NEMA NTCIP 1207-2014 National Transportation Communications for ITS Protocol - Object Definitions for Ramp Meter Control (RMC) Units (V02 14).pdf

《NEMA NTCIP 1207-2014 National Transportation Communications for ITS Protocol - Object Definitions for Ramp Meter Control (RMC) Units (V02 14).pdf》由会员分享，可在线阅读，更多相关《NEMA NTCIP 1207-2014 National Transportation Communications for ITS Protocol - Object Definitions for Ramp Meter Control (RMC) Units (V02 14).pdf（242页珍藏版）》请在麦多课文档分享上搜索。

1、A Joint Publication of:American Association of State Highway and Transportation Officials (AASHTO) Institute of Transportation Engineers (ITE)National Electrical Manufacturers Association (NEMA)NTCIP Standards PublicationNTCIP 1207:2014 v02.14National TransportationCommunications for ITS ProtocolObj

2、ect Definitions forRamp Meter Control (RMC) UnitsA Joint Standard of AASHTO, ITE, and NEMAA Joint Standard of AASHTO, ITE, and NEMA NTCIP 1207 version v02 National Transportation Communications for ITS Protocol Object Definitions for Ramp Meter Control (RMC) Units Published September 2014 Published

3、by American Association of State Highway and Transportation Officials (AASHTO) 444 North Capitol Street, N.W., Suite 249 Washington, D.C. 20001 Institute of Transportation Engineers (ITE) 1627 I (“Eye”) Street, N.W., Suite 600 Washington, D.C. 20006 National Electrical Manufacturers Association (NEM

4、A) 1300 North 17th Street, Suite 900 Rosslyn, Virginia 22209-3801 file version 1207 v02.14p 2014 AASHTO / ITE / NEMA. All rights reserved. . NOTICES Copyright Notice 2014 by the American Association of State Highway and Transportation Officials (AASHTO), the Institute of Transportation Engineers (IT

5、E), and the National Electrical Manufacturers Association (NEMA). All intellectual property rights, including, but not limited to, the rights of reproduction, translation and display are reserved under the laws of the United States of America, the Universal Copyright Convention, the Berne Convention

6、, and the International and Pan American Copyright Conventions. Except as licensed or permitted, you may not copy these materials without prior written permission from AASHTO, ITE, or NEMA. Use of these materials does not give you any rights of ownership or claim of copyright in or to these material

7、s. Visit www.ntcip.org for other copyright information, for instructions to request reprints of excerpts, and to request reproduction that is not granted below. PDF File License Agreement To the extent that these materials are distributed by AASHTO / ITE / NEMA in the form of an Adobe Portable Docum

8、ent Format (PDF) electronic data file (the “PDF file”), AASHTO / ITE / NEMA authorizes each registered PDF file user to view, download, copy, or print the PDF file available from the authorized website, subject to the terms and conditions of this license agreement: a) you may download one copy of ea

9、ch PDF file for personal, noncommercial, and intraorganizational use only; b) ownership of the PDF file is not transferred to you; you are licensed to use the PDF file; c) you may make one more electronic copy of the PDF file, such as to a second hard drive or burn to a CD; d) you agree not to copy,

10、 distribute, or transfer the PDF file from that media to any other electronic media or device; e) you may print one paper copy of the PDF file; f) you may make one paper reproduction of the printed copy; g) any permitted copies of the PDF file must retain the copyright notice, and any other propriet

11、ary notices contained in the file; h) the PDF file license does not include (1) resale of the PDF file or copies, (2) republishing the content in compendiums or anthologies, (3) publishing excerpts in commercial publications or works for hire, (4) editing or modification of the PDF file except those

12、 portions as permitted, (5) posting on network servers or distribution by electronic mail or from electronic storage devices, and (6) translation to other languages or conversion to other electronic formats; i) other use of the PDF file and printed copy requires express, prior written consent. Data

13、Dictionary and MIB Distribution Permission To the extent that these materials are distributed by AASHTO / ITE / NEMA in the form of a Data Dictionary (“DD”) or Management Information Base (“MIB”), AASHTO / ITE / NEMA extend the following permission: You may make or distribute unlimited copies, inclu

