SAE AS 3236D-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK NICKEL ALLOY UNS N07718 185 KSI MIN 1900-32 UNJF-3A.pdf

《SAE AS 3236D-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK NICKEL ALLOY UNS N07718 185 KSI MIN 1900-32 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3236D-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK NICKEL ALLOY UNS N07718 185 KSI MIN 1900-32 UNJF-3A.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, NICKEL ALLOY, UNS N07718, 185 KSI MIN, .1900-32 UNJF-3A AS3236Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any fo

2、rm or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: htt

3、p:/www.sae.org ISSUED1980-07REAFFIRMED2007-06 REVISED2017-03 THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.D FEDERAL SUPPLY CLASS 5306 AS3236 SHEET 1 OF 3 REV. D PROCUREMENT SPECIFICATION: AS7466 SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandeng

4、ineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,s

5、tabilized,orcancelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS3236D RATIONALE DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, ADD NEW INVENTORY DISPOSITION NOTE, ADD “MINI

6、MUM“ TO FPI SENSITIVITY LEVEL REQUIREMENT, GENERAL EDITORIAL UPDATE. FIGURE 1 - BOLT AEROSPACE STANDARD AS3236 SHEET 2 OF 3 REV. D BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, NICKEL ALLOY, UNS N07718, 185 KSI MIN, .1900-32 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L N

7、 MIN M MAX APPROX MASS LB/100 PART NO. L N MIN M MAX APPROX MASS LB/100 AS3236-03 .302-.322 .025 .092 .59 AS3236-25 1.678-1.698 .936 1.058 1.52 AS3236-04 .365-.385 .025 .092 .63 AS3236-26 1.740-1.760 .998 1.120 1.56 AS3236-05 .428-.448 .025 .092 .69 AS3236-27 1.802-1.822 1.060 1.182 1.60 AS3236-06 .

8、490-.510 .025 .092 .72 AS3236-28 1.865-1.885 1.123 1.245 1.64 AS3236-07 .552-.572 .025 .092 .76 AS3236-29 1.928-1.948 1.186 1.308 1.68 AS3236-08 .615-.635 .025 .092 .80 AS3236-30 1.990-2.010 1.248 1.370 1.73 AS3236-09 .678-.698 .025 .092 .84 AS3236-31 2.115-2.135 1.373 1.495 1.82 AS3236-10 .740-.760

9、 .025 .120 .88 AS3236-32 2.240-2.260 1.498 1.620 1.90 AS3236-11 .802-.822 .060 .183 .92 AS3236-33 2.365-2.385 1.623 1.745 1.98 AS3236-12 .865-.885 .123 .245 .97 AS3236-34 2.490-2.510 1.748 1.870 2.07 AS3236-13 .928-.948 .186 .308 1.01 AS3236-35 2.615-2.635 1.873 1.995 2.15 AS3236-14 .990-1.010 .248

10、.370 1.05 AS3236-36 2.740-2.760 1.998 2.120 2.23 AS3236-15 1.052-1.072 .310 .432 1.09 AS3236-37 2.865-2.885 2.123 2.245 2.33 AS3236-16 1.115-1.135 .373 .495 1.14 AS3236-38 2.990-3.010 2.248 2.370 2.41 AS3236-17 1.178-1.198 .436 .558 1.18 AS3236-39 3.115-3.135 2.373 2.495 2.49 AS3236-18 1.240-1.260 .

11、498 .620 1.23 AS3236-40 3.240-3.260 2.498 2.620 2.57 AS3236-19 1.302-1.322 .560 .682 1.27 AS3236-41 3.365-3.385 2.623 2.745 2.66 AS3236-20 1.365-1.385 .623 .745 1.31 AS3236-42 3.490-3.510 2.748 2.870 2.74 AS3236-21 1.428-1.448 .686 .808 1.35 AS3236-43 3.615-3.635 2.873 2.995 2.82 AS3236-22 1.490-1.5

12、10 .748 .870 1.39 AS3236-44 3.740-3.760 2.998 3.120 2.92 AS3236-23 1.552-1.572 .810 .932 1.43 AS3236-45 3.865-3.885 3.123 3.245 3.00 AS3236-24 1.615-1.635 .873 .995 1.47 NOTES /1/ FOR PART NUMBERS AS3236-03 THROUGH AS3236-14, DATUM Z SHALL REPLACE DATUM Y. 2. MATERIAL: CORROSION AND HEAT RESISTANT N

13、ICKEL ALLOY PER AMS5662 (UNS N07718). 3. PROCUREMENT SPECIFICATION: AS7466. 4. FLUORESCENT PENETRANT INSPECTION BEFORE PLATING PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE

14、 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN INCHES. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPEC

15、IFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED 10. DO NOT USE UNASSIGNED PART NUMBERS. AEROSPACE STANDARD AS3236 SHEET 3 OF 3 REV. D BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, NICKEL ALLOY, UNS N07718, 185 KSI MIN, .1900-32 UNJF-3A 11. REVISION INDICATOR: A CHANGE BAR

16、 (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.