BS 3619-1976 Specification - Mobile infusion stands《活动输注液支架规范》.pdf

《BS 3619-1976 Specification - Mobile infusion stands《活动输注液支架规范》.pdf》由会员分享，可在线阅读，更多相关《BS 3619-1976 Specification - Mobile infusion stands《活动输注液支架规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 3619:1976IncorporatingAmendment No.1SpecificationMobileinfusion standsUDC 615.473:615.38CONFIRMED DECEMBER 2007BS 3619:1976This British Standard, having been prepared under the directionof the Committee for Tubular Framed Equipment for Hospitals, was publishedunderthe authority o

2、f the Executive Board on30 April1976 BSI 08-1999First published May1963First revision April 1976The following BSI references relate to the work on this standard:Committee reference SGC/33Draft for comment73/61784 DCISBN 0 580 09002 7Co-operating organizationsThe Committee for Tubular Framed Equipmen

3、t for Hospitals, under whose supervision this British Standard was prepared, consists of representatives from the following Government departments and professional, scientific and industrial organizations:British Rubber Manufacturers AssociationBritish Surgical Trades Association (Inc.)Department of

4、 Health and Social SecurityDepartment of the EnvironmentInstitute of Purchasing and SupplyKing Edwards Hospital Fund for LondonNational Association of Hospital Supplies OfficersRoyal College of MidwivesRoyal College of Nursing and National Council of Nurses of the United KingdomRoyal College of Phys

5、icians of LondonTeaching Hospitals AssociationAmendments issued since publicationAmd. No. Date of issue Comments4321 August 1983 Indicated by a sideline in the marginBS 3619:1976 BSI 08-1999 iContentsPageCo-operating organizations Inside front coverForeword ii1Scope 12References 13Construction 14Mat

6、erials and dimensions 15Range of heights 16Pole for infusion containers 17Tubular column 18Base 29Castors 210 Stability 211 Finish 212 Marking 2Appendix A Stability test 3Figure 1 Apparatus for stability test 3Figure 2 Dimensions of hook bar and range of heights to theeffectivesuspension point 3Figu

7、re 3 Dimensions of hook bars for four containers 3Publications referred to Inside back coverBS 3619:1976ii BSI 08-1999ForewordThis British Standard is one of a series relating to tubular framed equipment for hospitals. It is a revision of BS 3619 “ Light mobile transfusion stands and transfusion pol

8、es for attachment to hospital beds”, and the principal changes concern dimensional and stability requirements.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.Compliance with a British

9、Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, pages i andii,pages 1 to 4, an inside back cover and a back cover.This standard has been updated (see copyright date) and may have had amendments incorpora

10、ted. This will be indicated in the amendment table on the inside front cover.BS 3619:1976 BSI 08-1999 11 ScopeThis British Standard specifies the basic requirements relating to materials, dimensions, construction and electrical safety precautions of mobile infusion stands for use in hospitals and in

11、fusion poles for attachment to hospital beds and other equipment.NOTE Attention is drawn to BS 4886-1 and BS 4886-2.2 ReferencesThe titles of the British Standards referred to in this standard are listed on the inside back cover.3 Construction3.1 General. Each mobile infusion stand (see Figure 1) sh

12、all comprise:a) a stainless steel pole with either two or four hooks for carrying the infusion containers as illustrated in Figure 2 or Figure 3;b) a tubular column (which may be of steel or stainless steel) to support the pole;c) a base.3.2 Welding3.2.1Welding shall comply with the requirements of

13、BS 5135 or BS 3019-2, as appropriate.3.2.2 Stainless steel tube shall be either inert-gas arc welded or resistance welded. For inert-gas arc welding the filler rod shall comply with type 347596specified in Table 1 of BS2901-2:1970.3.2.3 There shall be complete fusion of metal for all welded joints.

