NAVY MIL-C-24491 B (1)-1986 CONTAINER FIBERGLASS REINFORCED PLASTIC FOR INFLATABLE LIFEBOATS MARK 5 MOD 2 AND MARK 6《MARK 5 MOD 2 和MARK 6气胀式救生艇纤维玻璃塑料增强集装箱》.pdf

《NAVY MIL-C-24491 B (1)-1986 CONTAINER FIBERGLASS REINFORCED PLASTIC FOR INFLATABLE LIFEBOATS MARK 5 MOD 2 AND MARK 6《MARK 5 MOD 2 和MARK 6气胀式救生艇纤维玻璃塑料增强集装箱》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-24491 B (1)-1986 CONTAINER FIBERGLASS REINFORCED PLASTIC FOR INFLATABLE LIFEBOATS MARK 5 MOD 2 AND MARK 6《MARK 5 MOD 2 和MARK 6气胀式救生艇纤维玻璃塑料增强集装箱》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、c-/5-,$sa MIL-C-2449 AMENDMENT 1 29 January 1986 I. MILITARY SPECIFICATION CONTAINER, FIBERGLASS REINFORCED PLASTIC, FOR INFLATABLE LIFEBOATS, MARK 5, MOD 2, AND MARK 6 This amendment forms a part of MIL-C-24491B(S), dated 21 April 1981, and is approved for use within the Naval Sea Systems Command,

2、Department of the Navy and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1: Delete and substitute: “2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and stan- dards form a part of this specification to the extent

3、 specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation.“ At the bottom of the page: Delete and substitute: I Benefici

4、al comments (recommendations, additions, deletions) and any pertinent data which may be ofuse in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the- Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Imp

5、rovement Proposal (DD Form 1426) appearing at the end of this document or by letter. n AMSC NIA FSC 1940 DISTRIBUTION STATEMENT A Approved for public release; distributiqn unlimited 1 of 5 - I .- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-

6、C-ZLlYSLB (3) 37 9 7777906 0373072 7 9 MIL-C-24491B(SH) AMENDMENT 1 ) PAGE 2 Line 11, after Military Standards: Add the following paragraph: “2.1.2 Government drawing. The following Government drawing forms a part of this specification to the extent specified herein. Unless otherwise specified, the

7、issue shall be that in effect on the date of the solicitation.“ Line 14, after Drawing: Delete and substitute: “(Copies of specifications, standards, and drawings required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed

8、 by the contracting activity.)“ 2.2: Delete and substitute: “2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDIS

9、S specified in the solicitation. issues of documents not listed in the DoDISS shall be the issue of the nongovern- ment documents which is current on the date of the solicitation.“ Unless otherwise specified, the 2.2, lines 8 and 9: Delete “1616 “P“ Street, N.W., Washington, DC 20036.)“ and substitu

10、te “2200 Mill Road, Alexandria, VA 22314.)“ 2.2, lines 13, 14, and 15: Delete and substitute: “(Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries

11、or other informational services.)“ Add the following paragraph: “2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specifi- c

12、ation shall take precedence. Nothing in this specification, however, shall . supersede applicable laws and regulations unless a specific exemption has been obtained.“ 3.1: Delete and substitute: “3.1 First article. -When specified in the contract or purchase order, a sample shall be subjected to fir

13、st article inspection (see 4.3 and 6.3).“ 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-24491B(SH) AMENDMENT 1 PAGE. 3 3.2.1: Delete and substitute: “3.2.1 Recovered materials. Unless otherwise specified herein, all equipment, material, and

14、 articles incorporated in the products covered by this specification shall be new and may be fabricated using materials produced from recovered materials to the maximum extent practicable without jeopardizing the intended use. The term *recovered materials“ means materials which have been collected

15、or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. interpreted to mean that the use of used or rebuilt products is allowed under this specification unless otherwise specifically specified.“ None of the above shall be PAGE 4 3.3.7: D

16、elete and substitute: “3.3.7 Joint seal. The joint between the top and bottom halves of the container shall be covered with a 6-inch wide rubber band seal, B.F. Goodrich part number IRA 1056, or equal. securing bands shall be attached.“ After the sealing band is in place, the brass PAGE 5 4.1: Delet

17、e and substitute: “4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. in the contract or purchase order, the contractor may use his own or any other fac

18、ilities suitable for the perf ormance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services

19、conform to prescribed requirements.“ Except as otherwise specified 4.1.1: Delete and substitute: “4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection sy

20、stem or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality confo

21、rmance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material.“ P Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-24473B (3) 37 W 7777906 0373

22、074 O W MIL-C-24491B(SH) AMENDMENT 1 ) Add the following paragraph: “4.1.2 Inspection system. The contractor shall provide and maintain an inspection system in accordance with the data ordering documents included in the contract or order (see 6.2.2).“ PAGE 7 4.7: Delete and substitute: “4.7 Inspecti

23、on of packaging. Sample packages and packs, and the inspection of the preservation-packaging, packing and marking for shipment and storage shall be in accordance with the requirements of section 5 and the documents specified therein. * 5.: Delete and substitute: * 5 . PACKAGING (The packaging requir

24、ements.specified herein apply only for direct Govern- ment acquisition. of referenced documents listed in section-2, see 6.4).“ For the extent of applicability of the packaging requirements PAGE 8 6.2.2: Delete and substitute: “6.2.2 Data requirements. When this specification is used in an acquisi-

25、tion and data are required to be delivered, the data requirements identified below shall be developed as specified by an approved Data Item Description (DD Form 1664) and delivered in accordance with the approved Contract Data Require- ments List (CDRL), incorporated into the contract. When the prov

26、isions of DoD FAR Supplement, Part 27, Sub-Part 27.410-6 (DD Form 1423) are invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with the contract or purchase order requirements. Deliverable data required by this specification are cite

27、d in the following paragraphs. . Paragraph no. Data requirement title Applicable DID no. Opt ion 4.1.2 Inspection system program plan 4.3.1 First article inspection report - DI-R-4803 DI-T-4902 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-

28、2qLI7LB (11) 117 m 7977706 01173075 2 m t MIc-C-24491B(SH) AMENDMENT 1 PAGE 9 Lines 1, 2, and 3: Delete and substitute: “(Data item descriptions related to this specification, and identified in section 6 will be approved and listed as such in DoD 5000.19L., Vol. II, AMSDL. Copies of data item descri

29、ptions required by the contractors in connection with specific acquisition functions should be obtained from the N.aval Publications and Forms Center or as directed by the contracting officer.)“ 6.3: Delete and substitute: “6.3 First article. When a first article inspection is required, the item sho

30、uld be a first article sample. The first article should consist of one unit. The contracting officer should include specific instructions in acquisition docu- ments regarding arrangements for examinations, approval of first article test results and disposition of first articles. Invitations for bids

31、 should provide that the Government reserves the right to waive the requirements for samples for first article inspection to those bidders offering a product which has been pre- viously acquired or tested by the Government, and that bidders offering such products, who wish to rely on such production

32、 or test, must furnish evidence with the bid that prior Government approval is presently appropriate for the pending contract . “ 6.4: Delete and substitute: “6.4 Sub-contracted material and parts. The packaging requirements of referenced documents listed in section 2 do not apply when material and

33、parts are acquired by the contractor for incorporation into the equipment and lose their separate identity when the equipment is shipped.“ 6.5: Delete and substitute: “6.5 Changes from previous issue. Asterisks are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. “ Preparing activity: Navy - SH (Project 1940-N062) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-