NSF 358-1-2014 Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems.pdf

《NSF 358-1-2014 Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems.pdf》由会员分享，可在线阅读，更多相关《NSF 358-1-2014 Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、NSF/ANSI 358-1 - 2014 Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems NSF International Standard/ American National Standard NSF International, an independent, not-for-profit, non-governmental organization, is dedicated to being the leading global provider

2、 of public health and safety-based risk management solutions while serving the interests of all stakeholders. This Standard is subject to revision. Contact NSF to confirm this revision is current. Users of this Standard may request clarifications and interpretations, or propose revisions by contacti

3、ng: Chair, Joint Committee on Plastics c/o NSF International 789 North Dixboro Road, P.O. Box 130140 Ann Arbor, Michigan 48113-0140 USA Phone: (734) 769-8010 Telex: 753215 NSF INTL FAX: (734) 769-0109 E-mail: infonsf.org Web: http:/www.nsf.org i NSF International Standard/ American National Standard

4、 for Plastics Polyethylene Pipe and Fittings for Water-Based Ground-Source “Geothermal” Heat Pump Systems Standard Developer NSF International NSF International Board of Directors Designated as an ANSI Standard February 3, 2014 American National Standards Institute NSF/ANSI 358-1 2014 ii Prepared by

5、 The NSF Joint Committee on Plastics Recommended for Adoption by The NSF Council of Public Health Consultants Adopted by NSF International July 2012 Revised August 2014 Published by NSF International PO Box 130140, Ann Arbor, Michigan 48113-0140, USA For ordering copies or for making inquiries with

6、regard to this Standard, please reference the designation “NSF/ANSI 358-1 - 2014.” Copyright 2014 NSF International Previous editions 2012 Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopyi

7、ng and microfilm, without permission in writing from NSF International. Printed in the United States of America. iii Disclaimers1NSF, in performing its functions in accordance with its objectives, does not assume or undertake to dis-charge any responsibility of the manufacturer or any other party. T

8、he opinions and findings of NSF repre-sent its professional judgment. NSF shall not be responsible to anyone for the use of or reliance upon this Standard by anyone. NSF shall not incur any obligation or liability for damages, including consequential damages, arising out of or in connection with the

9、 use, interpretation of, or reliance upon this Standard. NSF Standards provide basic criteria to promote sanitation and protection of the public health. Provisions for mechanical and electrical safety have not been included in this Standard because governmental agencies or other national standards-s

10、etting organizations provide safety requirements. Participation in NSF Standards development activities by regulatory agency representatives (federal, lo-cal, state) shall not constitute their agencys endorsement of NSF or any of its Standards. Preference is given to the use of performance criteria

11、measurable by examination or testing in NSF Standards development when such performance criteria may reasonably be used in lieu of design, mate-rials, or construction criteria. The illustrations, if provided, are intended to assist in understanding their adjacent standard requirements. However, the

12、illustrations may not include all requirements for a specific product or unit, nor do they show the only method of fabricating such arrangements. Such partial drawings shall not be used to justify im-proper or incomplete design and construction. Unless otherwise referenced, the annexes are not consi

13、dered an integral part of NSF Standards. The an-nexes are provided as general guidelines to the manufacturer, regulatory agency, user, or certifying or-ganization. 1The information contained in this Disclaimer is not part of this American National Standard (ANS) and has not been processed in accorda

14、nce with ANSIs requirements for an ANS. Therefore, this Disclaimer may contain material that has not been subjected to public review or a consensus process. In addition, it does not contain requirements neces-sary for conformance to the Standard. iv This page is intentionally left blank.v Contents 1

15、 General . 1 1.1 Purpose 1 1.2 Scope 1 2 Normative References . 1 3 Definitions . 2 4 Material Requirements 4 4.1 Plastic Materials 4 4.2 Materials . 4 4.3 Long-term strength of plastic pipe 4 4.4 Hydrostatic design 4 5 General Requirements 4 5.1 Polyethylene Pipe . 4 5.2 Polyethylene Fittings . 5 5

16、.3 Chemical Resistance 5 6 Marking Requirements 6 6.1 Pipe Marking 6 6.2 Fitting Marking 6 6.3 Manufacturers Instructions 6 7 Quality Assurance . 6 7.1 General . 6 7.2 Start-up and qualification of molds 7 7.3 Calibration 7 7.4 Quality assurance records 7 7.5 Production code identification . 7 7.6 N

