NAVY MIL-DTL-60292 B-2012 INITIATOR CARTRIDGE ACTUATED M99 ASSEMBLY《M99组件弹药驱动引爆器》.pdf

《NAVY MIL-DTL-60292 B-2012 INITIATOR CARTRIDGE ACTUATED M99 ASSEMBLY《M99组件弹药驱动引爆器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-60292 B-2012 INITIATOR CARTRIDGE ACTUATED M99 ASSEMBLY《M99组件弹药驱动引爆器》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMIL-DTL-60292B 6 January 2012 SUPERSEDING MIL-I-60292A 30 March 1990 DETAIL SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, M99 ASSEMBLY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requi

2、rements for the M99 Cartridge Actuated Initiator Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommen

3、ded for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Go

4、vernment documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMEN

5、T OF DEFENSE SPECIFICATIONS MIL-A-2550 Ammunition, General Specification For MIL-I-60525 Initiator, Cartridge Actuated, M99 Metal Parts Assembly MIL-I-82767 Initiator, Cartridge Actuated, M99 Remanufactured Metal Parts Assembly DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1168 Ammunition Lot Numbering An

6、d Ammunition Data Card MS28741 Hose Assembly, Detachable End Fitting, Medium Pressure (Copies of these documents are available online at https:/assist.daps.dla.mil/ or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia PA 19111- 5094.) Comments, suggestions,

7、 or questions on this document should be addressed to DEPARTMENT OF THE NAVY, Indian Head Division, NSWC, Code E12AP, Document Control, 4123 Artisans Court, Suite 103, Indian Head, Maryland 20640-5085, OFFICIAL BUSINESS, or emailed to amanda.pennnavy.mil. Since contact information can change, you ma

8、y want to verify the currency of this information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 1377 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

9、rom IHS-,-,-MIL-DTL-60292B 2 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or c

10、ontract. DRAWINGS NAVAL ORDNANCE STATION, INDIAN HEAD, MD (CAGE CODE 19200 and 19203) 8597230 Cartridge, Impulse, M91 Assembly DL10520405 Initiator, Cartridge Actuated, M99, Assembly 8830984 Box, Fiberboard (Inner) Packing, Ammunition for Initiator, Cartridge Actuated M27, M86, M87, M98, M99, or XM1

11、07 8830985 Box, Packing, Ammunition for Initiator, Cartridge Actuated M27, M86, M87, M98, M99, or XM107 9241155 Box, Fiberboard (Outer) Alternative, Packing Ammunition for Initiator, Cartridge Actuated, M27, M86, M87, M98, M99, or XM107 (Application for copies should be addressed to DEPARTMENT OF TH

12、E NAVY, Indian Head Division, NSWC, Code E12P, Document Control, 4123 Artisans Court, Suite 103, Indian Head, Maryland 20640-5085, OFFICIAL BUSINESS.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the

13、 issues of these documents are those cited in the solicitation or contract. American National Standards Institute (ANSI)/American Society For Quality (ASQ) ANSI/ASQ Z1.4 Sampling Procedures and Tables for Inspection by Attributes (DoD adopted) ASQ A8402 Quality Management and Quality Assurance Vocab

14、ulary (Copies of this document are available online at http:/www.asq.org/, or from the American Society for Quality, PO Box 3005, 611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) American Society For Testing And Materials (ASTM) ASTM E1742/E1742M Standard Practice for Radiographic Examination (Copi

15、es of this document are available online at http:/www.astm.org/ or from the American Society for Testing and Materials Customer Service, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict bet

16、ween the text of this document and the references cited herein, the text of this document takes Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60292B 3 precedence. Nothing in this document, however, supersedes applicable laws and regulations

17、 unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. All materials used in the manufacture of the initiators shall conform strictly to the specifications referred to on the respective drawings unless specific approval in writing covering a departure therefrom has been obtai

18、ned from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.2 Primary components. For the purpose of this specification, the M91 delay cartridge (

