FORD ESB-M12G65-A-2012 BATT GLASS FIBER SOUND ABSORPTION LONG FIBER 2-1 2 LB FT3 (40 KG M3) TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESB-M12G64-A)《2-1 2LB FT3(40 KG M3).pdf

《FORD ESB-M12G65-A-2012 BATT GLASS FIBER SOUND ABSORPTION LONG FIBER 2-1 2 LB FT3 (40 KG M3) TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESB-M12G64-A)《2-1 2LB FT3(40 KG M3).pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M12G65-A-2012 BATT GLASS FIBER SOUND ABSORPTION LONG FIBER 2-1 2 LB FT3 (40 KG M3) TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESB-M12G64-A)《2-1 2LB FT3(40 KG M3).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 03 2012 01 18 N Status No replacement named N. Benipal, NA 2006 11 02 Revised Inactivated and removed ESB-M12G64-B, no replacement named R. Lord 1965 05 19 Released Released ESB-M12G64-A and ESB-M12G65-A AVI 903 Controlled document at www

2、.MATS Copyright 2012, Ford Global Technologies, LLC Page 1 of 4 BATT GLASS FIBER SOUND ABSORPTION, LONG FIBER, ESB-M12G64-A 1-1/2 LB/FT3 (24 KG/M3) BATT GLASS FIBER SOUND ABSORPTION, LONG FIBER, ESB-M12G65-A 2-1/2 LB/FT3 (40 KG/M3) ESB-M12G65-B NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material def

3、ined by these specifications is made of glass fibers, bonded with a thermosetting resin and compressed into a flexible blanket. 2. APPLICATION These specifications were released originally for material used as an engine compartment heat and sound absorber. 3. REQUIREMENTS Material specification requ

4、irements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 DENSITY, +/- 15% (ASTM C 167, except base calcula

5、tions on nominal thickness as specified on engineering drawings) ESB-M12G64-A 1-1/2 lb/ft3 (24 kg/m3) ESB-M12G65-A/ B 2-1/2 lb/ft3 (40 kg/m3) 3.3 CONSTRUCTION 3.3.1 Fiber Diameter 0.00028 - 0.00056 in (0.0071 - 0.0142 mm) Test Method: Measure the diameter of 10 fibers using a calibrated microscope o

6、r other suitable means and report the average value. 3.3.2 Binder Content 30 +/- 5% phenol formaldehyde Test Method: Cut 1-2 g of sample into a previously ignited porcelain crucible. Condition at 102 +/- 3 C for 3 h. Record weight. Heat in a muffle furnace at 538 +/- 28 C until binder is burned off.

7、 Cool, weigh and calculate % binder on basis of conditioned weight (step #2). ENGINEERING MATERIAL SPECIFICATION ESB-M12G64-A ESB-M12G65-A/B Copyright 2012, Ford Global Technologies, LLC Page 2 of 4 3.4 BREAKING STRENGTH, min (ASTM D 1682, Grab Method, samples 0.75 in (19.1 mm) thick x 4 in (100 mm)

8、 wide x 6 in (150 mm) long). 3.4.1 ESB-M12G64-A WMD 15 lb (67 N) AMD 15 lb (67 N) 3.4.2 ESB-M12G65-A/ B WMD 40 lb (178 N) AMD 40 lb (178 N) Modified Test Method: If a test machine is not available (as in ASTM D 1682) or, if an existing machine is not calibrated for testing this material, the followi

9、ng manner of testing may be employed. Prepare samples per ASTM D 1682. Prepare a set of clamps, or holding devices, having the same width as the sample tested. A top clamp should be made to facilitate “pick-up“ and holding by the operator. A bottom clamp should be made with an attached hook on the b

10、ottom, or some means for adding and suspending required weights for test. The bottom clamp weight should be known so that the total accumulative suspended weight may be determined. Carefully clamp sample in holding devices. Add the required weight to the bottom clamp, then gently pick up the top cla

