SAE J 592-2016 Sidemarker Lamps for Use on Road Vehicles Less than 2032 mm in Overall Width.pdf

《SAE J 592-2016 Sidemarker Lamps for Use on Road Vehicles Less than 2032 mm in Overall Width.pdf》由会员分享，可在线阅读，更多相关《SAE J 592-2016 Sidemarker Lamps for Use on Road Vehicles Less than 2032 mm in Overall Width.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/J592_201609SURFACE VEHICLESTANDARDJ592 SEP2016Issued 1937-01Revised 2016-09Superseding J592 M

5、AR2009Sidemarker Lamps for Use on Road Vehicles Less than 2032 mm in Overall WidthRATIONALE6.1.5.2 Reference to Figure 3 added to provide clarification for how alternate inboard test angle is calculated.Figure 3 addedxSection 2.2.2 revised.xSection 6.1.5.2 chaged 4.6m to 4.57m for more accurate roun

6、ding, to be consistent with FMVSS108 and CMVSS108, 15 foot = 4.572mxSection 6.4.2 revised1. SCOPEThis SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.2. REFERENCES2.1 Applicable DocumentsThe following publicatio

7、ns form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply.2.1.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1

8、 724-776-4970 (outside USA), www.sae.org.SAE J567 Lamp Bulb Retention SystemSAE J575 Test Methods and Equipment for Lighting Devices and Components for Use on Vehicles Less than 2032 mm in Overall WidthSAE J576 Plastic Material or Materials for Use in Optical Parts Such as Lenses and Reflex Reflecto

9、rs of Motor Vehicle Lighting DevicesSAE J578 Color SpecificationSAE INTERNATIONAL J592 SEP2016 Page 2 of 7SAE J759 Lighting Identification CodeSAE J1889 L.E.D. Signal and Marking Lighting DevicesSAE J2042 Clearance, Sidemarker, and Identification Lamps for Use on Motor Vehicles 2032 mm or More in Ov

10、erall WidthSAE J2139 Tests for Signal and Marking Devices Used on Vehicles 2032 mm or More in Overall Width2.2 Related PublicationsThe following publications are provided for information purposes only and are not a required part of this SAE Technical Report.2.2.1 SAE PublicationsAvailable from SAE I

11、nternational, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.SAE J387 Terminology - Motor Vehicle LightingSAE J2442 Harmonized Provisions for Installation of Lamps and Retro- Reflecting Devices on Road Vehicl

12、es Except Motorcycles2.2.2 FMVSS PublicationsAvailable from the Superintendent of Documents, U. S. Government Printing Office, Mail Stop: SSOP, Washington, DC20402-9320, http:/www.gpo.gov/fdsys/browse/collectionCfr.action?collectionCode=CFR.CFR Title 49 Part 571.108 Lamps, Reflective Devices and Ass

13、ociated Equipment (FMVSS108)2.2.3 CMVSS PublicationsAvailable from Transport Canada, Motor Vehicle Safety, P.O. Box 8880, Ottawa Post Terminal, Ottawa, Ontario, K1G.3J2 or at www.tc.gc.ca.Canada Motor Vehicle Safety Standard (CMVSS) 108 Lighting Systems and Retro Reflective Devices3. DEFINITIONS3.1

14、SIDEMARKER LAMPSLighting devices used to indicate the presence and length of the vehicle when viewed from the side.4. LIGHTING IDENTIFICATION CODESidemarker lamps which meet the requirements of this document may be identified by the code “P2” in accordance with SAE J759.SAE INTERNATIONAL J592 SEP201

15、6 Page 3 of 75. TESTS5.1 SAE J575 and SAE J1889 are a part of this document. The following tests are applicable with the modifications as indicated. Alternatively, sidemarker lamps may be tested according to SAE J2139.5.1.1 Vibration5.1.2 Moisture5.1.3 Dust5.1.4 Corrosion5.1.5 Photometry5.1.5.1 The

16、photometric tests shall be made at a distance of at least 3 m between the lighting device and the photometer.5.1.5.2 The H-V axis of a sidemarker lamp in a position as it will be mounted on a vehicle shall be taken as perpendicular to a vertical plane passing through the longitudinal axis of the veh

