SAE AS 6471-2017 FITTING ASSEMBLY TEE FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN EXTERNAL SWAGE ON BRANCH HYDRAULIC.pdf

《SAE AS 6471-2017 FITTING ASSEMBLY TEE FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN EXTERNAL SWAGE ON BRANCH HYDRAULIC.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6471-2017 FITTING ASSEMBLY TEE FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN EXTERNAL SWAGE ON BRANCH HYDRAULIC.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC AS6471Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mean

2、s, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org IS

3、SUED2017-03THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS6471 SHEET 1 OF 7 PROCUREMENT SPECIFICATION: AS4459 /6/ SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvance the state oftechnicaland engineering sciences. The use of this report isent

4、irely voluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAEreviews eachtechnical reportatleast every fiveyears atwhich time itmay be revised, reaffirmed, stabilized,orcancelled. SAE invites yo

5、urwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS6471 RATIONALE NEW STANDARD FOR OPERATING PRESSURES UP TO AND INCLUDING 3000 PSI. FIGURE 1 - TEE ADAPTER ASSEMBLY, SWIVEL NUT TO EXTERNAL SWAGE ON RUN, EXTERNA

6、L SWAGE ON BRANCH AEROSPACE STANDARD AS6471 SHEET 2 OF 7 FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC TABLE 1 TABLE 1A - DIMENSIONS A THROUGH D2 BASIC NO. AS6471 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE

7、END 3 A .015 B C (D1) /19/ (D2) /19/ 040404 .250 .250 .250 .877 1.118-1.148 1.142-1.172 .615 .615 050505 .3125 .3125 .3125 .921 1.180-1.210 1.248-1.278 .655 .655 060404 .375 .250 .250 1.134 1.205-1.235 1.277-1.307 .615 .615 060406 .375 .250 .375 1.134 1.205-1.235 1.287-1.317 .615 .690 060604 .375 .3

8、75 .250 1.134 1.190-1.220 1.277-1.307 .690 .615 060606 .375 .375 .375 1.035 1.269-1.299 1.283-1.313 .690 .690 060806 .375 .500 .375 1.337 1.799-1.829 1.381-1.411 1.193 .690 080408 .500 .250 .500 1.331 1.209-1.239 2.150-2.180 .615 1.193 080606 .500 .375 .375 1.331 1.323-1.353 1.381-1.411 .690 .690 08

9、0608 .500 .375 .500 1.331 1.323-1.353 2.150-2.180 .690 1.193 080804 .500 .500 .250 1.331 1.799-1.829 1.325-1.355 1.193 .615 080806 .500 .500 .375 1.331 1.799-1.829 1.381-1.411 1.193 .690 080808 .500 .500 .500 1.316 1.784-1.814 1.810-1.840 1.193 1.193 080810 .500 .500 .625 1.411 1.879-1.909 1.945-1.9

10、75 1.193 1.233 081008 .500 .625 .500 1.411 1.860-1.890 2.150-2.180 1.233 1.193 081208 .500 .750 .500 1.498 1.990-2.020 2.150-2.180 1.303 1.193 081212 .500 .750 .750 1.498 1.990-2.020 2.250-2.280 1.303 1.303 081216 .500 .750 1.000 1.822 2.187-2.217 2.418-2.448 1.303 1.448 081616 .500 1.000 1.000 1.84

11、3 2.468-2.498 2.468-2.498 1.448 1.448 100610 .625 .375 .625 1.536 1.344-1.374 2.275-2.305 .690 1.233 100806 .625 .500 .375 1.536 1.879-1.909 1.443-1.473 1.193 .690 101004 .625 .625 .250 1.536 1.860-1.890 1.387-1.417 1.233 .615 101006 .625 .625 .375 1.536 1.860-1.890 1.527-1.557 1.233 .690 101010 .62

12、5 .625 .625 1.536 1.860-1.890 2.275-2.305 1.233 1.233 101210 .625 .750 .625 1.536 1.990-2.020 1.932-1.962 1.303 1.233 121010 .750 .625 .625 1.843 1.932-1.962 1.932-1.962 1.233 1.233 121012 .750 .625 .750 1.843 1.990-2.020 2.250-2.280 1.233 1.303 121206 .750 .750 .375 1.843 1.990-2.020 1.670-1.700 1.

