SAE AS 1300D-2014 PORT - RING LOCKED FLUID CONNECTION TYPE STANDARD DIMENSIONS FOR.pdf

《SAE AS 1300D-2014 PORT - RING LOCKED FLUID CONNECTION TYPE STANDARD DIMENSIONS FOR.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1300D-2014 PORT - RING LOCKED FLUID CONNECTION TYPE STANDARD DIMENSIONS FOR.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD PORT - RING LOCKED FLUID CONNECTION TYPE STANDARD DIMENSIONS FOR AS1300Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyin

2、g, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1975-08REAFFIRMED 2000-10 REVISED

3、 2014-12THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.DFEDERAL SUPPLY CLASS 4730AS1300SHEET 1 OF 3REV. DPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entir

4、elyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites y

5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1300DRATIONALE REVISED TO CLARIFY NOTE FOR MINIMUM BOSS DIAMETER AND TO UPDATE THE STANDARD. /2/+1-03232EKDETAIL Z.006 YMUNDERCUTWIDTHTYPE B /4/

6、VIEW SHOWING OPTIONAL UNDERCUTSAME AS DETAIL Z EXCEPT AS SHOWN/2/ LUNDERCUT20 TYPE A63AEROSPACE STANDARD AS1300SHEET 2 OF 3REV. DPORT - RING LOCKED FLUID CONNECTION TYPE STANDARD DIMENSIONS FOR TABLE 1A - THREADS AND DIMENSIONS A-E BASIC NO. AS1300/12/SIZE CODE (TUBE OD) T THREAD AMINBMINCDEAS8879CL

7、ASS-3B MINOR DIA MOD 02 .125 .2160-28UNJF .1827- .1857 .408 .50 .381- .384 .254- .256 .093 03 .188 .2500-28UNJF .2167- .2197 .478 .62 .448- .451 .286- .288 .093 04 .250 .3125-24UNJF .2734- .2764 .524 .68 .495- .498 .339- .341 .093 05 .312 .3750-24UNJF .3359- .3389 .635 .79 .601- .604 .401- .403 .093

8、 06 .375 .4375-20UNJF .3903- .3933 .710 .85 .675- .678 .464- .466 .108 08 .500 .5625-18UNJF .5099- .5129 .826 1.04 .784- .787 .582- .584 .108 10 .625 .6875-24UNJEF .6484- .6514 1.052 1.17 1.015-1.018 .725- .727 .108 12 .750 .8125-20UNJEF .7653- .7683 1.182 1.42 1.139-1.142 .899- .901 .108 14 .875 .9

9、375-20UNJEF .8903- .8933 1.354 1.54 1.311-1.314 1.030-1.032 .108 16 1.000 1.1250-18UNJEF 1.0714-1.0744 1.471 1.67 1.427-1.430 1.162-1.164 .108 20 1.250 1.3125-18UNJEF 1.2599-1.2629 1.795 1.98 1.750-1.753 1.387-1.389 .135 24 1.500 1.6250-18UNJEF 1.5724-1.5754 2.045 2.23 2.000-2.005 1.664-1.666 .135 3

10、2 2.000 2.1250-16UNJ 2.0627-2.0657 2.561 2.86 2.516-2.521 2.202-2.204 .135 TABLE 1B - DIMENSIONS F-M AND TOOLING BASIC NO. AS1300/12/SIZE CODE FGHJKMINLMREF TOOLING /4/ PORTING TOOL NO. BROACHING TOOL NO. CHIP REMOVAL TOOL 02 .153-.158 .296-.301 .507 24 .061 .418 .032 RPT02 RFOPB5002HDB RF02CR 03 .1

11、53-.158 .296-.301 .568 26 .061 .488 .032 RPT03 RFOPB5003HDB RF03CR 04 .153-.158 .296-.301 .568 30 .061 .534 .032 RPT04 RFOPB5004HDB RF04CR 05 .153-.158 .296-.301 .594 36 .061 .645 .032 RPT05 RFOPB5005HDB RF05CR 06 .168-.173 .311-.316 .631 36 .073 .720 .035 RPT06 RFOPB5006HDB RF06CR 08 .168-.173 .311

12、-.316 .672 40 .073 .831 .035 RPT08 RFOPB5008HDB RF08CR 10 .168-.173 .311-.316 .693 38 .073 1.062 .035 RPT10 RFOPB5010HDB RF10CR 12 .168-.173 .343-.348 .763 40 .073 1.192 .035 RPT12 RFOPB5012HDB RF12CR 14 .168-.173 .343-.348 .800 50 .073 1.364 .035 RPT14 RFOPB5014HDB RF14CR 16 .168-.173 .343-.348 .80