17、icle.5.1.6 Warpage5.2 ColorSAE J578 is a part of this document.5.3 Plastic MaterialsSAE J576 is part of this document.6. REQUIREMENTS6.1 Performance RequirementsThe device when tested in accordance with the test procedures of this document shall meet the requirements of SAE J575 and, if applicable,

18、SAE J1889. Alternatively, if tested according to SAE J2139, sidemarker lamps shall meet the requirements of SAE J2139.NOTE: Sidemarkers conforming to requirements of SAE J2042 meet requirements of SAE J592.6.1.1 Vibration6.1.2 Moisture6.1.3 Dust6.1.4 Corrosion6.1.5 Photometry6.1.5.1 The lamp shall b

19、e designed to conform to the zone total photometric requirements of Figures 1 and 2. The summation of the luminous intensity measurements at the test points in a zone shall be at least the value shown.6.1.5.2 The inboard angle requirements for sidemarkers may be met alternatively for inboard test po

20、ints at a distance of 4.57 m from the vehicle on a vertical plane that is perpendicular to the longitudinal axis of the vehicle and located midway between the front and rear sidemarker lamps, reference Figure 3.SAE INTERNATIONAL J592 SEP2016 Page 4 of 76.1.6 Warpage6.2 Color6.2.1 The color of light

21、from front and intermediate sidemarker lamps shall be yellow per SAE J578.6.2.2 The color of light from rear sidemarker lamps shall be red per SAE J578.6.3 Plastic Materials RequirementsPlastic materials used in optical parts shall meet the requirements of SAE J576.Figure 1 - Photometric requirement

22、s (red)minimum luminous intensity (cd)SAE INTERNATIONAL J592 SEP2016 Page 5 of 7Figure 2 - Photometric requirements (yellow)minimum luminous intensity (cd)Figure 3 Alternate inboard test angle calculationSAE INTERNATIONAL J592 SEP2016 Page 6 of 76.4 Design Requirements6.4.1 A sidemarker lamp may be

23、an independent lamp or grouped, combined, or reciprocally incorporated with any other lamp or reflective device if the requirements for sidemarker lamp and the associated equipment are met.6.4.2 If a sidemarker lamp is reciprocally incorporated or combined with a turn signal lamp or a stop lamp and

24、a replaceable multi-mode light source (such as a 2-filament bulb) is used, the light source retention system shall have an indexing feature to exclude any light source without the indexing feature. Moreover, removable light source retention systems (sockets) shall have an indexing feature so that th

25、ey cannot be installed in the lamp housing in a random orientation, unless the lamp will perform all of its intended functions properly with random light source orientation.6.5 Installation Requirements6.5.1 As installed on the vehicle, with all vehicular obstructions considered, sidemarker lamps, s

26、hall meet photometric requirements of Figures 1 and 2.6.5.2 Sidemarker lamps shall be mounted on the permanent structure of the vehicle not less than 380 mm above the road surface measured from the center of the device at the vehicle curb weight.6.5.3 Sidemarker lamps shall be mounted as near as pra

27、cticable to the front and rear edges of the vehicles to indicate the overall length of the vehicle.6.5.4 Intermediate yellow sidemarker lamps shall be mounted near the midpoint on vehicles 7.6 m or more in overall length.7. GUIDELINES7.1 Installation GuidelinesThe following guidelines apply to sidem

28、arker lamps as used on the vehicle and shall not be considered part of the requirements.7.1.1 The luminous intensity of a lighting device may vary with applied voltage. The electrical wiring in the vehicle should be adequate to supply design voltage to the light source of a lighting device.7.1.2 Per

29、formance of lighting device may deteriorate significantly as a result of dirt, grime, ice, and/or snow accumulation on its optical surfaces. Installation of a device on a vehicle should be considered to minimize the effect of these factors.7.1.3 Where it is expected that lighting device must perform

30、 in extremely severe environments, such as in off- highway, mining, fuel haulage, or where it is expected that they will be totally immersed in water, the user should specify lamps specifically designed for such use.7.2 Socket Design GuidelineFor requirements and gages to be used in socket design, r

31、efer to SAE J567.SAE INTERNATIONAL J592 SEP2016 Page 7 of 78. NOTES8.1 Revision IndicatorA change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) sy

32、mbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.PREPARED BY THE SAE SIGNAL AND MARKING DEVICES SUBCOMMITTEE OF THE SAE LIGHTING COMMITTEE