13、303 .690 121212 .750 .750 .750 1.560 1.990-2.020 2.657-2.687 1.303 1.303 121604 .750 1.000 .250 1.843 2.468-2.498 1.652-1.682 1.448 .615 121616 .750 1.000 1.000 1.843 2.468-2.498 2.468-2.498 1.448 1.448 160812 1.000 .500 .750 1.716 2.344-2.374 2.390-2.420 1.193 1.303 161208 1.000 .750 .500 1.716 2.3

14、60-2.390 2.279-2.309 1.303 1.193 161212 1.000 .750 .750 1.716 2.360-2.690 2.360-2.390 1.303 1.303 161604 1.000 1.000 .250 1.716 2.344-2.374 1.652-1.682 1.448 .615 161606 1.000 1.000 .375 1.716 2.344-2.374 1.835-1.865 1.448 .690 161608 1.000 1.000 .500 1.716 2.344-2.374 2.279-2.309 1.448 1.193 161610

15、 1.000 1.000 .625 1.716 2.344-2.374 2.279-2.309 1.448 1.233 161612 1.000 1.000 .750 1.716 2.344-2.374 2.360-2.390 1.448 1.303 161616 1.000 1.000 1.000 1.716 2.344-2.374 2.715-2.745 1.448 1.448 202010 1.250 1.250 .625 2.006 2.684-2.714 2.778-2.808 1.550 1.233 202012 1.250 1.250 .750 2.006 2.684-2.714

16、 2.778-2.808 1.550 1.303 242010 1.500 1.250 .625 2.715 2.684-2.714 2.765-2.795 1.550 1.233 242012 1.500 1.250 .750 2.715 2.684-2.714 2.765-2.795 1.550 1.303 AEROSPACE STANDARD AS6471 SHEET 3 OF 7 FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC TA

17、BLE 1B - DIMENSIONS E1 THROUGH H BASIC NO. AS6471 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 E1 +.000 -.003 /18/ E2 +.000 -.003 /18/ F1 /3/ F2 /3/ G (H) 040404 .250 .250 .250 .338 .338 .257-.260 .257-.260 .375-.405 .563 050505 .3125 .3125 .3125 .413 .413 .

18、319-.322 .319-.322 .450-.480 .625 060404 .375 .250 .250 .338 .338 .257-.260 .257-.260 .530-.560 .688 060406 .375 .250 .375 .338 .480 .257-.260 .382-.385 .530-.560 .688 060604 .375 .375 .250 .480 .338 .382-.385 .257-.260 .530-.560 .688 060606 .375 .375 .375 .480 .480 .382-.385 .382-.385 .530-.560 .68

19、8 060806 .375 .500 .375 .655 .480 .508-.511 .382-.385 .690-.720 .688 080408 .500 .250 .500 .338 .655 .257-.260 .508-.511 .690-.720 .875 080606 .500 .375 .375 .480 .480 .382-.385 .382-.385 .690-.720 .875 080608 .500 .375 .500 .480 .655 .382-.385 .508-.511 .690-.720 .875 080804 .500 .500 .250 .655 .33

20、8 .508-.511 .257-.260 .690-.720 .875 080806 .500 .500 .375 .655 .480 .508-.511 .382-.385 .690-.720 .875 080808 .500 .500 .500 .655 .655 .508-.511 .508-.511 .690-.720 .875 080810 .500 .500 .625 .655 .787 .508-.511 .633-.636 .846-.876 .875 081008 .500 .625 .500 .787 .655 .633-.636 .508-.511 .846-.876

21、.875 081208 .500 .750 .500 .929 .655 .758-.761 .508-.511 1.021-1.051 .875 081212 .500 .750 .750 .929 .929 .758-.761 .758-.761 1.021-1.051 .875 081216 .500 .750 1.000 .929 1.257 .758-.761 1.008-1.011 1.365-1.395 .875 081616 .500 1.000 1.000 1.257 1.257 1.008-1.011 1.008-1.011 1.365-1.395 .875 100610

22、.625 .375 .625 .480 .787 .382-.385 .633-.636 .846-.876 1.000 100806 .625 .500 .375 .655 .480 .508-.511 .382-.385 .846-.876 1.000 101004 .625 .625 .250 .787 .338 .633-.636 .257-.260 .846-.876 1.000 101006 .625 .625 .375 .787 .480 .633-.636 .382-.385 .846-.876 1.000 101010 .625 .625 .625 .787 .787 .63