19、Drawing 8597230) is defined as a primary component. Only primary components from a single lot shall be used in a production lot of initiators. One primary component production lot may be used in more than one initiator production lot. 3.3 Breakaway torque. The chamber and cap of the assembled initia

20、tor shall withstand a breakaway torque application of 400 inch pounds without loosening or deformation (see 4.2.3.1). 3.4 Residual magnetism. The initiator shall not deflect the indicator of the compass more than five degrees in either direction using procedure 4.2.3.2. 3.5 Firing pin release. The f

21、iring pin of the assembled initiator, less safety pin, cartridge and chamber shall release from the cocked position when the application of an axial load of 18 to 25 pounds has withdrawn the initiator pin 0.370 inch, minimum, and 0.425 inch, maximum (see 4.2.3.3). 3.6 Initiator pin security. Applica

22、tion of an axial load of 200 to 220 pounds to the initiator pin of the assembled initiator shall not withdraw the initiator pin past the safety pin. Load application shall cause no permanent deformation of the safety pin (see 4.2.3.4). 3.7 Functional (see 4.2.3.5). 3.7.1 Ballistics. Initiators loade

23、d with cartridges from one accepted lot and temperature conditioned shall perform within the pressure values and ignition delay time (see 6.6.2) specified in table I. Pressure values shall be recorded at the end of 15 feet of aircraft hose, assembly number MS28741-4, and a pressure chamber with a vo

24、lume of 1 cubic inch. TABLE I. Pressure values. Temperature (F) Pressure (psi) Ignition delay time, max (ms) See 6.7.2) Minimum Maximum -60 to -70 500 1425 65 65 to 75 600 1550 65 195 to 205 700 1700 65 3.7.2 Misfires. There shall be no misfires. 3.7.3 Mechanical failures. The initiator shall functi

25、on without mechanical failure (see 6.6.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60292B 4 3.8 Workmanship. Initiators shall be free of cracks, splits, incomplete or damaged threads on inlet and outlet ends, or other defects which mi

26、ght prevent proper mating with connecting parts or proper functioning of the device. 3.8.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.8.2 Burr. No part shall have a burr which might interfere with the assembly or functi

27、on of the item or which might be injurious to personnel handling the item. 3.8.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion, or other foreign matter. 3.9 Radiographic examination. Each initiator assembly shall be radiographically examined for defects as sp

28、ecified in 4.4. 3.10 Component parts. All component parts shall meet the requirements of MIL-I-60525 or MIL-I-82767 prior to assembly. 4. VERIFICATION 4.1 Quality assurance terms and definitions. Reference shall be made to ASQ A8402 to define the quality assurance terms used. 4.1.1 Inspection. Inspe

29、ction shall be in accordance with MIL-A-2550. 4.2 Inspection provisions. 4.2.1 Lot. 4.2.1.1 Submission of product. Unless otherwise specified by the contracting officer, formation of lots and presentation of lots shall be in accordance with the “Submission of Product“ provisions of ASQ Z1.4. 4.2.1.2

30、 Size of lot. A lot shall consist of an identifiable group of assembled initiators containing metal parts assemblies produced by a homogeneous process and loaded with one lot of accepted cartridges. 4.2.2 Examination. One-hundred percent examination shall be performed for all critical defects. Exami

31、nation for major and minor defects shall be performed in accordance with the classification of defects. Four power (4X) magnification may be used for inspection of such defects as burr and foreign matter. When compliance with the applicable requirement is in doubt as a result of visual examination,

32、the characteristic shall be measured or gaged to determine acceptability. All nonconforming material shall be rejected. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60292B 5 4.2.2.1 Cartridge, Impulse Delay, M91, Drawing 8597230, covering

33、a detail of Drawing 10520405. Characteristic Defect Method of Inspection Critical 1 Mixed cartridges Visual 2 Metal defective Visual 3 Marking missing, incorrect, or illegible Visual Major 101 Foreign matter present Visual Minor 201 Case scratched, wrinkled, bulged, or dented Visual 202 Varnish miss

