SAE MA 2263-1993 Ferrule Sleeve Swaged Threadless Coupling Flexible Fixed Cavity Self-Bonding Metric《箍 套管 旋锻 螺纹耦合 柔性的 固定空腔 自粘合 米制的》.pdf

《SAE MA 2263-1993 Ferrule Sleeve Swaged Threadless Coupling Flexible Fixed Cavity Self-Bonding Metric《箍 套管 旋锻 螺纹耦合 柔性的 固定空腔 自粘合 米制的》.pdf》由会员分享，可在线阅读，更多相关《SAE MA 2263-1993 Ferrule Sleeve Swaged Threadless Coupling Flexible Fixed Cavity Self-Bonding Metric《箍 套管 旋锻 螺纹耦合 柔性的 固定空腔 自粘合 米制的》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FERRULE, SLEEVE, SWAGED, THREADLESS, COUPLING, FLEXIBLE, FIXED CAVITY, SELF-BONDING,METRIC MA2263Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electron

2、ic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1993-1

3、1REAFFIRMED2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3A FEDERAL SUPPLY CLASS 4730MA2263 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: MA2241 /3/SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport

4、 is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE i

5、nvites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA2263 RATIONALE MA2263 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. TABLE 1 - FERRULE DIMENSIONS IN MM AND WEIGHT

6、IN KGFIGURE 1 - SLEEVE FERRULE SWAGEDAEROSPACE STANDARD MA2263 SHEET 2 OF 2 FERRULE, SLEEVE, BUTT WELD, THREADLESS, COUPLING, FLEXIBLE, FIXED CAVITY, SELF-BONDING, METRIC NOTES:/1/ MATERIAL: a. CODE “A” - 2024-T6 OR T851 ALUMINUM ALLOY PER QQ-A-225/6 OR 2024-T81 OR T8510 ALUMINUM ALLOY PER QQ-A-200/

7、3b. CODE “C” - 17-4PH CORROSION RESISTING STEEL, COND. H1075, PER AMS 5643 OR 15-5PH CORROSION RESISTING STEEL, COND. H1150, PER AMS 5659c. CODE “T” - 6AL-4V TITANIUM ALLOY PER MIL-T-9047 OR AMS 49282. FINISH: a. MATERIAL CODE “A” - CHEMICAL CONVERSION COAT PER MIL-C-5541, CLASS 3b. MATERIAL CODE “C

8、” - PASSIVATE PER QQ-P-35c. MATERIAL CODE “T” - NONE/3/ THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY (SEE MA2242). USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS./4/ IDENTIFICATION: INK STAMP

9、, 1.58 mm OR LARGER LETTERS, WITH THE FOLLOWING MINIMUM INFORMATION: MANUFACTUERS NAME, TRADEMARK OR CAGE NUMBER, COMPLETE “MA” NUMBER, AND DATE OF MANUFACTURE IN QUARTERS (1Q91 - FIRST QUARTER 1991). SIZES 18 AND SMALLER MAY BE INDIVIDUALLY BAGGED WITH A TAG CONTAINING THE ABOVE INFORMATION.5. RATE

10、D OPERATING CHARACTERISTICS: SEE MA2241./6/ SPECIFIC DIMENSIONS AND TOLERANCES ARE SPECIFIED AND CONTROLLED BY THE SUPPLIER. THE SUPPLIER IS RESPONSIBLE TO ENSURE COMPATIBILITY WITH THE ASSEMBLY AND COMPLIANCE WITH THE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION.7. TUBING SIZES ARE PER ISO 2964-19

11、74 EXCEPT AS NOTED./8/ THESE FERRULES FIT COUPLING ASSEMBLIES THAT USE NONSTANDARD TUBING DIAMETERS.9. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 3.2 m Ra.10. BREAK EDGES 0.08 TO 0.38 UNLESS OTHERWISE SPECIFIED.11. DIMENSIONING AND TOLERANCING: ANSI Y14.5M.12. DIMENSIONS IN MILLIMETERS, UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS 0.13, ANGULAR DIMENSIONS 0.5.13. EXAMPLE OF PART NUMBER: