FORD WSD-M1C244-A-2010 GREASE LITHIUM SOAP NLGI 1 TO BE USED WITH FORD WSS-M99P1111-A 《锂皂润滑脂 美国润滑脂协会1 与福特WSS-M99P1111-A 一起使用》.pdf

《FORD WSD-M1C244-A-2010 GREASE LITHIUM SOAP NLGI 1 TO BE USED WITH FORD WSS-M99P1111-A 《锂皂润滑脂 美国润滑脂协会1 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享，可在线阅读，更多相关《FORD WSD-M1C244-A-2010 GREASE LITHIUM SOAP NLGI 1 TO BE USED WITH FORD WSS-M99P1111-A 《锂皂润滑脂 美国润滑脂协会1 与福特WSS-M99P1111-A 一起使用》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 09 27 Revised See summary of revisions paragraph 5. L. Schmalz, NA 2004 04 29 Revised Para 3.0 inserted; para 3.1, 3.2, 3.3, 3.6 & 4 deleted 1993 01 21 Released C10271616 P.A.Osman Printed copies are uncontrolled Copyright 2010, Ford Glob

2、al Technologies, LLC Page 1 of 3 GREASE, LITHIUM SOAP, NLGI 1 WSD-M1C244-A 1. SCOPE The material defined by this specification is a grease consisting of mineral oil and lithium soap and other additives to give the desired characteristics. 2. APPLICATION This specification was released originally for

3、 grease used to lubricate plastic parts in transmission shifting systems operating between -40 and 130 C. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111

4、-A). 3.2 COLOR Beige (Visual) 3.3 WORKED PENETRATION, tenths of a millimeter 310-340 (ASTM D 217, DIN ISO 2137, 60 stroke) 3.4 DROPPING POINT, 250 C, min (ASTM D 566 or ASTM D 2265, DIN ISO 2176) 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meet

5、ing the requirements of this specification. Grease approved to this specification should have the following typical properties. 4.1 LITHIUM SOAP CONTENT, 5-10% (ASTM D 128) 4.2 MINERAL OIL 20-30% SYNTHETIC HYDROCARBON 60-70% (ASTM D 128) 4.3 MINERAL OIL (ASTM D 445, DIN 51562) 4.3.1 Viscosity At 40

6、oC, 730 mm2/sec, min 4.3.2 Viscosity At 100 oC, 60 mm2/sec, min ENGINEERING MATERIAL SPECIFICATIONWSD-M1C244-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 3 4.4 PENETRATION, tenths of a millimeter (ASTM D 217, DIN ISO 2137) Prolonged Worked Penetration, 10

7、0,000 strokes +/- 15% change from 60 stroke result 4.5 OXIDATION STABILITY, (ASTM D 942, 100 hr at 99 C, or DIN 51808) 0.3 kPa,max 4.6 EMCOR CORROSION (ASTM D 6138, DIN 51802, 168 hrs) Distilled water 1 max 4.7 WATER WASHOUT, 10%, max (ASTM D 1264, at 38 C, DIN 51807 T02) 4.8 OIL SEPARATION, 5%, max

8、 (ASTM D 1742 or Federal Standard 791C, Method 321.3, DIN 51817) 4.9 INTERFACE COMPATIBILITY Production representative materials specific to the application should be used for the following tests. 4.9.1 Chemical Attack to Painted Surfaces (FLTM BJ 126-01) Not tested for initial application of this g

9、rease. Grease must be tested for chemical attack to painted surfaces when used for additional applications that come in contact with paint surfaces, ex. E-coat and powder coat. 4.9.2 Resistance to Stress Cracking (FLTM BO 127-03) Not tested for initial application of this grease. Grease must be test

10、ed for resistance to stress cracking when used for additional applications that come in contact with polymers such as PC, ABS, PC+ABS, ASA or acrylic. 4.9.3 Elastomer Compatibility (ASTM D 4289, 70 h, 100 C, DIN 53505, DIN 53504) Volume change 0-10% Hardness change, max +/- 10% Tensile Strength chan

11、ge -50% Note: Tested on Freudenberg 72 NBR 902, 75 ACM 370, 75 FPM 595 and 81 VMQ 541 elastomers. ENGINEERING MATERIAL SPECIFICATIONWSD-M1C244-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 3 of 3 5 SUMMARY OF REVISIONS 2010 09 27 Deleted: 3.1.1 - Initial Qualifications 3.1.2 - Ongoing Verification Plan 3.4 - Consistency 3.5 - Functional Approval 5.1 - Typical Properties 5.2 - Suppllement C Added: 3.1-3.4 - Requirements 4.1-4.9 - General Information