FORD ESE-M99C89-A-2009 LUBRICANT - MINERAL OIL AND CELLULOSE FIBERS TO BE USED WITH FORD WSS-M99P1111-A 《矿物油和纤维素纤维润滑剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD ESE-M99C89-A-2009 LUBRICANT - MINERAL OIL AND CELLULOSE FIBERS TO BE USED WITH FORD WSS-M99P1111-A 《矿物油和纤维素纤维润滑剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD ESE-M99C89-A-2009 LUBRICANT - MINERAL OIL AND CELLULOSE FIBERS TO BE USED WITH FORD WSS-M99P1111-A 《矿物油和纤维素纤维润滑剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 11 17 N-STATUS No known use. No replacement named D. DiGregorio, NA 2004 02 24 Revised Para 3.0 Inserted; paras 3.3, 4 deleted 1974 01 22 Released E3D-012482 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Pa

2、ge 1 of 2 LUBRICANT - MINERAL OIL AND CELLULOSE FIBERS ESE-M99C89-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is an extrudable compound composed of a mixture of mineral oil and cellulose fibers. 2. APPLICATION This specification was released originally for lub

3、ricant designed for lubricating distributor shaft bearings. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1 REQUIREMENTS FOR FINISHED PRODUCT 3.1

4、.1 Cellulose Fibers Content, by weight 13% - 17% (ASTM D 128) 3.1.1.1 The materials should contain a mixture of 80% - 90% ground wood fibers and 10% - 20% sulfite fibers. Average fiber length should be 1.0 mm with 75% between 0.25 mm - 1.5 mm. 3.1.2 Oil Content, by weight 83% - 87% (ASTM D 128) 3.1.

5、3 Moisture Content, by weight max 1.0% (ASTM D 128) 3.2 REQUIREMENTS FOR OIL 3.2.1 Viscosity (ASTM D 445) 3.2.1.1 At 37.8 C 84 - 87.5 cSt (mm2/s) 3.2.1.2 At 98.9 C 9.65 - 10.22 cSt (mm2/s) 3.2.2 Viscosity Index, min 95 (ASTM D 2270) ENGINEERING MATERIAL SPECIFICATIONESE-M99C89-A Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, LLC Page 2 of 2 3.2.3 Flash Point, min 241 C (ASTM D 92) 3.2.4 Pour Point, max -18 C (ASTM D 97) 3.2.5 Total Acid Number, max 0.15 (ASTM D 974) 3.2.6 Copper Corrosion, max lb (ASTM D 130)