17、umber of test specimens 8 vi This page is intentionally left blank.vii Foreword2 Geothermal technology has been used in North America for decades and is experiencing tremendous interest. In 2009, the NSF Joint Committee on Plastics and RV Plumbing Components proposed to develop this Standard after a

18、 need was identified in the industry. Plastic piping system components are used in the construction of earth energy systems yet there is no North American standard addressing all relevant aspects of earth energy systems. It is the intent of this Standard to assist in a more consistent approval and m

19、ainstream code adoption of the geothermal piping systems technology. This Standard will be separated into four separate documents based on material types. NSF/ANSI 358-1 addresses products in polyethylene systems. This edition of NSF/ANSI 358-1 includes the following revisions: Issue 2 This issue up

20、dated normative references in section 2, language in section 5.3, editorial correction in sections 6.1, 6.3.1 and 6.3.2, and updates to table 4. This Standard was developed by the NSF Joint Committee on Plastics using the consensus process described by the American National Standards Institute. Sugg

21、estions for improvement of this Standard are welcome. This Standard is maintained on a Continuous Maintenance schedule and can be opened for comment at any time. Comments should be sent to Chair, Joint Committee on Plastics at standardsnsf.org or, c/o NSF International, Standards Department, P.O. Bo

22、x 130140, Ann Arbor, Michigan, 48113-0140, USA. 2The information contained in this Foreword is not part of this American National Standard (ANS) and has not been processed in accordance with ANSIs requirements for an ANS. Therefore, this Foreword may contain material that has not been subjected to p

23、ublic review or a consensus process. In addition, it does not contain requirements neces-sary for conformance to the Standard. This page is intentionally left blank.1 2014 NSF NSF/ANSI 358-1 2014 NSF International Standard for Plastics Polyethylene Pipe and Fittings for Water-Based Ground-Source “Ge

24、othermal” Heat Pump Systems 1 General 1.1 Purpose This Standard establishes the minimum physical and performance requirements for plastic piping system components. These criteria were established for the protection of property, public health and the environment. 1.2 Scope The physical and performanc

25、e requirements in this Standard apply to plastic piping system components as well as non-plastic components of the ground loop heat exchanger including, but not limited to, pipes and fittings used in water-based ground-source heat pump systems. This Standard is intended for ground loop heat exchange

26、rs with a maximum temperature and pressure of 140 F (60 C) at 100 psi. Water-based ground-source heat pump systems commonly include the use of anti-freeze, heat transfer fluids or other chemical additives. This Standard does not cover refrigerant based ground loop heat exchangers such as direct expa

27、nsion (DX) systems. This Standard does not cover hydronic heating or cooling systems within buildings. 2 Normative references The following documents contain provisions that, through reference, constitute provisions of this NSF Standard. At the time this Standard was balloted, the editions listed be

28、low were valid. All documents are subject to revision, and parties are encouraged to investigate the possibility of applying the recent editions of the documents indicated below. The most recent published edition of the document shall be used for undated references. ASTM D2290-12. Standard Test Meth

29、od for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method3ASTM F1588-96(2011). Standard Test Method for Constant Tensile Load Joint Test (CTLJT)3ASTM D2683-10e1. Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyet

30、hylene Pipe and Tubing3 ASTM D2737-12a. Standard Specification for Polyethylene (PE) Plastic Tubing3 ASTM D2837-11. Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe 3American Society for Testing Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-29

31、59 . NSF 2014 NSF/ANSI 358-1 2014 2 Materials or Pressure Design Basis for Thermoplastic Pipe Products3ASTM D3035-12e1. Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter3 ASTM D3261-10a. Standard Specification for Butt Heat Fusion Polyethylene (PE

32、) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing3ASTM D3350-12e1. Standard Specification for Polyethylene Plastics Pipe and Fittings Materials3 ASTM D543-06. Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents3ASTM D638. Test Method for Tensile Propertie

33、s of Plastics3 ASTM F412-13. Terminology Relating to Plastic Piping Systems3 ASTM F714-13. Standard Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter3ASTM F1055-13. Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled P