34、ing or inadequate Visual 4.2.2.2 Assembly, Drawing 10520405, less all drawings except 10520410, 10520411, and MS 19060-3. Critical 1 Protrusion of firing pin Gage 2 Steel ball missing Gage 3 Striker hole in firing pin housing obstructed Visual Major 101 Burr Visual 102 Foreign matter present Visual

35、Minor None defined 4.2.2.3 Assembly, Drawing 10520405, less Drawings 8597230, 10520407, 10520496, 10520414, and MIL-C-5501/11. Critical 1 Firing pin not cocked Visual/Manual 2 Any parts missing Visual 3 Improper assembly Visual Major 101 Safety pin loose or deformed Visual 102 Burr Visual 103 Foreig

36、n matter present Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60292B 6 Minor None defined 4.2.2.4 Assembly, Drawing 10520405, less all Drawings, except 10520407, 10520414, and 8597230. Critical 1 Cartridges not properly seated Visua

37、l 2 Filter missing or insecure Visual 3 Nylon patch missing or improperly applied Visual Major 101 Burr Visual 102 Foreign matter present Visual Minor None defined 4.2.2.5 Assembly, Drawing 10520405. Critical 1 Cartridge face not seated against base of X-ray firing pin housing 2 Any part missing exc

38、ept as otherwise Visual/X-ray classified 3 Improper assembly Visual/X-ray 4 Marking missing, incomplete, or illegible Visual Major 101 Set screw missing or insecure Visual 102 Burr Visual 103 Foreign matter present Visual Minor 201 Thread sealing compound missing from set Visual screws 202 Protectiv

39、e cap missing Visual 203 Protective finish inadequate or defective Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60292B 7 4.2.2.6 Box, Fiberboard (Inner) Ammunition Packing Drawing 8830984. Critical None defined Major None defined Mi

40、nor 201 Contents loose Manual 202 Box damaged Visual 203 Sealing strip missing, improperly applied Visual 204 Marking missing, incorrect, or illegible Visual 205 Cut, damaged, or improperly sealed bag Visual 4.2.2.7 Box, Ammunition Packing, Drawing 8830985. Critical None defined Major None defined M

41、inor 201 Contents loose Manual 202 Strapping missing, loose, broken, or Manual/Visual improperly assembled 203 Contents of box exposed Visual 204 Box damaged Visual 205 Marking missing, incorrect, or illegible Visual 206 Number of units, incorrect Visual 4.2.2.8 Box, Fiberboard (Outer) Alternative A

42、mmunition Packing, Drawing 9241155. Critical None defined Major None defined Minor Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60292B 8 201 Contents loose Manual 202 Box broken or damaged Visual 203 Number of units contained incorrect Vis

43、ual 204 Marking missing, incorrect, or illegible Visual 205 Tape incomplete Visual 4.2.3 Inspection testing. The Following tests shall be performed in accordance with the provisions of 4.3. 4.2.3.1 Breakaway torque. Each assembly shall be subjected to the breakaway torque test of the threaded joint

44、between the cap and the chamber. Failure of any assembly to comply with the requirements of 3.3 shall be cause for rejection of the initiator. 4.2.3.2 Residual magnetism. Each initiator shall be subjected to the test for excessive residual magnetism as specified in 4.3.2. Failure of any initiator to

45、 comply with the requirement of 3.4 shall be cause for rejection of the initiator. 4.2.3.3 Firing pin release. The initiator pin of each subassembly, consisting of all parts, except the safety pin, cartridge, and chamber, shall be subjected to the firing-pin release test. Failure of any subassembly

46、to comply with the requirements of 3.5 shall be cause for rejection of the subassembly. To achieve the pull force requirement of 18-25 pounds specified in 3.5 selective reassembly may be necessary (i.e., changing initiator pins or springs) for those assemblies which are out of range. 4.2.3.4 Initiator pin security. The i