14、ding derivative works, of the DD or MIB, including copies for commercial distribution, provided that: a) each copy you make or distribute includes the citation “Derived from NTCIP 0000 insert the standard number. Copyright by AASHTO / ITE / NEMA. Used by permission.”; b) the copies or derivative wor

15、ks are not made part of the standard publications or works offered by other standard developing organizations or publishers or as works-for-hire not associated with commercial hardware or software products intended for field implementation; c) use of the DD or MIB is restricted in that the syntax fi

16、elds may only be modified to define: 1) a more restrictive subrange; or 2) a subset of the standard enumerated values; or 3) a set of retired and defined enumerated values for systems supporting multiversion interoperability; d) the description field may be modified but only to the extent that: 1) t

17、he more restrictive subrange is defined; and 2) only those bit values or enumerated values that are supported are listed. These materials are delivered “AS IS” without any warranties as to their use or performance. AASHTO / ITE / NEMA and their suppliers do not warrant the performance or results you

18、 may obtain by using these materials. AASHTO / ITE / NEMA and their suppliers make no warranties, express or implied, as to noninfringement of third party rights, merchantability, or fitness for any particular purpose. In no event will AASHTO / ITE / NEMA or their suppliers be liable to you or any t

19、hird party for any claim or for any consequential, incidental or special damages, including any lost profits or lost savings, arising from your reproduction or use of these materials, even if an AASHTO / ITE / NEMA representative has been advised of the possibility of such damages. Some states or ju

20、risdictions do not allow the exclusion or limitation of incidental, consequential, or special damages, or the exclusion of implied warranties, so the above limitations may not apply to a given user. Use of these materials does not constitute an endorsement or affiliation by or between AASHTO, ITE, o

21、r NEMA and the user, the users company, or the products and services of the users company. If the user is unwilling to accept the foregoing restrictions, he or she should immediately return these materials. PRL and RTM Distribution Permission To the extent that these materials are distributed by AAS

22、HTO / ITE / NEMA in the form of a Profile Requirements List (“PRL”) or a Requirements Traceability Matrix (“RTM”), AASHTO / ITE / NEMA extend the following permission: a) you may make or distribute unlimited copies, including derivative works of the PRL (then known as a Profile Implementation Confor

23、mance Statement (“PICS”) or the RTM, provided that each copy you make or distribute contains the citation “Based on NTCIP 0000 insert the standard number PRL or RTM. Used by permission. Original text AASHTO / ITE / NEMA.” b) you may only modify the PRL or the RTM by adding: 1) text in the Project Re

24、quirements column, which is the only column that may be modified to show a products implementation or the project-specific requirements; and/or 2) additional table columns or table rows that are clearly labeled as ADDITIONAL for project-unique or vendor-unique features; and c) if the PRL or RTM exce

25、rpt is made from an unapproved draft, add to the citation “PRL (or RTM) excerpted from a draft standard containing preliminary information that is subject to change.” This limited permission does not include reuse in works offered by other standards developing organizations or publishers, and does n

26、ot include reuse in works-for-hire, compendiums, or electronic storage devices that are not associated with procurement documents, or commercial hardware, or commercial software products intended for field installation. A PICS is a Profile Requirements List that is completed to indicate the features

27、 that are supported in an implementation. Visit www.ntcip.org for information on electronic copies of the MIBs, PRLs, and RTMs. Content and Liability Disclaimer The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of

28、 the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. AASHTO, ITE, and NEMA standards and guideline publications, of which the document contained herein is one, are devel

29、oped through a voluntary consensus standards development process. This process brings together volunteers and seeks out the views of persons who have an interest in the topic covered by this publication. While AASHTO, ITE, and NEMA administer the process and establish rules to promote fairness in th

30、e development of consensus, they do not write the document and they do not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in their standards and guideline publications. AASHTO, ITE, and NEMA disclaim liability for a

31、ny personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. AASHTO, ITE, and NEMA disclaim and make no guaranty or warrant

32、y, express or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. AASHTO, ITE, and NEMA do not undertake to guarantee the performance of any i

33、ndividual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, AASHTO, ITE, and NEMA are not undertaking to render professional or other services for or on behalf of any person or entity, nor are AASHTO, ITE, and NEMA und

