SAE J 2956-2016 Occupant Restraint and Equipment Mounting Integrity C Side Impact Ambulance Patient Compartment.pdf

《SAE J 2956-2016 Occupant Restraint and Equipment Mounting Integrity C Side Impact Ambulance Patient Compartment.pdf》由会员分享，可在线阅读，更多相关《SAE J 2956-2016 Occupant Restraint and Equipment Mounting Integrity C Side Impact Ambulance Patient Compartment.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/J2956_201608SURFACE VEHICLERECOMMENDED PRACTICEJ2956 AUG2016Issued 2011-06Revised 2016-08Supe

5、rseding J2956 JUN2011Occupant Restraint and Equipment Mounting Integrity Side Impact Ambulance Patient CompartmentRATIONALEThis revision updates the titling to eliminate the term “System-Level” from the document. It adds a reference to SAE J1727 in section 2.1.1, data processing in accordance with S

6、AE J1727 in section 5, and adds a requirement to utilize SAE J211-2 in section 6, Photographic Instrumentation. Further, it expands section 4 to allow component-level testing in addition to system-level testing to be consistent with changes made to SAE J2418. Finally, it provides additional referenc

7、es in section 2.2 which describe the testing used to develop the pulse curves described in section 4.2.1. SCOPEThis SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applicatio

8、ns. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are inc

9、luded.2. REFERENCES2.1 Applicable DocumentsThe following publications form a part of the specification to the extent specified herein. Unless otherwise indicated, the latest revision of SAE publications shall apply.2.1.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warre

10、ndale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.SAE J211-1 Instrumentation for Impact Test - Part 1: Electronic InstrumentationSAE J211-2 Instrumentation for Impact Test - Part 2: Photographic InstrumentationSAE J1727 Calculation Guidelin

11、es for Impact TestingSAE Engineering Aid 23 “Users Manual for the 50th-Percentile Hybrid-III Test Dummy,” June 1985SAE INTERNATIONAL J2956 AUG2016 Page 2 of 42.2 Other PublicationsCode of Federal Regulations, Title 49, Part 571.208. Occupant Crash Protection.Code of Federal Regulations, Title 49, Pa

12、rt 571.214. Side Impact Protection.Code of Federal Regulations, Title 49, Part 572. Anthropomorphic Test Devices.Current, R., Moore, P., Green, J., Yannaccone, J. et al., “Crash Testing of Ambulance Chassis Cab Vehicles,“ SAE Technical Paper 2007-01-4267, 2007, doi:10.4271/2007-01-4267IIHS Side Impa

13、ct 2001 Ford E-350 Type II Ambulance, Curb Side, Published by NTIS #PB2013102946IIHS Side Impact 2001 Ford E-350 Type II Ambulance, Street Side, Published by NTIS #PB2013102947IIHS Side Impact 2006 Ford F450 Type III Ambulance, Curb Side, Published by NTIS #PB2013102948IIHS Side Impact 2006 Ford F45

14、0 Type III Ambulance, Street Side, Published by NTIS #PB20131029493. ANTHROPOMORPHIC TEST DEVICESFor the dynamic tests described in the following sections, restraint systems should be evaluated with the aid of anAnthropomorphic Test Device (ATD). The ATD should be of a type that will closely represe

15、nt the size, weight, and articulation characteristics of a 50th percentile male in a seated position. Examples of such an ATD include the Hybrid-III and Euro SID2 with rib extensions 50th percentile male ATD. The ATD should be selected appropriately based on the orientation of the seat relative to t

16、he direction of travel and the purpose of the test. The physical characteristics of these ATDs are described in 49 CFR 572 subparts E and U.Applicable measurement capabilities of the Hybrid-III 50th percentile male ATD are described in 49 CFR 571.208 and applicable measurement capabilities of the Eu

17、ro SID2-re 50th percentile male ATD are described in 49 CFR 571.214.ATDs of other sizes (i.e., 95th-percentile male, 5th-percentile female, etc.) may be used to evaluate restraint system performance for various occupant sizes.4. DYNAMIC SLED TESTSFor component-level restraint system tests, only the

18、subject seat or patient cot, and associated restraint system hardware are installed on the test sled fixture. No other patient compartment components need to be installed on the test sled fixture. Proper restraint anchorage geometry, relative to the seat or patient cot, should be maintained. Tethers