34、olyethylene and Crosslinked Polyethylene Pipe and Tubing3ASTM F2620-12. Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings3AWWA C901-08. Polyethylene (PE) Pressure Pipe and Tubing, in (13 mm) Through 3 in (76 mm), for Water Service Plumbing Fittings4CSA B137.1-09. Polyethyle

35、ne Pipe, Tubing, and Fittings for Cold Water Pressure Services5National Institute of Standards and Technology (NIST)6PPI TR-3 (2010) Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Hydrostatic Design Stresses (HDS), Pressure Design Basis (PDB), Strength Design Basis (SDB), and

36、 Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe7PPI TR-4 (2011) PPI Listing of Hydrostatic Design Basis (HDB), Hydrostatic Design Stress (HDS), Strength Design Basis (SDB), Pressure Design Basis (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic P

37、iping Materials or Pipe73 Definitions Terms used in this Standard that have a specific technical meaning are defined here. 3.1 compound: A mixture of polymers with other ingredients such as fillers, stabilizers, catalysts, processing aids, lubricants, modifiers, pigments, or curing agents. NOTE Comp

38、ounds are considered materials; however, not all materials are considered compounds. 4American Water Works Association (AWWA), 6666 West Quincy Avenue, Denver, CO 80235 . 5Canadian Standards Association (CSA), 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3 . 6National Institute of Standards a

39、nd Technology (NIST), 100 Bureau Drive, Gaithersburg, MD 20899 7Plastics Pipe Institute, 105 Decker Court, Suite 825, Irving, Texas . NSF 2014 NSF/ANSI 358-1 2014 3 3.2 contamination: The presence of a substance not intentionally incorporated in a product. 3.3 critical dimensions: Dimensions of a pr

40、oduct (e.g., pipes and fittings) that directly affect the fit and function, or the capacity of making a sound joint, or both. 3.4 fitting: A piping component used to join, terminate, or provide changes of direction in a piping system. 3.5 ground-source heat pump system: A term used to describe a var

41、iety of mechanical systems that use the ground, groundwater, or surface water as a heat source or heat sink. Systems can be further described as ground-coupled, groundwater and surface water heat pump systems. 3.6 hydrostatic design basis (HDB): One of a series of established stress values specified

42、 in ASTM D2837 for a plastic compound, obtained by categorizing the long-term hydrostatic strength determined in accordance with ASTM D2837. 3.7 hydrostatic design stress (HDS): The estimated maximum tensile stress a material is capable of withstanding continuously with a high degree of certainty th

43、at failure of the pipe will not occur. This stress is circumferential when internal hydrostatic water pressure is applied. 3.8 joint: The location at which two pieces of pipe or a pipe and a fitting are connected together. Various joint types not defined in this Standard shall be defined by ASTM F41

44、2. 3.9 plastic pipe: A hollow cylinder of plastic, in which the wall thicknesses are usually small when compared to the diameter, and in which the inside and outside walls are essentially concentric. 3.10 plastic: A material that contains as an essential ingredient one or more organic polymeric subs

45、tances of large molecular weight, is solid in its finished state, and, at some stage in its manufacture or processing into finished articles, can be shaped by flow. 3.11 pressure rating: The estimated maximum water pressure at a specified temperature that a pipe is capable of withstanding continuous

46、ly with a high degree of certainty that failure of the pipe will not occur. 3.12 quality assurance: A formal system for verifying that products conform to specific standards. Quality assurance is intended as an audit of quality control testing. 3.13 quality control: The methods used to ensure that a

47、 production process yields products in conformance with the appropriate specifications established by the quality assurance program. 3.14 rework material: A material from a manufacturers own production that has been reground or pelletized for reuse by that same manufacturer. 3.15 steady-state: An op

48、erational condition of the manufacturing process that does not change with time. 3.16 thermoplastic: noun A plastic that can be repeatedly softened by heating and hardened by cooling through a temperature range characteristic of the plastic, and in the softened state, can be shaped by flow through m

49、olding or extrusion. adjective Capable of being repeatedly softened by heating and hardened by cooling through a temperature range characteristic of the plastic, and able in the softened state to be shaped by flow into articles by molding or extrusion. 3.17 virgin material: A material in the form of pellets, granules, powder, floc, or liquid that has not been subjected to use or processing other than that required for its initial manufacture. NSF 2014 NSF/ANSI 358-1 2014 4 4 Material requirements 4.1 Plastic materials Plastic piping system compone