NAVY MIL-STD-1647 E-2003 IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS BALL ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS《环形仪器及精密零件钢球国内生产的轴承识别标记》.pdf

《NAVY MIL-STD-1647 E-2003 IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS BALL ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS《环形仪器及精密零件钢球国内生产的轴承识别标记》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-STD-1647 E-2003 IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS BALL ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS《环形仪器及精密零件钢球国内生产的轴承识别标记》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-STD-1647E 21 April 2003 SUPERSEDING MIL-STD-1647D 04 October 1993 DEPARTMENT OF DEFENSE STANDARD PRACTICE IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS, BALL, ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS AMSC N/A FSC 3110 DISTRIBUTION STATEMENT A. Approved for public releas

2、e; distribution is unlimited. NOT MEASUREMENT SENSITIVE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1647E ii FOREWORD 1. This standard is approved for use by all Departments and Agencies of the Department of Defense. 2. This document esta

3、blishes the symbolic markings to be used for the identification of bearings manufactured in the United States and Canada for use in defense contracts. The markings chosen comply with those established and accepted as standard by the bearing industry. 3. Beneficial comments (recommendations, addition

4、s, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Air Warfare Center Aircraft Division, Code 414100B120-3, Hwy 547, Lakehurst, NJ 08733-5100, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing

5、 at the end of this document or by letter. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1647E iii CONTENTS PAGE PARAGRAPH FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii 1. SCOPE . . . . . . . . . . . . . . . . . . .

6、. . . . . . . . . . . . . 1 1.1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. APPLICABLE DOCUMENTS . . . . . . . . . . . . . . . . . . . . 1 2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.2 Government documents . . . . . . . . . . . . . . . .

7、 . . . . . . 1 2.2.1 Specifications and standards . . . . . . . . . . . . . . . . . . . . 1 2.3 Non-Government publications . . . . . . . . . . . . . . . . . . . 2 2.4 Order of precedence. . . . . . . . . . . . . . . . . . . . . . . . 3 3. DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . .

8、. . . . . 3 3.1 Miniature and instrument type annular ball bearings. . . . . . . . 3 3.2 Domestic manufacture . . . . . . . . . . . . . . . . . . . . . . 3 3.3 Made in U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.4 Basic bearing part number. . . . . . . . . . . . . . . . . . . . .

9、3 3.5 Chrome steel 52100. . . . . . . . . . . . . . . . . . . . . . . . . 3 3.6 Stainless (corrosion-resistant) steel 440C. . . . . . . . . . . . . . 3 4 GENERAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . 3 4.1 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 DETA

10、ILED REQUIREMENTS . . . . . . . . . . . . . . . . . . . . 3 5.1 Literal (non-symbolic) identification . . . . . . . . . . . . . . . . 4 5.2 Symbolic marking. . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.3 Indirect marking . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.4 Barrier coa

11、ted bearing marking . . . . . . . . . . . . . . . . . . . 4 5.5 Duplex bearing marking . . . . . . . . . . . . . . . . . . . . . . 4 5.6 Source and specification control bearing marking . . . . . . . . . 4 5.7 Exemptions from marking requirements . . . . . . . . . . . . . . 4 5.8 Certification of sy

12、mbolic markings. . . . . . . . . . . . . . . . . 4 5.9 Marking methods . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6. NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6.2 Issue of DoDISS . .

13、 . . . . . . . . . . . . . . . . . . . . . . . . 6 6.3 Subject term (keyword) listing . . . . . . . . . . . . . . . . . . . 6 6.4 Changes from previous issue. . . . . . . . . . . . . . . . . . . . 6 FIGURE 1 Symbolic markings. . . . . . . . . . . . . . . . . . . . . . . . . 5 CONCLUDING MATERIAL. .