23、3-.636 .633-.636 .846-.876 1.000 101210 .625 .750 .625 .929 .787 .758-.761 .633-.636 1.021-1.051 1.000 121010 .750 .625 .625 .787 .787 .633-.636 .633-.636 1.021-1.051 1.250 121012 .750 .625 .750 .787 .929 .633-.636 .758-.761 1.021-1.051 1.250 121206 .750 .750 .375 .929 .480 .758-.761 .382-.385 1.021

24、-1.051 1.250 121212 .750 .750 .750 .929 .929 .758-.761 .758-.761 1.021-1.051 1.250 121604 .750 1.000 .250 1.257 .338 1.008-1.011 .257-.260 1.365-1.395 1.250 121616 .750 1.000 1.000 1.257 1.257 1.008-1.011 1.008-1.011 1.365-1.395 1.250 160812 1.000 .500 .750 .655 .929 .508-.511 .758-.761 1.365-1.395

25、1.500 161208 1.000 .750 .500 .929 .655 .758-.761 .508-.511 1.365-1.395 1.500 161212 1.000 .750 .750 .929 .929 .758-.761 .758-.761 1.365-1.395 1.500 161604 1.000 1.000 .250 1.257 .338 1.008-1.011 .257-.260 1.365-1.395 1.500 161606 1.000 1.000 .375 1.257 .480 1.008-1.011 .382-.385 1.365-1.395 1.500 16

26、1608 1.000 1.000 .500 1.257 .655 1.008-1.011 .508-.511 1.365-1.395 1.500 161610 1.000 1.000 .625 1.257 .787 1.008-1.011 .633-.636 1.365-1.395 1.500 161612 1.000 1.000 .750 1.257 .929 1.008-1.011 .758-.761 1.365-1.395 1.500 161616 1.000 1.000 1.000 1.257 1.257 1.008-1.011 1.008-1.011 1.365-1.395 1.50

27、0 202010 1.250 1.250 .625 1.489 .787 1.258-1.262 .633-.636 1.677-1.707 1.812 202012 1.250 1.250 .750 1.489 .929 1.258-1.262 .758-.761 1.677-1.707 1.812 242010 1.500 1.250 .625 1.489 .787 1.258-1.262 .633-.636 1.865-1.895 2.125 242012 1.500 1.250 .750 1.489 .929 1.258-1.262 .758-.761 1.865-1.895 2.12

28、5 AEROSPACE STANDARD AS6471 SHEET 4 OF 7 FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC TABLE 1C - THREAD, DIMENSIONS K THROUGH V2 AND WEIGHTS BASIC NO. AS6471 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END

29、3 K MAX N GAGE (T) THREAD PER AS8879 V1 /3/ V2 /3/ WEIGHT APPROX LB/EA CRES WEIGHT APPROX LB/EA TI WEIGHT APPROX LB/EA AL 040404 .250 .250 .250 .241 .2930 .4375-20 UNJF-3B .190-.240 .190-.240 .067 .036 .024 050505 .3125 .3125 .3125 .325 .3500 .5000-20 UNJF-3B .200-.250 .200-.250 .102 .057 .036 06040

30、4 .375 .250 .250 .295 .4120 .5625-18 UNJF-3B .190-.240 .190-.240 .116 .064 .040 060406 .375 .250 .375 .295 .4120 .5625-18 UNJF-3B .190-.240 .220-.270 .117 .065 .041 060604 .375 .375 .250 .295 .4120 .5625-18 UNJF-3B .220-.270 .190-.240 .116 .064 .040 060606 .375 .375 .375 .295 .4120 .5625-18 UNJF-3B

31、.220-.270 .220-.270 .114 .063 .040 060806 .375 .500 .375 .295 .4120 .5625-18 UNJF-3B .410-.435 .220-.270 .193 .109 .067 080408 .500 .250 .500 .310 .5600 .7500-16 UNJF-3B .190-.240 .410-.435 .237 .132 .082 080606 .500 .375 .375 .310 .5600 .7500-16 UNJF-3B .220-.270 .220-.270 .209 .116 .073 080608 .50

