SAE AMS-DTL-22499 3A-2013 SHIM STOCK LAMINATED CRES《耐蚀钢层压衬垫》.pdf

《SAE AMS-DTL-22499 3A-2013 SHIM STOCK LAMINATED CRES《耐蚀钢层压衬垫》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS-DTL-22499 3A-2013 SHIM STOCK LAMINATED CRES《耐蚀钢层压衬垫》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDSHIM STOCK, LAMINATED, CRESAMS-DTL-22499/3Copyright 2009 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, wit

2、hout the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgIssued1998-09Revised 2013-03THIRD ANGLE PROJECTIONcustodian: REV.AFEDERAL

3、SUPPLY CLASS9515AMS-DTL-22499/3Sheet 1 of 3Rev.Aprocurement specification:SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability foranyparticularu

4、se,includingany patent infringementarisingtherefrom,isthesoleresponsibility oftheuser.”SAE reviews eachtechnical reportatleastevery fiveyears atwhichtimeitmay bereaffirmed,revised,orcancelled.SAE invitesyourwritten commentsandsuggestions.SAE VALUES YOUR INPUT. TO PROVIDE FEEDBACKON THIS TECHNICAL RE

5、PORT, PLEASE VISIT RATIONALEAMS-DTL-22499/3A results from a limited scope ballot to delete redundant part numbers (Table 1).NOTICETHIS DOCUMENT WAS ORIGINALLY TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-DTL-22499/3B, AND CONTAINED ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT

6、INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT WAS INTENDED TO REPLACE MIL-DTL-22499/3B. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD

7、 UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS

8、 VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUA

9、LIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT.AEROSPACE STANDARDAMS-DTL-22499/3SHEET 2 OF 3REV.ASHIM STOCK, LAMINATED, CRESTHE REQUIREMENT FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THISSPECIFICATION SHEET AND THE ISSUE OF THE FOLL

10、OWING SPECIFICATION SHEET AND THE ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DODISS) SPECIFIED IN THE SOLICITATION: MIL-DTL-22499.FIGURE 1 - BAR, METAL, FLATREQUIREMENTS1. MATERIAL: CORROSION RESISTANT STEEL (CRES) AS SPECIFIED IN PROCUREMENT DOCUMENT.2. TYPES:I - ALL

11、LAMINATIONSII - ONE-HALF SOLID STOCKCLASSES:1. - .002 INCH LAMINATIONS2. - .003 INCH LAMINATIONS3. PART NUMBERS: THE PART NUMBER CONSISTS OF M22499/3 THE BASIC NUMBER OF THIS SPECIFICATION SHEET AND A DASH NUMBER TAKEN FROM TABLE 1.AEROSPACE STANDARDAMS-DTL-22499/3SHEET 3 OF 3REV.ASHIM STOCK, LAMINA

12、TED, CRESTABLE 1Dash No. 1AThicknessBWidthLength,Feet Type Class001 0.016 20.000 4.000 I 1003 0.016 20.000 4.000 I 2005 0.020 20.000 4.000 I 1007 0.032 20.000 4.000 I 1009 0.054 20.000 4.000 I 1011 0.060 20.000 4.000 I 2013 0.062 3.750 0.312 I 1015 0.062 20.000 4.000 I 1017 0.062 24.000 4.000 II 102

13、1 0.074 12.000 3.000 I 1023 0.080 20.000 4.000 I 1025 0.093 24.000 4.000 I 2027 0.094 24.000 4.000 I 1029 0.120 20.000 4.000 I 1033 0.125 20.000 4.000 I 1037 0.126 20.000 4.000 I 2039 0.250 1.500 0.250 I 2041 0.250 24.000 4.000 II 1043 0.312 20.000 4.000 I 1045 0.376 20.000 4.000 I 2047 0.376 12.000 4.000 I 21. The dash numbers 031 and 035, contained in the previous revision of this specification were removed since they were redundant to dash numbers 029 and 033, respectively.