14、. . . . . . . . . . . . . . . . . . . . 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1647E 1 1. SCOPE 1.1 Scope. This standard establishes the marking requirements for identification and certification of miniature and instrument type ann

15、ular ball bearings of domestic manufacture. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this standard. This section does not include documents cited in other sections of this standard or recommended for additional information or

16、as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3, 4, and 5 of this standard, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications

17、and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement th

18、ereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL FF-B-171 Bearings, Ball, Annular (General Purpose), Metric FF-B-2844 Bearings, Ball, Annular (General Purpose) DEPARTMENT OF DEFENSE MIL-B-913 Bearings, Ball, Annular, for Instruments and Precision Rotating Components (Metric), Gener

19、al Specification For MIL-B-81793 Bearings, Ball, Annular, for Instruments and Precision Rotating Components Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1647E 2 STANDARDS DEPARTMENT OF DEFENSE MIL-STD-129 Military Marking for Shipment and

20、Storage MIL-STD-130 Identification Marking of U.S. Military Property (Unless otherwise indicated, copies of the above specifications and standards are available from the Standardization Document Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 19111-5094 or www.dodssp.daps.mil.) 2.3 Non-Go

21、vernment publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of t

22、he documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-A295 Steel, Bearing, High-Carbon Anti-friction. (DoD adopted) (Application for copies should be addressed to ASTM International, P.O. Box

23、C700, West Conshocken, PA 19428-2959 or www.astm.org.). SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE-AS13341 Process for Barrier Coating of Anti-Friction Bearings. (DoD adopted) SAE-AMS5618 Steel, Corrosion-Resistant, Bars, Wire, and Forgings, 17CR-0.52MO (0.95 1.20C) (SAE 51440C), Consumable Electrode

24、 Vacuum Melted. (DoD adopted) SAE-AMS5630 Steel, Corrosion Resistant, Bars, Wire, and Forgings, 17CR-0.52 MO (0.95 1.20C) (SAE 51440C). (DoD adopted) SAE-AMS5880 Steel, Corrosion Resistant, Bars, Forgings, and Wire 17CR-0.52 MO (0.95 1.20C) (SAE 51440C) for Bearing Applications. (DoD adopted) SAE-AM

25、S6440 Steel, Bars, Forgings, and Tubing 1.45CR (0.98 1.10C) (SAE 52100) for Bearing Applications. (DoD adopted) SAE-AMS6444 Steel Bars, Forgings and Tubing 1.45CR (0.98 1.10C) (SAE 52100) Premium Aircraft-Quality, Consumable Electrode Vacuum Melted. (DoD adopted) Provided by IHSNot for ResaleNo repr

26、oduction or networking permitted without license from IHS-,-,-MIL-STD-1647E 3 SAE-AMS6447 Steel Bars, Forgings, and Tubing 1.4CR (0.98 1.10C) (SAE 52100) Electroslag Remelted. (DoD adopted) (Application for copies should be addressed to the Society of Automotive Engineers (SAE), 400 Commonwealth Dri

27、ve, Warrendale, PA 15096-0001 or http:/www.sae.org) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless

28、a specific exemption has been obtained. 3. DEFINITIONS 3.1 Miniature and instrument type annular ball bearings. For purposes of this document, any reference to “bearings” or “ball bearings” will mean miniature and instrument type annular ball bearings, ABEC 1 tolerance or better and 30mm outer diame

29、ter (OD) (1.1811 inch) and smaller. 3.2 Domestic manufacture. Domestically manufactured ball bearings are those which are assembled in the United States or Canada. When a ball bearing is involved, all components of the assembly must also have been manufactured in the United States or Canada. 3.3 Mad

30、e in USA Made in USA refers to ball bearings and components of ball bearings completely manufactured, assembled and tested within the United States of America. 3.4 Basic bearing part number. The basic bearing part number refers to the group of numbers or letters in a manufacturers part number which

31、specifies the bore, outside diameter, width, material and the number of shields or seals used. 3.5 Chrome steel 52100. Chrome steel is defined under the following specifications: ASTM-A295, SAE-AMS6440, 6444, 6447. 3.6 Stainless steel 440C. Stainless steel is defined under the following specificatio

32、ns: SAE-AMS5618, 5630, 5880. 4. GENERAL REQUIREMENTS 4.1 Identification. All bearings used in any DoD contract, or bearings supplied for the repair of a DoD contract item shall be marked in accordance with one of the methods in Detailed Requirements. Provided by IHSNot for ResaleNo reproduction or n

33、etworking permitted without license from IHS-,-,-MIL-STD-1647E 4 5. DETAILED REQUIREMENTS 5.1 Literal (non-symbolic) identification. Bearings (miniature, instrument and instrument precision) having an adequate width on either the inner or the outer ring face shall be marked in accordance with MIL-ST

