SAE AS 4663C-2017 FITTING UNION SHORT FLARELESS.pdf

《SAE AS 4663C-2017 FITTING UNION SHORT FLARELESS.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4663C-2017 FITTING UNION SHORT FLARELESS.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, UNION, SHORT FLARELESS AS4663Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, with

2、out the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-06 REAFFIRMED2004-07 REVISED2017-06THIRD ANGLE PROJECTION CUS

3、TODIAN: G-3/G-3B REV.CFEDERAL SUPPLY CLASS 4730 AS4663 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS18280 /4/ SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.The use ofthisreportisentirelyvoluntary,anditsapplicabili

4、tyandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAE reviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEinvitesyourwritten commentsandsuggestions.SAE values your input

5、. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS4663C RATIONALE ADDED CONDUCTIVE HIGH PURITY ALUMINUM COATING FOR ALUMINUM ALLOY FITTINGS. FIGURE 1 FITTING, UNION, SHORT FLARELESS TABLE 1 DIMENSIONS AND WEIGHTS BASIC NO. AS4663 /15/ SIZE CODE (NOMINAL TUBE SIZE

6、) T THREAD PER AS8879 CLASS 3A A H K LB/EA APPROX REF ALUM LB/EA APPROX REF CRES LB/EA APPROX REF TI 2020 1.250 1.5625-12 UNJ 1.301 1.615-1.630 1.605 .096 .266 .152 2424 1.500 1.8125-12 UNJ 1.364 1.865-1.880 1.855 .134 .370 .212 AEROSPACE STANDARD AS4663 SHEET 2 OF 3 REV. C FITTING, UNION, SHORT FLA

7、RELESS NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER T: TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928 b. CODE LETTER V: TYPE 15-5PH CORROSION RESISTANT STEEL

8、BAR PER AMS5659 c. CODE LETTER W: TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124 2. HEAT TREATMENT: a. MATERIAL CODE LETTER T: NONE b. MATERIAL CODE LETTER V: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 c. MATERIAL CODE LETTER W: NONE /3/ FINISH: a. MATERIAL CODE LETTER T - FLUORIDE PHOSPHATE CONVE

9、RSION COAT PER AMS2486 b. MATERIAL CODE LETTER V: (1) V CODE PARTS TO BE PASSIVATED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: PASSIVATE PER AMS2700 TYPE 2 OR 8. (2) V CODE PARTS TO BE CADMIUM PLATED ONLY WILL HAVE THE FINISH CODE LETTER “P” AFTE

10、R THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. c. MATERIAL CODE LETTER W: (1) W CODE PARTS TO BE ANODIZED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE ANODIZE PER AMS2472 OR MIL-A-8625, TYPE

11、 II, CLASS 2, DYE BROWN SIMILAR TO COLOR 10080 OF AMS-STD-595. (2) W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE CODE IN THE PART NUMBER. SEE PROCUREMENT SPECIFICATION FOR REQUIREMENTS. /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SP

12、ECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCA

13、TION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. MANUFACTURERS NAME, TRADEMARK OR CAGE CODE, BASIC PART NUMBER, AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNECTION SYSTEMS WITH NOMINAL OPERATING PRESSURES AS FOLLOWS: a. SIZES -20 AND -24

14、TITANIUM ALLOY AND CORROSION RESISTANT STEEL AT 3000 PSI b. SIZES -20 AND -24 ALUMINUM ALLOY AT 600 PSI NOTE: THIS IS A NON-REDUCER FITTING. FOR REDUCER FITTING SEE AS4680. /7/ FINISH CODE LETTER “P” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “V” PARTS THAT ARE TO BE CADMIUM PLATED. FIN

15、ISH CODE LETTER “V” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUM TO PROVIDE LOW ELECTRICAL CONTACT RESISTANCE. NO OTHER LETTERS ARE TO FOLLOW THE SIZE CODES. AEROSPACE STANDARD AS4663 SHEET 3 OF 3 REV. C FITTING, UNION, SHORT FLARE

16、LESS 8. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE R

17、EVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 9. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 10. INTERPRETATION OF DRAWING PER AS4296.

18、 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 12. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. 14. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5. /15/ EXAMPLE OF PART NUMBER: AS4663 V 20 20 PBA SIC PA RT NUMBER FINISH CODE LETTER /3/ /7/MA TERIA L CODE LETTER /1/SIZ E CODE, TUBE SIZ E OFPORT #1 IN .062 INCREMENTSSIZ E CODE, TUBE SIZ E OF PORT #2 IN .062 INCREMENTS