FORD WSS-M64J42-A1-2017 EC ADDITIVE BIOCIDE SOLUTION BRONOPOL AND OCTYLISOTHIAZOLINONE MIXTURE TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M64J42-A1-2017 EC ADDITIVE BIOCIDE SOLUTION BRONOPOL AND OCTYLISOTHIAZOLINONE MIXTURE TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M64J42-A1-2017 EC ADDITIVE BIOCIDE SOLUTION BRONOPOL AND OCTYLISOTHIAZOLINONE MIXTURE TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2017 01 27 Released A. Reilly, Y. Langwald, FOE Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 EC ADDITIVE, BIOCIDE SOLUTION, BRONOPOL AND WSS-M64J42-A1 OCTYLISOTHIAZOLINONE MIXTURE EC ADDITIV

2、E, BIOCIDE SOLUTION, BRONOPOL, WSS-M64J42-A2 CHLOROMETHYLISOTHIAZOL AND METHYLISOTHIAZOL MIXTURE EC ADDITIVE, BIOCIDE SOLUTION, CHLOROMETHYLISOTHIAZOL AND WSS-M64J42-A3 METHYLISOTHIAZOL MIXTURE 1. SCOPE The materials defined by this specification are an aqueous solution of biodegradable biocides. 2.

3、 APPLICATION This specification was released originally for materials to control the level of biological infestation and growth in cathodic electrocoat primers. 2.1 LIMITATIONS The materials shall only be used, as specified by the supplier. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification req

4、uires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials E

5、ngineer. 3.2 COMPOSITION Aqueous solution of biocides, compatible with electrocoat process system. 3.2.1 Active Substances WSS-M64J42-A1: Mixture of bronopol and octylisothiazolinone. WSS-M64J42-A2: Mixture of bronopol, chloromethylisothiazol and methylisothiazol. WSS-M64J42-A3: Mixture of chloromet

6、hylisothiazol and methylisothiazol. 3.3 PHYSICAL PROPERTIES 3.3.1 Color Colorless Light Yellow ENGINEERING MATERIAL SPECIFICATION WSS-M64J42-A1,A2,A3 Copyright 2017, Ford Global Technologies, LLC Page 2 of 3 3.3.2 Density (ASTM D1475) WSS-M64J42-A1: Mixture of bronopol and octylisothiazolinone. 1.16

7、1 -1.173 g/ml WSS-M64J42-A2: Mixture of bronopol, chloromethylisothiazol and 1.072 -1.092 g/ml methylisothiazol. WSS-M64J42-A3: Mixture of chloromethylisothiazol and 1.025 -1.260 g/ml methylisothiazol. 3.3.3 Refractive Index (ASTM D1218) WSS-M64J42-A1: Mixture of bronopol and octylisothiazolinone. 1

8、.455 -1.467 WSS-M64J42-A2: Mixture of bronopol, chloromethylisothiazol and 1.345 -1.357 methylisothiazol. WSS-M64J42-A3: Mixture of chloromethylisothiazol and 1.267 -1.549 methylisothiazol. 3.3.4 Flash Point, C (ISO 2719) WSS-M64J42-A1: Mixture of bronopol and octylisothiazolinone. As per Initial Sa

9、mple WSS-M64J42-A2: Mixture of bronopol, chloromethylisothiazol As per Initial Sample and methylisothiazol. WSS-M64J42-A3: Mixture of chloromethylisothiazol and As per Initial Sample methylisothiazol. 3.3.5 Volatile Organic Content, range % (ASTM D3960) WSS-M64J42-A1: Mixture of bronopol and octylis

10、othiazolinone. As per Initial Sample WSS-M64J42-A2: Mixture of bronopol, chloromethylisothiazol and As per Initial Sample methylisothiazol. WSS-M64J42-A3: Mixture of chloromethylisothiazol and As per Initial Sample methylisothiazol. 3.5 QUALITY When these additives are used with electrocoat primer,

11、the resulting bath material must meet all requirements of the affected material specification. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Spe

12、cifications. 4.1 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a quali

13、fied and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated

14、quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. ENGINEERING MATERIAL SPECIFICATION WSS-M64J42-A1,A2,A3 Copyright 2017, Ford Global Technologies, LLC Page 3 of 3 4.2 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalen

15、t in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Techn

16、ical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specificati

17、ons for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.3 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS