NAVY MIL-G-19465 E-1980 GLOVE MAN-S (LEATHER CHIPPER)《男式手套(皮革切削)》.pdf

《NAVY MIL-G-19465 E-1980 GLOVE MAN-S (LEATHER CHIPPER)《男式手套(皮革切削)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-G-19465 E-1980 GLOVE MAN-S (LEATHER CHIPPER)《男式手套(皮革切削)》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、31 January 19 74 MILITARY SPECIFICATION . GLOVE , CHIPPER s , GAUNTLET This specification is approved for use by Navy Clothing and Textile Research Facility, Department of the Navy and is available for use by all Departments and Agencies of the Department of Defense. 1 1. SCOPE 1.1 Scope. This speci

2、fication covers the requirements for one type of leather work glove. 1.2 Classification. The glove shall be procured by the following sizes for either the left or right hand as specified (see 6.2): Small Medium Large Extra-Large 2. APPLICABLE DOCUMENTS 2.1 Issue of documents: The following documents

3、 of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL V-T-276 - Thread, Cotton KK-L-2004 - Leather, Cattlehide, Deerskin and Horsehide, ccc-c-419 - Cloth, Duck, Cotton, Unbleached, Plie

4、d - Yarns DDD-L- 20 - Label; for Clothing, Equipage, and Tentage Chrome Tanned Army and Numbered (General Use) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to Officer in Charge, Navy Clothing and

5、 Textile Research Facility, 21 Strathmore Road, Natick, MA 01760, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document . FSC 8415 THIS DOCUMENT CNTMN PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted w

6、ithout license from IHS-,-,-MIL-G-Lq4b5E 4 W 7779906 0383423 W MIL-G-l9465E(NU) MILITARY MIL-B-17757 STANDARDS FEDERAL FED-STD-191 FED-STD-311 FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 - Boxes, Shipping Fiberboard, (Modular Sizes) - Textile Test Methods - Leather, Methods of Sampling and Testing

7、- Stitches, Seams, and Stitchings - Samplng Procedures and Tables for Inspection - Marking for Shipment and Storage by Attributes (Copies of specifications, standards, drawings, and publications required by contractor in connection with specific procurement functions should be obtained from the proc

8、uring activity or as directed by the contracting officer.) LAWS AND REGULATIONS U:S. Postal Service Manual (Copies of the manual may be obtained from the Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20406) 2.2 Other publications. The following documents form a part o

9、f this specification to the extent specified herein. Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply: NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies sh

10、ould be addressed to American Trucking Associa- tion, Traffic Department, 1616 P Street, N.W., Washington, DC 20036.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South River

11、side Plaza, Chicago, IL 60606.) * m Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-14465E 84 m 7777706 0383424 T MIL-G-l9465E(NU) U.S. DEPARTMENT OF AGRICULTURE Methods of Test for Grade of Wool (Application for copies should be addressed to t

12、he U.S. Department of Agriculture, Agricultural Marketing Service, Washington, D.C. 20402.) 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample, in which case this

13、specification shall govern. * 3.2 First article. When specified (see 6.2), the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3). 3.3 Materials. 3.3.1 Leather. The leather used in the fabrication of the glove, shall conform to the requirements specified in 3

14、.3.1.1 and 3.3.1.2. * 3.3.1.1 Hand section. The leather used for the entire hand section of glove, palm and back side, reinforcement patches, and welts (thumb, finger tips, and finger base), shall be cattlehide conforming to type V of KK-L-2004, The thickness of each leather component part shall be

15、not less than 2 1/2 ounces nor more than 3 1/2 ounces. The color of each leather component part shall be of a cream or light gray shade. component parts shall be of the same color. All leather * 3.3.1.2 Gauntlet section. The leather used for the gauntlet, front and back side of glove, shall be cattl

16、ehide conforming to type VI11 of KK-L-2004. ounces nor more than 3 1/2 ounces. a light gray shade. or the back of hand and back of gauntlet may be made of one piece of leather as specified in 3.3.1.1. The thickness of each piece shall be not less than 2 1/2 The color of each piece shall be of As an

17、alternate, the gauntlet may be one full piece * 3.3.2 unbleached cotton duck conforming to the requirements for type I, number 8, hard textured duck of CCC-C-419, or a gauntlet lining fabric composed of two thicknesses of unbleached cotton fabric securely laminated together. The laminated fabric sha

