FORD ESB-M12G70-A2-2012 BATT THERMAL INSULATION MINERAL FIBER NEEDLED TO BE USED WITH FORD WSS-M99P1111-A 《隔热针刺矿物纤维垫 与福特WSS-M99P1111-A 一起使用》.pdf

《FORD ESB-M12G70-A2-2012 BATT THERMAL INSULATION MINERAL FIBER NEEDLED TO BE USED WITH FORD WSS-M99P1111-A 《隔热针刺矿物纤维垫 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M12G70-A2-2012 BATT THERMAL INSULATION MINERAL FIBER NEEDLED TO BE USED WITH FORD WSS-M99P1111-A 《隔热针刺矿物纤维垫 与福特WSS-M99P1111-A 一起使用》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 01 18 N Status No replacement named. N. Benipal, NA 2006 02 16 Revised Inserted 3.0; Deleted 3.1, 3.13 and 4 1975 02 15 Released AE1-6000-171 Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC Page 1 of

2、3 BATT, THERMAL INSULATION, MINERAL FIBER, NEEDLED ESB-M12G70-A2 NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a soft, flexible sound and thermal insulation batt composed of mineral fibers suitable for high temperature insulation up to 1260 C in non-load bearin

3、g areas. 2. APPLICATION This specification was released originally for material used as a floor pan heat insulator under the seat and over the catalytic converter of the 1975 Granada and Monarch where the floor covering is not subject to load deflection. This material has poor resistance to flexing

4、and must not be used in load bearing areas. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Produ

5、ction Materials (WSS-M99P1111-A). 3.2 CONSTRUCTION This insulation batt is composed of mineral fibers needled and heat set without resins to provide a uniform insulating surface. 3.3 COMPOSITION Mineral Fibers (Alumina and Silica) 99% by weight Test Method: Cut 10 g of sample into a previously ignit

6、ed and weighed porcelain crucible. Condition at 102 +/- 3 C for 3 h. Record the weight. Heat in muffle furnace at 816 +/- 28 C for 4 h. Cool, weigh and calculate % mineral fiber on basis of retained weight. 3.4 DENSITY, + 20%, - 10% 5.0 lb/ft3 (80 kg/m3) (ASTM C 167 except compute thickness from 12

7、x 12 in (305 x 305 mm) sample with 0.5 psi (3.4 kPa) loading) 3.5 THICKNESS (FLTM BN 023-02) As specified on engineering drawing. ENGINEERING MATERIAL SPECIFICATION ESB-M12G70-A2 Copyright 2012, Ford Global Technologies, LLC Page 2 of 3 3.6 HEAT STABILITY Shrinkage at 980 C, max 1.9% Test Method: Cu

8、t two 12 x 1 in (305 x 25 mm) strips from the center of the specimen, one in each direction. Measure the strips to the nearest 0.01 in (0.25 mm). Place strips in a muffle furnace for 4 h at 980 +/- 28 C. Cool specimen to 23 +/- 2 C and measure the strips. Calculate the heat shrinkage from the change

9、 in length. 3.7 SOUND ABSORPTION, % min (ASTM C 384, 0.5 in (13 mm) thick, % absorptions were obtained at the first minimum for the following frequencies:) 250 Hz 6% 500 Hz 30% 1000 Hz 20% 3000 Hz 75% 5000 Hz 90% 3.8 THERMAL CONDUCTIVITY, max (ASTM C 177) 24 C mean temperature k = 0.24 ( = 0.03) 3.9

10、 COMPRESSION AND RECOVERY (FLTM BN 015-02, plied to 1 in (25 mm) thickness) Compression, max 60% Recovery, min 30% 3.10 FLAMMABILITY REQUIREMENT In order to comply with Federal Motor Vehicle Safety Standard No. 302, the materials, portions of components, and composites shall not burn, or transmit a

11、flame across its surface, at a rate of more than 4 in (101 mm) per minute. To demonstrate compliance, the sample size and method of testing shall be in accordance with FLTM BN 024-02. ENGINEERING MATERIAL SPECIFICATION ESB-M12G70-A2 Copyright 2012, Ford Global Technologies, LLC Page 3 of 3 3.11 PERF

12、ORMANCE, ENVIRONMENTAL AGING REQUIREMENT All materials, portions of components, and composites defined by this specification that have not been treated, modified or reformulated and exceed a maximum burn rate of 3.0 in (76 mm) per minute as specified by the Flammability Lot Sampling Plan of FLTM BN

13、024-02, must be evaluated for permanency of the materials flame retardant properties per ESB-M25P3-A according to the accelerated environmental aging requirements applicable to the basic material category of this particular specification. Any material, portions of components, and composites defined

14、by this specification that have been treated, modified or reformulated to conform to Flammability Lot Sampling Plan of FLTM BN 024-02, regardless of maximum burn rate, must be evaluated for both permanency of materials flame retardant properties and changes in mechanical, chemical and physical prope

15、rties per ESB-M25P3-A applicable to the basic materials category of this particular specification. 3.12 FLAMMABILITY TEST PROGRAM Materials, portions of components, and composites governed by this specification must also comply with the requirements of ES-D3AB-11014-AA. 5. GENERAL INFORMATION The in

16、formation given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 CONSTRUCTION Fiber diameter 4.0 +/- 0.5 microns Fiber length 1.0 +/- 0.5 in (25 +/- 13 mm) 5.2 THERMAL CONDUCTIVITY (ASTM C 177) Mean temperature 260 C k = 0.5 ( = 0.07) 538 C k = 0.9 ( = 0.13) 816 C k = 1.6 ( = 0.23)