34、D-130. In addition, the bearing shall be marked “Made in USA” or “USA”, or “Made in Canada” or “Canada”. The use of symbolic marking may be used in addition to MIL-STD-130 marking. 5.2 Symbolic marking. Symbolic marking shall be used when the bearing is too small to place the literal markings requir

35、ed by MIL-STD-130 on the ring faces. The applicable symbolic marking illustrated on figure 1 shall be marked on the inner or outer ring face of bearings, ABEC 1 or better 30mm/1.1811 inch OD or less. Symbolic markings shall fully identify the manufacturer of the bearing and the material used in its

36、manufacture (440C stainless steel or 52100 chrome steel). 5.3 Indirect marking. Bearings having an inadequate face width for the symbolic markings (see figure 1) shall be exempt from the marking requirements of 5.2. The unit packages of such bearings shall be marked in accordance with MIL-STD-129. 5

37、.4 Barrier coated bearing marking. In addition to the requirements of 5.1 and 5.2, barrier coated bearings shall be marked in accordance with SAE-AS13341. Such markings shall be accomplished prior to barrier coating of the bearing. 5.5 Duplex bearing marking. Duplex bearings shall be marked in accor

38、dance with the requirements of 5.1 to 5.3 and MIL-B-913, MIL-B-81793, FF-B-171 and FF-B-2844. In addition, bearings furnished as duplex pairs shall be marked to identify their relative position to each other in the assembly. Instructions shall be included with duplex bearings to identify such markin

39、gs. 5.6 Source and specification control bearing marking. These bearings shall be marked in accordance with the requirements specified in 5.1 through 5.5. The packaging of these bearings shall be in accordance with MIL-STD-129. 5.7 Exemptions from marking requirements. Bearings made of materials oth

40、er than 440C and 52100 steels, bearings of configuration other than conventional radial or angular contact type, and bearings where marking is specifically prohibited by the Government shall be exempt from all marking requirements of this standard. Such bearings shall be marked as specified in the a

41、pplicable contract. 5.8 Certification of symbolic markings. All bearing manufacturers using symbolic markings shall furnish a notarized certification that the symbolic markings shall have the same meaning as the words “Made in USA”, “USA”, or “Made in Canada”,“Canada”. The certification shall indica

42、te the bearing was manufactured of stainless (corrosion resistant) steel (440C) or chrome steel (52100) to tolerances which are equal to or exceed the requirements for Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1647E 5 ABEC 1 to ABEC 3 A

43、BEC 5 or better COMPANY NAME Chrome Steel 52100 Stainless Steel 440C Chrome Steel 52100 Stainless Steel 440C NEW HAMPSHIRE BALL BEARING INC. (PETERBOROUGH, NH) NEW HAMPSHIRE BALL BEARING INC (CHATSWORTH, CA) PACAMOR/KUBAR BEARING INC. SUPER PRECISION BEARING DIV, TIMKEN CORP. BARDEN CORP. * * * BARD

44、EN HAS NO SYMBOLS FOR ABEC 1 AND ABEC 3 FIGURE 1. Symbolic markings. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1647E 6 ABEC 1. The certificate shall be sent to: Commander, Naval Air Systems Command, Code 4.3.5.4, 48110 Shaw Road, Bldg.

45、2187, Patuxent River, MD 20670-5304. 5.9 Marking methods. Markings shall not result in raised metal or in any way affect the function of the bearing. The marking shall be applied by stamping, laser, electroetch, or any other permanent method. Selection of the permanent marking method is left to the

46、manufacturer. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. This document shows the markings to be used by domestic (U.S. and Canada) manufacturers to identify their bearings used in military contracts. Th

47、is document also tells how to apply the markings to the bearing surfaces. 6.2 Issue of DoDISS. When this standard is used in acquisition, the applicable issue of the DoDISS must be cited in the solicitation (see 2.2.1 and 2.3). 6.3 Subject term (keyword) listing. Barrier coated Duplex Literal Miniat

48、ure Symbolic 6.4 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity: Army AT Navy AS Navy AS (Project No. 3110-1303) Air Force 99 Review Activities: Air Force 84 DLA GS, LSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,