18、ll be composed of a cotton twill face fabric weighing not less than 3.7 ounces per square yard and a plain weave cotton backing fabric weighing not less than 1.7 ounches per square yard. The finished fabric (laminated) shall contain not less than 14 ounces per square yard of natural rubber, syntheti

19、c rubber, or synthetic resin, and weigh not less than 19.4 ounces per square yard (see 4.4.1). may be one piece or two pieces. Gauntlet lining Leather gauntlet piece shall be lined with an The gauntlet lining 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

20、 IHS-,-,-MIL-G-37465E 84 W 777770b 0383425 I MIL-G-19465E (NU) * 3.3.3 Hand liner. The yarn for the fabric face shall be 98.0 percent wool ofa grade not lower than U.S. Standard 50s (see 4.4.1). The fibers may be from fleece, pulled sheep, or any combination thereof. The use of reprocessed, revised

21、or waste wool is prohibited. 30.0 percent of the finished fabric weight. to the requirements specified in table I. The glove shall have a wool-cotton knitted fabric. The cotton backing yarn shall be no more than The scoured fabric shall comply Table I - PhysiGal requirements Requirement Characterist

22、ic Minimum Maximum Wales per inch Courses per inch Weight, ounces per square yard 17 20 17 - 9 11 3.3.4 Thread. The thread for seaming and stitching the glove shall be cotton, conforming to type lAl, 4-ply, ticket numbers 16 and 20, of V-T-276. 9: 3.3.5 and size label conforming to type III or IV, c

23、lass 4 of DDD-L-20, except that the label shall bear the following inscription and shall show fastness to laundering only: Label - Each glove shall be marked with a combination identification GLOVE, LEATHER, GAUNTLET, CHIPPER CONTRACT NO: DLA-000-00-0-0000 (EXAMPLE) STOCK NO: 8415-00-000-0000 (EXAMP

24、LE) SIZE : RH - LARGE (EXAMPLE) NAME OF CONTRACTOR: U.S. PROPERTY * 3.4 Design. The glove shall be a slip-on style, Gunn-cut; consisting of a gauntlet with fabric lining, a continuous thumb with a leather welt inserted in the seam, a finger base flap welt positioned at base of second and third finge

25、r fronts on palm-side of glove, leather welts at finger tips, a reinforcement patch on palm-side of gauntlet to palm-seam and on back side of glove, and a knitted liner positioned on inside back of glove from wrist edge to base of ingers. 3.4.1 Figure. Figure 1 is furnished for information purposes

26、only. To the extent of any inconsistencies between the written specification and the figure, the written specification shall govern. 4 c a e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-proper proportions to provide a good fitting glove conforming

27、 to finished measurements in table III. 3.6 Construction. 3.6.1 Stitches, seams, and stitchings. The stitch, seam, and stitching types specified in table II shall conform to PED-STD-751, type 401 is used, the chain effect or looper (underthread) shall be on the inside of the glove. Where stitch 3.6.

28、2 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in table II. 3.6.3 Thread breaks and ends of seams. Ends of all seams and stitching produced with 301 stitch type, when not caught in other seams or stitching, shall be backtacked not less than 1/2 inch. B

29、oth ends of all seams and stitching produced with 401 stitch type, when not caught in other seams or stitching, shall have a 1/2 to 3/4 inch chain extending beyond each end. Thread breaks (all stitch types) shall be secured by stitching on each side of break not less than 1/2 inch. Skipped stitches

30、or thread breaks (401 stitch type) may be repaired using 301 stitch type. 3.7 Manufacturing operations requirements. The glove shall be made in accordance with operations listed in table II. required to follow the exact sequence of operations shown provided that the finished glove is identical to th

31、at produced by following the sequence of operations listed In table II. The contractor is not 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-65E (NU) 7i rn al al e- k.ic au k al a al rl w O al u al .rl a al 5 Q ! k w 3 5 3 5 w O a P al u 3 u m lu

32、vi rl thin or weak area: -Seriously. affecting serviceability -Affecting serviceability, but not Three or more needle holes or pinholes Wrinkles : -Seriously affecting serviceability -Affecting serviceability, but not seriously seriously seriously seriously (Gauntlet Not type specified Lining) Any h

33、ole, cut, or tear Floats, loose ends, smashes, or clubs Any broken or missing pick or end Any mend in fabric (except restitchin of seams) (Knitted liner) Not type specified Any hole, cut, or tear Color Not as specified Color not uniform or shaded parts clearly All leather components in hand portion