11、mp to allow a tensile pull on the sample. This may be repeated with additional weights to determine minimum breaking strength. 3.5 COMPRESSION AND RECOVERY 3.5.1 ESB-M12G64-A Compression, max 10% Recovery, min 95% 3.5.2 ESB-M12G65-A/ B Compression, max 5% Recovery, min 95% Test Method: Cut five 12 x

12、 12 in (305 x 305 mm) samples. (Thickness as specified on engineering drawings.) Apply a 12 x 12 in (305 x 305 mm) masonite board weighing 1/2 lb (0.23 kg) to the five plied samples. Measure the height of the pile, at the center of the vertical sides. (The average of these readings is the initial th

13、ickness of the pile (T1). ENGINEERING MATERIAL SPECIFICATION ESB-M12G64-A ESB-M12G65-A/B Copyright 2012, Ford Global Technologies, LLC Page 3 of 4 Apply a 5 lb (2.3 kg) load to the center of the pile and measure again for average thickness of the pile with load (T2). % Compression = T1 - T2 x 100 _

14、T1 Remove the load and allow pile (with board) to recover thickness for 30 min. Measure again for average thickness of the pile (T3). % Recovery = T3 x 100 _ T1 3.6 MOISTURE RESISTANCE Shall not disintegrate, delaminate, nor sustain mold growth. Test Method: Suspend a 12 x 12 x 1 in (305 x 305 x 25

15、mm) sample in a relative humidity cabinet at 38 +/- 1 C and 95 - 100% R.H. for 7 days. 3.7 AIR FLOW RESISTANCE No evidence of fiber separation nor delamination of the skin effect side. Test Method: Direct a blast of air at 45 to the center portion of a representative 1 ft2 (930 cm2) sample. Test in

16、one direction, then test at 45 in a direction opposed 90 to the first test. Height and Angle of Gun: Vertical height of gun tip shall be 3 in (76 mm) from mat surface and gun shall be held at an angle of 45. Equipment: Use a DeVilbiss JGA Type 502 spray gun with an AV-15FF Fluid Tip, JGA 402FF Needl

17、e without air cap, or equivalent. Time: 20 s minimum for each direction. Air pressure: 90 - 100 psi (0.6 - 0.7 MPa) ENGINEERING MATERIAL SPECIFICATION ESB-M12G64-A ESB-M12G65-A/B Copyright 2012, Ford Global Technologies, LLC Page 4 of 4 3.8 SOUND ABSORPTION, min (Based on 0.75 in (19.1 mm) thickness

18、) 50% Test Method: The average sound absorption, as tested by General Parts Division, General Products Office, shall exceed the above minimum value over a range of 500 - 5000 cps. 3.10 ESB-M12G65-B FLAMMABILITY REQUIREMENT 3.10.1 Flammability In order to comply with Federal Motor Vehicle Safety Stan

19、dard No. 302, the materials, portions of components, and composites shall not burn, or transmit a flame across its surface, at a rate of more than 4 in (101 mm) per min. To demonstrate compliance, the sample size and method of testing shall be in accordance with FLTM BN 024-02. 3.10.2 Performance -

20、Environmental Aging All materials, portions of components, and composites defined by this specification that have not been treated, modified or reformulated and exceed a max burn rate of 3.0 in (76 mm) per min as specified by the Flammability Lot Sampling Plan of FLTM BN 024-02, must be evaluated fo

21、r permanency of the materials flame retardant properties per ESB-M25P3-A according to the accelerated environmental aging requirements applicable to the basic material category of this particular specification. Any material, portions of components, and composites defined by this specification that h

22、ave been treated, modified or reformulated to conform to Flammability Lot Sampling Plan of FLTM BN 024-02, regardless of max burn rate, must be evaluated for both permanency of materials flame retardant properties and changes in mechanical, chemical and physical properties per ESB-M25P3-A applicable to the basic materials category of this particular specification. 3.10.3 Flammability Test Program Materials, portions of components, and composites governed by this specification must also comply with the requirements of ES-D3AB-11014-AA.