastness to: light 4 SANS 105-B02 washing SANS 11166:2006, pr

47、ocedure Cchange in colour staining of adjacent fabrics 4 4 perspiration SANS 105-E04 change in colour staining of adjacent fabrics 4 3-4 rubbing SANS 105-X12 dry . wet . 4 3-4 aSee also clause 4. b Only applicable to blended fabrics of synthetic and natural fibres, and tested after washing in accord

48、ance with SANS 11108:1990, procedure A. c Using a pressure of 9 kPa. Amdt 1 SANS 1261-3:2008 Edition 2.1 11 5.6 Woven slacks and shorts fabrics The requirements and methods of test for woven slacks and shorts fabrics are given in table 6. Table 6 Woven slacks and shorts fabrics 1 2 3 Propertya Requi

49、rement Method of test Breaking strength, N, min. . 330 SANS 13934-1 Seaming properties: SANS 5726 resistance to opening at seam, N, min. . strength at seams, N, min. 110 165 Tearing strength: SANS 13937-3 median peak value, N, min. 11 Resistance to pillingb, rating, min. 3,5 (slight to moderate) SANS 6116 Resistance to abrasion: SANS 6009crubs to end point, min. colour change at 10 000 rubs, min. 20 000 3 Dimensional changes on: laundering, %, max. SANS 11167:2005, cellulosic fabrics 3 washing procedure F2 or T2