14、Sufficient welding metal shall be applied to allow for subsequent dressing smooth all over, without weakening the joint. There shall be no sharp edges and no crevices which may harbour dirt or foreign matter.4 Materials and dimensions4.1 The pole for carrying infusion containers shall be of bright d

15、rawn stainless steel rod, steel302S25or steel304S15, complying with the requirements of BS970-4:1970 (cold drawn conditions) of diameter12mm +1mm0mm.4.2 The hooks shall be of bright drawn stainless steel rod, steel302S25 or steel 304S15, complying with the requirements of BS970-4 (cold drawn conditi

16、ons) not less than 8mm in diameter, as shown in Figure 2.4.3 The tubular column which supports the pole shall be either steel or stainless steel having a minimum outside diameter of30mm and a minimum thickness of 1.6 mm.4.4 If steel tubing is used it shall comply with the requirements for any of the

17、 types and grades described in BS 1775 ERW and stainless steel shall comply with the requirements of BS3014:1958(grade1).4.5 The base for mobile infusion stands shall be of a material suitable for the service for which the equipment is intended and shall have a durability at least equal to that of t

18、he materials specified in 4.3 .The material used shall comply with the requirements of any relevant British Standards. If iron castings are used they shall comply with the requirements of BS 309 or of BS 310.5 Range of heightsThe range of heights, measured from the floor to the effective suspension

19、points of the hook bars shall be 1.75m minimum to2.75 m maximum.6 Pole for infusion containers6.1 Each stand shall be provided with a detachable pole as shown in Figure 2 for carrying two infusion containers, but at the option of the purchaser provision may be made for four containers, as shown in F

20、igure 3.6.2The overall length of the pole for mobile infusion stands will depend upon the design of base employed. Any pole shall however be long enough to ensure that, if the pole were accidentally released, the fingers could not be trapped between the hook bar and the top of the column. The lower1

21、00mm of the pole shall be permanently marked to illustrate the maximum height of adjustment.6.3 The top shall be in the form of a horizontally mounted bar or bars formed to a hook at each end and welded at the mid-point to the top of the pole. The effective suspension points of the hooks shall be as

22、 shown in Figure 2 and Figure 3.7 Tubular column7.1 The column shall be bossed at its upper end so as to maintain the pole vertical at all heights. The clearance between the pole and the boss shall not exceed 0.5 mm.7.2 Internally the column shall be provided at its lower end with a silencing device

23、 of a depth not less than50mm forming a cushion between the base of the column and the lower end of the infusion pole.BS 3619:19762 BSI 08-19997.3 The column shall be equipped with means of retaining the infusion pole at any desired height within its range and providing both easy adjustment and posi

24、tive locking. The grip shall be transmitted without scoring or otherwise damaging the surface of the pole. If a screw type locking device is used the thread shall be8mm 1.25 mm pitch, complying with the requirements of BS 3643.8 Base8.1 The dimension from the vertical centre line of the infusion pol

25、e to the centre line of the castor vertical pivot shall be between 205 mmand 255mm.8.2The overall width of the base, measured through its vertical centre line, shall not exceed 660mm.8.3The base shall maintain the column in a vertical position.8.4 Mobile infusion stands may be made suitable for dism

26、antling (knockdown) for ease of transport, but if the tubular column is detachable from the base, it shall be secure when located in position.NOTE The design of the base has not been specified but the purchaser might wish to consider the geometry of the base best suitedtohisrequirements.9 Castors9.1

27、 Each stand shall be fitted with castors complying with the requirements of BS 2099-1.They shall be not less than 50mm diameter.9.2 The castor tyres shall be of antistatic rubber composition, and when tested using the procedure given in A.4.11 of BS 2050:1978, both readings shall fall below 104 7 .1

28、0 StabilityThe design and weight of the stand shall be such that it remains stable when tested by the method described in Appendix A.NOTE It is essential that care be taken to ensure that if ancillary equipment is attached the stability of the stand is not impaired.11 Finish11.1 Completed stand. The

29、 completed stand shall be free from sharp edges and corners.11.2 Tubular column and base11.2.1 If of steel, the base and the tubular column shall be finished with a good quality stoving enamel or an epoxide based enamel or powder.Prior to applying the finish, all rust, grease, scale or surface adhes

30、ions of a like nature shall be removed and all welds shall be properly dressed and cleaned up and the surface given a coat of inhibitive primer.11.2.2 The finishing coat shall be stoved strictly in accordance with the paint manufacturers stoving schedule and shall provide a dry film thickness of not

31、 less than 0.025mm. The finish shall be smooth, free from dust, runs and any other such defects.NOTE It is important that the stand should be stoved before castors are fitted. Holes to receive screws should be reamed orre-tapped after stoving to remove any enamel or other insulating material from th