34、ertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Informat

35、ion and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. AASHTO, ITE, and NEMA have no power, nor do they undertake to police or enforce compliance wit

36、h the contents of this document. AASHTO, ITE, and NEMA do not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safety-related information in this document shall not be attributable to AA

37、SHTO, ITE, or NEMA and is solely the responsibility of the certifier or maker of the statement. Trademark Notice NTCIP is a trademark of AASHTO / ITE / NEMA. All other marks mentioned in this standard are the trademarks of their respective owners. NTCIP 1207 v02.14 Page i ACKNOWLEDGEMENTS NTCIP 1207

38、 v02 was prepared by the NTCIP Ramp Meter Control Working Group, which is a subdivision of the Joint Committee on the NTCIP. The Joint Committee is organized under a Memorandum of Understanding among AASHTO, ITE, and (NEMA). The Joint Committee on the NTCIP consists of six representatives from each

39、of the standards organizations, and provides guidance for NTCIP development. At the time that NTCIP 1207 v02 was prepared, the following individuals were active members of the NTCIP RMC Working Group: Brian Simi (Chair) Sean Coughlin Terry Haukom W.L. Bud Kent Mark Fox Joerg Nu Rosenbohm Edmund Chan

40、g Glenn Massarano Jeff McRae Mark Morse Other individuals providing input to NTCIP 1207 v02 include: Blake Christie David Cordone John Haigwood Curtis Herrick Pete Marshall Tom Timcho Jeris White In addition to the many volunteer efforts, recognition is also given to those organizations which suppor

41、ted the efforts of the working group by providing comments and funding for NTCIP 1207 v02, including: Batelle California Department of Transportation (Caltrans) Minnesota Department of Transportation (MnDOT) Noblis Inc. (formerly known as Mitretek Inc.) Siemens (formerly known as Eagle Traffic Contr

42、ol Systems and Gardner Systems) Ministry of Transportation of Ontario (MTO) Telvent Farradyne Inc. (formerly known as PB Farradyne) Texas Transportation Institute (TTI) TransCore Inc. Washington State Department of Transportation (WSDOT) In addition to the many volunteer efforts, the U.S. Department

43、 of Transportation, Federal Highway Administration and Joint Program Office, provided funding assistance for the development of the NTCIP standards and associated documents. 2014 AASHTO / ITE / NEMA Do Not Copy Without Written Permission NTCIP 1207 v02.14 Page ii FOREWORD NTCIP 1207 v02 identifies a

44、nd defines how a management station may wish to interface with a field device to control and monitor RMC units. NTCIP 1207 v02 provides definitions of data elements for use within ramp meter control. The data is defined using the Simple Network Management Protocol (SNMP) object-type format as define

45、d in RFC 1212. NTCIP 1207 v02 defines requirements that are applicable to all NTCIP RMC units and also contains optional and conditional sections that are applicable to specific environments for which they are intended. NTCIP 1207 v02 contains two normative and three informative annexes: a) Annex A

46、is informative and contains the Operations Concept and basically the functional requirements of a RMC unit. b) Annex B is normative and contains the Profile Requirements List (PRL), which has also been referred to as a Profile Implementation Conformance Statement (PICS). The PRL table includes each

47、of the defined object definitions, their potential value ranges, an indication whether the object is a control, status, or database parameter, and a column allowing a user to enter project-specific information. Since 2007 when NTCIP 1207 v02 last underwent major revision, the organization and format

48、ting of the systems engineering content in 1200-series standards has evolved. The NTCIP 1207 v03 will present systems engineering content in the more complete and correct format. c) Annex C is informative and contains the object tree showing the major nodes of the RMC unit object structure within th

49、e Global object tree. d) Annex D does not currently contain any data. In future, this annex is intended to contain the test procedures for testing a device for conformance to NTCIP 1207 v02, which is designated as a Normative annex. e) Annex E is informative and contains all the changes that have been made between the prior version of NTCIP 1207 and NTCIP 1207 v02. NTCIP 1207 v02 is an NTCIP Data Dictionary Standard. Data Dictionary Standards provide definitions of data elements for use within NTCIP systems. NTCIP 1