13、6 36 .073 1.481 .035 RPT16 RFOPB5016HDB RF16CR 20 .195-.200 .375-.380 .838 56 .093 1.805 .042 RPT20 RFOPB5020HDB RF20CR 24 .195-.200 .375-.380 .877 81 .093 2.055 .042 RPT24 RFOPB5024HDB RF24CR 32 .236-.241 .416-.421 1.050 102 .093 2.571 .042 RPT32 RFOPB5032HDB RF32CR NOTES: 1. THE DRILL AND PORTING

14、TOOL METHOD OF PREPARING THE MACHINED CAVITY IS MANDATORY FOR USE WITH RING-LOCKED FITTING INSTALLED IN ACCORDANCE WITH AS1301. DRILL .015-.030 SMALLER THAN MINOR DIA MODIFIED SPECIFIED. THE PORTING TOOL WILL SIZE THE MINOR DIA AND PROVIDE BALANCE OF CAVITY CONFIGURATION READY FOR BROACHING SERRATIO

15、N. /2/ AFTER SERRATIONS ARE BROACHED DIMENSION E APPLIES, CHIP AND DEFORMED MATERIAL REMOVAL IS REQUIRED. THE CHIP REMOVAL TOOL MAY NOT BE REQUIRED FOR TYPE B UNDERCUT PORT FITTING GEOMETRY. AEROSPACE STANDARD AS1300SHEET 3 OF 3REV. DPORT - RING LOCKED FLUID CONNECTION TYPE STANDARD DIMENSIONS FOR /

16、3/ FOR PORT DESIGNS THAT INCORPORATE A BOSS FEATURE, THE MINIMUM BOSS DIAMETER B AND BOSS LENGTH H ARE RECOMMENDED. THE MINIMUM BOSS FEATURES ARE TO SUPPORT THE AS1301 FITTING INSTALLATION TORQUE AND COUPLING NUT TORQUE. THE MINIMUM BOSS CONFIGURATION IS SATISFACTORY FOR USE IN MATERIALS THAT EXHIBI

17、T MINIMUM SHEAR STRENGTHS OF 26 KSI AND ELONGATION GREATER THAN 2%. STRESS ANALYSIS OR INTERFACE LOAD VERIFICATION TESTING OF THE PORT BOSS AT THE “LEAST MATERIAL CONDITION” (LMC) IS RECOMMENDED TO ENSURE THE PERFORMANCE OF THE FITTING ASSEMBLY IN EQUIPMENT OR COMPONENT DESIGN (REF. AS18280, AS5000,

18、 AS85720 AND QUALIFICATION TESTING). SPECIAL ATTENTION IS REQUIRED FOR SOME LOW DUCTILITY, LOW STRENGTH BOSS MATERIALS (SUCH AS ALUMINUM) AS BOSSES MAY DEVELOP UNACCEPTABLE EXTERNAL BOSS CRACKS DURING FITTING INSTALLATION. A GUIDELINE FOR BOSSES WITH SHEAR STRENGTH LESS THAN 26 KSI IS TO INCREASE TH

19、E MINIMUM BOSS DIAMETER B BY 15%. /4/ USE OF PORTING TOOL, BROACH TOOL, AND OPTIONAL CHIP REMOVAL TOOL SPECIFIED WILL GENERATE THE PORT CONFIGURATION. ALTERNATIVE TOOLS THAT CONFORM TO THE PORT DIMENSIONS AND THE PORT CONFIGURATION MAY BE USED. THE TOOLS SPECIFIED IN TABLE 1B ARE AVAILABLE FROM ALCO

20、A FASTENING SYSTEMS, FULLERTON, CA - CAGE CODE 66776; OR EQUIVALENT ALTERNATE SOURCES (FABER ENTERPRISES, CANOGA PARK, CA - CAGE CODE 14397; AND McKINNON INDUSTRIES, A SHUR-LOK COMPANY, IRVINE, CA - CAGE CODE 65085). 5. INTERPRETATION OF DRAWING PER AS4296. 6. A CHANGE BAR (l) LOCATED IN THE LEFT MA

21、RGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS

22、 AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra AND SEALING SURFACE TO BE 63 MICROINCHES Ra. 8. BREAK

23、 EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 9. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 10. KEY WORD: FITTING, FLUID CONNECTION, PORT. 11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 1. /12/ EXAMPLE OF DRAWING CALLOUT: a. TABULA

24、TED PART DRAWING: PORT RING-LOCKED DESIGN STANDARD PER AS1300 b. INDIVIDUAL PORT DRAWING: AS1300-02 B CHIP REMOVAL UNDERCUT SEE DETAIL Z BASIC PORT-RING LOCKED SIZE CODE TUBE SIZE IN INCHES DESIGN STANDARD NUMBER IF NO “TYPE” IS DESIGNATED ON THE EQUIPMENT OR COMPONENT SPECIFICATION OR DRAWING, THEN EITHER TYPE-A OR TYPE-B MAY BE SUPPLIED.