32、e hole. The importance of this procedure is stressed since the conductive qualities of the castors could be destroyed by an insulating coating.11.3 Performance tests. The finish shall comply with the requirements of 11.3.1 to 11.3.4.11.3.1 Resistance to bend effects. The finish on the test panel sha

33、ll withstand bending over a12 mmdiameter mandrel without cracking or loss of adhesion when tested in accordance withBS 3900-E1 using a steel panel and the type 2apparatus.11.3.2 Scratch resistance. The finish on the test panel shall not be penetrated when tested in accordance with BS 3900-E2 using a

34、 needle load of 3000 g.11.3.3 Impact resistance. The finish on the test panel shall not rupture when tested in accordance with BS 3900-E3 at an indentation depth of3mm.11.3.4 Resistance to cupping effect. The finish of the test panel shall not crack or become detached from the metal substrate when t

35、ested in accordance with BS 3900-E4 at an indentation depth of 3mm.11.4 Stainless steel finish. Stainless steel finish shall be polished to match finish No 8 ofBS 1449-2:1975.12 MarkingMobile infusion stands complying with the requirements of this British Standard shall be clearly and indelibly mark

36、ed with the following.a) The name, trade mark or other means of identification of the manufacturer.b) The year of manufacture.c) The number of this British Standard, i.e.BS 3619.BS 3619:1976 BSI 08-1999 3Appendix A Stability test (See clause 10)The infusion pole shall be adjusted to a height of2.7 m

37、 and so arranged that a hook bar is approximately at right angles to the stop strip as illustrated in Figure 1.A1000ml MRC bottle filled with water shall be suspended from the hook.The stand shall be placed with two adjacent castor wheels resting against a positive stop on a flat base at an angle of

38、 9 to the horizontal. Figure 1Apparatus for stability testFigure 2 Dimensions of hook bar and range of heights to the effective suspension pointFigure 3 Dimensions of hook bars for four containers4 blank BS 3619:1976 BSI 08-1999Publications referred toThis standard makes reference to the following B

39、ritish Standards:BS 309,Whiteheart malleable iron castings.BS 310, Blackheart malleable iron castings.BS 970,Wrought steels in the form of blooms, billets, bar and forgings.BS 970-4, Stainless, heat resisting and valve steels.BS 1449,Steel plate, sheet and strip.BS 1449-2,Stainless and heat resistin

40、g steel plate, sheet and strip.BS 1453,Filler materials for gas welding.BS 1775,Steel tubes for mechanical, structural and general engineering purposes.BS 2050,Electrical resistance of conductive and anti-static products made from flexible polymeric material.BS 2099,Castors.BS 2099-1,Castors for hos

41、pital equipment for ward and theatre use.BS 2901,Filler rods and wires for gas-shielded arc welding.BS 2901-2,Austenitic stainless steels.BS 3014,“As welded” and cold drawn welded austenitic stainless steel tubes for mechanical, structural and general engineering purposes.BS 3019,General recommendat

42、ions for manual inert-gas tungsten-arc welding.BS 3019-2,Austenitic stainless and heat-resisting steels.BS 3643,ISO metric screw threads.BS 3900,Methods of test for paints.BS 3900-E1,Bend test (cylindrical mandrel).BS 3900-E2,Scratch test.BS 3900-E3,Impact (falling weight) resistance.BS 3900-E4, Cup

43、ping test.BS 4886,Hospital bedsteads.BS 4886-1,Bedsteads of variable height.BS 4886-2,Bedsteads of fixed height.BS 5135,Metal-arc welding of carbon and carbon manganese steels.BS 3619:1976BSI389 Chiswick High RoadLondonW4 4ALBSIBritish StandardsInstitutionBSI is the independent national body respons

44、ible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritishStandards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments

45、or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on

46、the inside front cover. Tel:020 89969000. Fax:020 89967400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should b

47、e addressed to Customer Services. Tel:0208996 9001. Fax:0208996 7001.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide rang

48、e of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:020 89967111. Fa

49、x:020 89967048.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:020 89967002. Fax:020 89967001.CopyrightCopyrightsubsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act