34、of noticeable glove not of same color Cleanness Any spot or stain Thread ends - on outside: 1. More than one but not more than three 2. More than three not trimmed to trimmed to less than 112 inch less than 112 inch X X X X X X X X X X X X X X X X X 16 Provided by IHSNot for ResaleNo reproduction or

35、 networking permitted without license from IHS-,-,-MIL-G-174b5E 8L( = 9779706 0383438 T MIL-G-19465E (NU) Classification Examine Defect Major Minor Cutting Any component part not cut in accordance with specification requirements Components Any component part misplaced or not Any component part not s

36、ecurely affixed, serving intended purposes e.g., reinforcement patch on back side of glove loosely attached or knife cut Any workmanship damage, e.g., scissor Seams and Any open seam (except on gauntlet hem) NOTE: When one or more stitches are broken or two or more consecutive skipped stitches or a

37、runoff occurs on a single stitched seam or on both rows of stitching on a double stitched seam; it shall be classified as a major defect. When one or more stitches.are broken or two or more consecutive skipped stitches or a runoff occurs on only one row of a double stitched seam, it shall be classif

38、ied as a minor defect. St itching Open stitching on gauntlet hem NOTE: When one or more stitches on a line of stitching are broken or when two or more continuous skipped or runoff stitches occur Not specified seam or stitch type Any line of stitching omitted Any line of stitching misplaced or Loose

39、tension resulting in a loose seam not beginning or ending where specified X X X X X X X X X X 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-L7465E 84 7777706 0383437 L W Classification Examine Defect Major Minor Seams and Any part of glove

40、 caught in an unrelated Stitching operation (Cont d) Tight tension (stitches break or cutting of leather in the direction of the seam or stitching) stitch type, when not caught in other seams or stitching, backtacked less than 112 inch stitch type, when not caught in other seams or stitching, not ha

41、ving chain extending beyond each end stitch type, when not caught in other seams or stitching, having chain ex- tending less than 112 inch or more than 3/4 inch beyond each end less than 112 inch on either side of break the condition exists on the major por- tion of seam or stitching): Ends of stitc

42、hing produced with 301 Ends of stitching produced with 401 Ends of stitching produced with 401 Thread breaks (all stitch types) stitched Stitches per inch (to be scored only when 1. One or two stitches per inch less than the minimum 2. Three or more stitches per inch less than specified 3. More than

43、 the specified maximum number of stitches per inch, damaging leather 4. More than the specified maximum number of stitches per inch, but not damaging leather X X X X X X X Gage of stitching irregular or not as specified, seriously affecting service- ability X Gage of stitching irregular or not as sp

44、ecified, affecting serviceability but not seriously X 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-G-39i.165E i.1 m 7797906 0383i.140 I Classification Examine Defect Major Minor Assembly Any glove not neatly laid-off X detail Any finger o

45、r thumb distorted or twisted, affecting comfort of wearer X Not constructed with specified number of pieces of leather, knitted glove liner, and gauntlet linings X I Any reinforcement piece, i.e., patch, - flap or thumb welt missing, varying from specified dimension, or not completely caught in seam

46、 or stitching X . Label Omitted, incorrect, illegible, or (Marking) incomplete X Misplaced X 4.4.2.2 Dimensional examination. The glove shall be examined for dimensional defects. Any dimension that is not within the established tolerance, shall be classified as a defect (see 3.8). dimensional examin

47、ation, shall be as follows: Inspection AQLs Level Major Total ble to 4.4.2.1 II 2.5 6.5 I For defects applicable to 4. 4.2.2 s-3 - 4.0 I made to determine that packaging, packing, and marking complies with the Section 5 requirements of this specification. Defects shall be scored in accordance with t

48、he list below. container fully prepared for delivery except that it need not be closed. Defects of closure listed below shall be examined on shipping containers fully prepared for delivery. containers in the end item inspection lot. The inspection level shall be S-2 and the AQL shall be 2.5 defects

49、per 100 units. - The sample unit shall be one shipping The lot size shall be the number of shipping I 19 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-19465E (NU) Examine MIL-G-1711bSE BLt 7777706 038111111 T Defect Marking (exterior Omitted, incorrect, illegible, or improper size, and interior) location, sequence or method of