32、0 .375 .500 .310 .5600 .7500-16 UNJF-3B .220-.270 .410-.435 .245 .137 .085 080804 .500 .500 .250 .310 .5600 .7500-16 UNJF-3B .410-.435 .190-.240 .225 .125 .078 080806 .500 .500 .375 .310 .5600 .7500-16 UNJF-3B .410-.435 .220-.270 .226 .126 .078 080808 .500 .500 .500 .310 .5600 .7500-16 UNJF-3B .410-

33、.435 .410-.435 .240 .134 .083 080810 .500 .500 .625 .310 .5600 .7500-16 UNJF-3B .410-.435 .410-.435 .317 .178 .110 081008 .500 .625 .500 .310 .5600 .7500-16 UNJF-3B .410-.435 .410-.435 .341 .192 .118 081208 .500 .750 .500 .310 .5600 .7500-16 UNJF-3B .365-.390 .410-.435 .435 .246 .151 081212 .500 .75

34、0 .750 .310 .5600 .7500-16 UNJF-3B .365-.390 .365-.390 .441 .250 .153 081216 .500 .750 1.000 .310 .5600 .7500-16 UNJF-3B .365-.390 .325-.350 .825 .471 .286 081616 .500 1.000 1.000 .310 .5600 .7500-16 UNJF-3B .325-.350 .325-.350 .851 .486 .295 100610 .625 .375 .625 .418 .6730 .8750-14 UNJF-3B .220-.2

35、70 .410-.435 .360 .200 .125 100806 .625 .500 .375 .418 .6730 .8750-14 UNJF-3B .410-.435 .220-.270 .342 .190 .119 101004 .625 .625 .250 .418 .6730 .8750-14 UNJF-3B .410-.435 .190-.240 .333 .185 .116 101006 .625 .625 .375 .418 .6730 .8750-14 UNJF-3B .410-.435 .220-.270 .344 .191 .119 101010 .625 .625

36、.625 .418 .6730 .8750-14 UNJF-3B .410-.435 .410-.435 .384 .214 .133 101210 .625 .750 .625 .418 .6730 .8750-14 UNJF-3B .365-.390 .410-.435 .421 .235 .146 121010 .750 .625 .625 .382 .8100 1.0625-12 UNJ-3B .410-.435 .410-.435 .548 .297 .191 121012 .750 .625 .750 .382 .8100 1.0625-12 UNJ-3B .410-.435 .3

37、65-.390 .593 .323 .206 121206 .750 .750 .375 .382 .8100 1.0625-12 UNJ-3B .365-.390 .220-.270 .566 .307 .197 121212 .750 .750 .750 .382 .8100 1.0625-12 UNJ-3B .365-.390 .365-.390 .558 .303 .194 121604 .750 1.000 .250 .382 .8100 1.0625-12 UNJ-3B .325-.350 .190-.240 .894 .496 .310 121616 .750 1.000 1.0

38、00 .382 .8100 1.0625-12 UNJ-3B .325-.350 .325-.350 .915 .509 .318 160812 1.000 .500 .750 .448 1.0620 1.3125-12 UNJ-3B .410-.435 .365-.390 1.008 .555 .350 161208 1.000 .750 .500 .448 1.0620 1.3125-12 UNJ-3B .365-.390 .410-.435 .986 .543 .342 161212 1.000 .750 .750 .448 1.0620 1.3125-12 UNJ-3B .365-.3

39、90 .365-.390 .974 .536 .338 161604 1.000 1.000 .250 .448 1.0620 1.3125-12 UNJ-3B .325-.350 .190-.240 .882 .483 .306 161606 1.000 1.000 .375 .448 1.0620 1.3125-12 UNJ-3B .325-.350 .220-.270 .925 .508 .321 161608 1.000 1.000 .500 .448 1.0620 1.3125-12 UNJ-3B .325-.350 .410-.435 .938 .515 .326 161610 1

40、.000 1.000 .625 .448 1.0620 1.3125-12 UNJ-3B .325-.350 .410-.435 .923 .507 .321 161612 1.000 1.000 .750 .448 1.0620 1.3125-12 UNJ-3B .325-.350 .365-.390 .932 .512 .324 161616 1.000 1.000 1.000 .448 1.0620 1.3125-12 UNJ-3B .325-.350 .325-.350 .983 .541 .341 202010 1.250 1.250 .625 .459 1.3160 1.6250-

41、12 UNJ-3B .325-.350 .410-.435 1.694 .937 .589 202012 1.250 1.250 .750 .459 1.3160 1.6250-12 UNJ-3B .325-.350 .365-.390 1.639 .906 .570 242010 1.500 1.250 .625 .454 1.5650 1.8750-12 UNJ-3B .325-.350 .410-.435 2.428 1.339 .844 242012 1.500 1.250 .750 .454 1.5650 1.8750-12 UNJ-3B .325-.350 .365-.390 2.