19、 should be set according to the manufacturers specifications. The primary purpose of component-level testing is to evaluate seat or patient cot structural integrity, restraint component performance and occupant excursion when subjected to vehicle deceleration from a representative side impact crash

20、pulse. Component-level testing is also appropriate to evaluate equipment mounting system integrity and cabinet content retention.For system-level restraint system tests, all interior patient compartment components that are potential occupant contact surfaces (cabinets, countertops, patient cots) sha

21、ll be installed on the test sled where practical. Proper geometry relative to the components being tested should be maintained. Wherever practicable, actual production components should be used. If not, components with performance characteristics near those expected for production should be used. Se

22、at or patient cot tethers should be set according to the manufacturers specifications. The primary purpose of system-level testing is to evaluate restraint system performance, seat or patient cot structural integrity, occupant excursion, equipment mounting integrity, and occupant interaction with in

23、terior components when subjected to a representative side impact crash pulse.4.1 Test FixtureFor the side impact tests, a sled fixture mounted on a uni-directional tracking system is required. Typical sled fixture systems are of the deceleration and acceleration types. For the deceleration system, t

24、he sled fixture is accelerated to a desired speed and then decelerated through the programmed pulse via energy-absorbing methods (i.e., honeycomb, extruded steel rods, etc.). For the acceleration system, the programmed pulse is applied as a rearward acceleration to the sled fixture, which is initial

25、ly at rest.SAE INTERNATIONAL J2956 AUG2016 Page 3 of 44.2 Side Impact Sled Pulse SpecificationFor side impact tests, a sled deceleration pulse is applied perpendicular to the vehicle longitudinal axis. The pulse profilemust fall within the corridor delineated by the plots in Figure 1 and the values

26、in Table 1. Total velocity change during the test shall be 15 mph 1 mph.Figure 1 - Dynamic sled corridorTable 1 - Dynamic sled corridor break pointsPositionTime(sec)Acceleration (g) PositionTime(sec)Acceleration (g)A 0 -5.0 F 0.005 0.0B 0.009 -26.0 G 0.016 -19.0C 0.036 -26.0 H 0.029 -19.0D 0.045 -10

27、.0 I 0.035 0.0E 0.055 -10.04.3 Anthropomorphic Test Device (ATD) PositioningATD positioning procedures for this testing should be consistent with the positioning procedures outlined in 49 CFR 571.208 and 49 CFR 571.214, where practicable.0 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 0.055

28、Time s-35-30-25-20-15-10-50Acceleration gAB CD EFG HISAE INTERNATIONAL J2956 AUG2016 Page 4 of 45. INSTRUMENTATIONTo record the deceleration pulse accelerometers may be mounted to the sled fixture. ATD instrumentation may include any of the measurements mentioned in Section 3. Dynamic seat belt load

29、s may be recorded by installing webbing load transducers on the seat belts. All measurements should be recorded, filtered and processed according to the most recent version of SAE J211-1 and SAE J1727.6. PHOTOGRAPHIC INSTRUMENTATIONHigh-speed cameras should be used to document the dynamic tests. The

30、 field of view of these cameras should be large enough to document the entire range of motion of the ATD and/or mounted equipment during the deceleration event. Wherever possible, off-board cameras should be used to allow for the use of longer focal-length lenses and, therefore, less lens distortion

31、 error when performing analysis of the high-speed footage. If complete coverage of occupant kinematics is not possible with off-board cameras only, the use of on-board cameras will be required.Each high-speed camera should operate at a frame rate sufficient to facilitate motion analysis of the film.

32、 A minimum frame rate of 500 frames per second is recommended. Sufficient reference targets, both stationary and on the test sled/fixture and ATD, should be provided. Provisions should be made for synchronizing electronic and photographic instrumentation. Wherever possible, the cameras should be mou

33、nted such that they are perpendicular to the axis of motion. All video shallbe captured and processed according to the most recent version of SAE J211-2.7. NOTES7.1 Revision IndicatorA change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revi

34、sions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.PREPARED BY THE SAE TRUCK AND BUS CRASHWORTHINESS COMMITTEE OF THESAE TRUCK AND BUS BODY AND OCCUPANT ENVIRONMENT STEERING COMMITTEE