42、386 1.315 .829 AEROSPACE STANDARD AS6471 SHEET 5 OF 7 FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC NOTES: /1/ MATERIALS: CODE LETTER “-“ BODY 21-6-9 STAINLESS STEEL PER AMS5656 NUT 304 STAINLESS STEEL PER AMS-QQ-S-763 WIRE 305 STAINLESS STEEL

43、PER ASTM A580/A580M CODE LETTER “E“ BODY COMMERCIALLY PURE TITANIUM PER AMS4921 NUT 6Al-4V TITANIUM PER AMS4928 WIRE 302 OR 305 STAINLESS STEEL PER ASTM A580/A580M CODE LETTER “D“ BODY 6061-T6 ALUMINUM ALLOY PER AMS4127 NUT 2024-T6 ALUMINUM ALLOY PER AMS-QQ-A-225/6 WIRE 2024-T4 OR T351 ALUMINUM ALLO

44、Y PER AMS-QQ-A-225. FOR SIZES 04 AND 05 WIRE MATERIAL TYPE 305 STAINLESS STEEL PER ASTM A580/A580M 2. FINISH: CODE LETTER “-“ BODY PASSIVATE THE WHOLE PART PER AMS2700 NUT PASSIVATION PER AMS2700 WIRE PASSIVATION PER AMS2700 CODE LETTER “E“ BODY NONE REQUIRED NUT FLUORIDE CONVERSION COAT PER AMS2486

45、 WIRE PASSIVATION PER AMS2700 CODE LETTER “D“ BODY CHEMICAL CONVERSION COAT ENTIRE PART (INCLUDING INTERNAL DIAMETERS) PER MIL-DTL-5541, CLASS 1A NUT ANODIZED WITH SEAL (YELLOW) PER MIL-A-8625 TYPE II CLASS 2 ALUMINUM WIRE ANODIZED WITH SEAL (YELLOW) PER MIL-A-8625 TYPE II CLASS 2, SIZES 06 AND LARG

46、ER CRES WIRE PASSIVATION PER AMS2700, SIZES 04 AND 05 AEROSPACE STANDARD AS6471 SHEET 6 OF 7 FITTING ASSEMBLY, TEE, FEMALE FLARELESS TO EXTERNAL SWAGE ON RUN, EXTERNAL SWAGE ON BRANCH, HYDRAULIC /3/ COATINGS/LUBRICANTS: CODE LETTER “-“ BODY a. LEAD FREE DRY FILM LUBRICANT PER AS5272 TYPE I b. POLYTE

47、TRAFLUOROETHYLENE (PTFE) COATING (GREEN) SHALL BE APPLIED TO BORE DIAMETER TO “V” DEPTH. OVERSPRAY ON /Y/ IS PERMITTED. OVERSPRAY IN GROOVE IS NOT PERMITTED. DIMENSION “F” APPLIES BEFORE PTFE COATING. c. A MINIMUM OF ONE GROOVE SHALL BE FILLED WITH ELASTOMERIC DIMETHYL SILOXANE COMPOUND NUT NONE REQ

48、UIRED WIRE LEAD FREE DRY FILM LUBRICANT PER AS5272 TYPE I CODE LETTER “E“ BODY a. LEAD FREE DRY FILM LUBRICANT PER AS5272 TYPE I b. POLYTETRAFLUOROETHYLENE (PTFE) COATING (BLACK) SHALL BE APPLIED TO EXTERIOR SURFACES EXCEPT /5/ AND TO BORE DIAMETER TO “V” DEPTH. OVERSPRAY ON /Y/ IS PERMITTED. OVERSPRAY IN GROOVE IS NOT PERMI