ETSI TS 125 116-2017 Universal Mobile Telecommunications System (UMTS) UTRA repeater radio transmission and reception (LCR TDD) (V14 0 0 3GPP TS 25 116 version 14 0 0 Release 14)《通.pdf

《ETSI TS 125 116-2017 Universal Mobile Telecommunications System (UMTS) UTRA repeater radio transmission and reception (LCR TDD) (V14 0 0 3GPP TS 25 116 version 14 0 0 Release 14)《通.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 125 116-2017 Universal Mobile Telecommunications System (UMTS) UTRA repeater radio transmission and reception (LCR TDD) (V14 0 0 3GPP TS 25 116 version 14 0 0 Release 14)《通.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 125 116 V14.0.0 (2017-04) Universal Mobile Telecommunications System (UMTS); UTRA repeater radio transmission and reception (LCR TDD) (3GPP TS 25.116 version 14.0.0 Release 14) TECHNICAL SPECIFICATION ETSI ETSI TS 125 116 V14.0.0 (2017-04)13GPP TS 25.116 version 14.0.0 Release 14Reference R

2、TS/TSGR-0425116ve00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present d

3、ocument can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In

4、 case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the do

5、cument may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:

6、/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be m

7、odified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benef

8、it of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 125 116

9、V14.0.0 (2017-04)23GPP TS 25.116 version 14.0.0 Release 14Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, a

10、nd can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to th

11、e ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. For

12、eword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the co

13、rresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “c

14、annot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 125 116 V14.0.0 (2017-04)33GPP TS 25.116 version 14.0.0 Rel

15、ease 14Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Definitions, symbols and abbreviations . 6g33.1 Definitions 6g33.2 Symbols 7g33.3 Abbreviations . 7g34 General . 7g34.1 Relationship between Minimum Requirements and Te

16、st Requirements 8g34.2 Regional requirements 9g35 Frequency bands and channel arrangement 10g35.1 General . 11g35.2 Frequency bands . 11g35.3 TX-RX frequency separation . 11g35.4 Channel arrangement 11g35.4.1 Channel spacing 11g35.4.2 Channel raster . 11g35.4.3 Channel number 11g36 Output power 12g3

17、6.1 Maximum output power . 12g36.1.1 Minimum Requirements . 12g37 Frequency stability . 12g37.1 Minimum requirement 12g38 Out of band gain . 12g38.1 Minimum requirement 13g39 Unwanted emission 13g39.1 Spectrum emission mask 13g39.2 Spurious emissions . 15g39.2.1 Mandatory Requirements 15g39.2.1.1 Sp

18、urious emissions (Category A) 15g39.2.1.1.1 Minimum Requirement . 15g39.2.1.2 Spurious emissions (Category B) 16g39.2.1.2.1 Minimum Requirement . 16g39.2.2 Co-existence with GSM 900 . 16g39.2.2.1 Operation in the same geographic area . 16g39.2.2.1.1 Minimum Requirement . 16g39.2.2.2 Co-located base

19、stations 16g39.2.2.2.1 Minimum Requirement . 17g39.2.3 Co-existence with DCS 1800 17g39.2.3.1 Operation in the same geographic area . 17g39.2.3.1.1 Minimum Requirement . 17g39.2.3.2 Co-located base stations 17g39.2.3.2.1 Minimum Requirement . 17g39.2.4 Co-existence with UTRA-FDD 18g39.2.4.1 Operatio

20、n in the same geographic area . 18g39.2.4.1.1 Minimum Requirement . 18g39.2.4.2 Co-located base stations 18g39.2.4.2.1 Minimum Requirement . 18g3ETSI ETSI TS 125 116 V14.0.0 (2017-04)43GPP TS 25.116 version 14.0.0 Release 149.2.5 Co-existence with unsynchronised TDD 19g39.2.5.1 Operation in the same

21、 geographic area . 19g39.2.5.1.1 Minimum Requirement . 19g39.2.5.2 Co-located base stations 19g39.2.5.2.1 Minimum Requirement . 20g310 Modulation accuracy 20g310.1 Error Vector Magnitude . 20g310.1.1 Minimum requirement 20g310.2 Peak code domain error 20g310.2.1 Minimum requirement 20g311 Input inte

22、rmodulation . 21g311.1 General requirement . 21g311.1.1 Minimum requirement 21g312 Output intermodulation 21g312.0 General . 21g312.1 Minimum requirement 21g313 Adjacent Channel Rejection Ratio (ACRR) . 22g313.1 Definitions and applicability 22g313.2 Co-existence with UTRA . 22g313.2.1. Minimum Requ

23、irements . 22g314 Timing Accuracy 22g314.1 Minimum requirement 22g3Annex A (normative): Environmental requirements for the Repeater equipment 24g3Annex B (informative): Change history . 25g3History 26g3ETSI ETSI TS 125 116 V14.0.0 (2017-04)53GPP TS 25.116 version 14.0.0 Release 14Foreword This Techn

24、ical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by

25、 the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incr

26、emented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 116 V14.0.0 (2017-04)63GPP TS 25.116 version 14.0.0 Release 141 Scope The present docume

27、nt establishes the minimum RF characteristics of LCR TDD Repeater. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version

28、number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that doc

29、ument in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 ITU-R Recommendation SM.329, “Unwanted emissions in the spurious domain“. 3 ITU-R Recommendation M.1545: “Measurement uncertainty as it applies to test limits for the terrestrial component of

30、 International Mobile Telecommunications-2000”. 4 3GPP TS 25.153: “LCR TDD Repeater conformance testing” 5 3GPP TR 25.942: “RF system scenarios“. 6 IEC 60721-3-3 (2002): “Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities -

31、Section 3: Stationary use at weather protected locations“. 7 IEC 60721-3-4 (1995): “Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 4: Stationary use at non-weather protected locations“. 3 Definitions, symbols a

32、nd abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TR 21.905 1 and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 1. Carrier: The modulated waveform con

33、veying the LCR TDD physical channels Channel bandwidth: The RF bandwidth supporting a single LCR TDD RF carrier with the transmission bandwidth configured in the uplink or downlink of a cell. The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF requirem

34、ents. Channel edge: The lowest and highest frequency of the LCR TDD carrier, separated by the channel bandwidth. Donor coupling loss: is the coupling loss between the repeater and the donor base station. Downlink: Signal path where base station transmits and mobile receives. ETSI ETSI TS 125 116 V14

35、.0.0 (2017-04)73GPP TS 25.116 version 14.0.0 Release 14Maximum output power, Pmax: This is the mean power level per carrier measured at the antenna connector of the Repeater in specified reference condition. Output power, Pout: This is the mean power of one carrier at maximum repeater gain delivered

36、 to a load with resistance equal to the nominal load impedance of the transmitter. Pass band: The repeater can have one or several pass bands. The pass band is the frequency range that the repeater operates in with operational configuration. This frequency range can correspond to one or several cons

37、ecutive nominal channels. If they are not consecutive each subset of channels shall be considered as an individual pass band. Rated output power: Rated output power of the repeater is the mean power level per carrier that the manufacturer has declared to be available at the antenna connector. Repeat

38、er: A device that receives, amplifies and transmits the radiated or conducted RF carrier both in the down-link direction (from the base station to the mobile area) and in the up-link direction (from the mobile to the base station) Transmission bandwidth: Bandwidth of an instantaneous transmission fr

39、om a UE or BS, measured in Resource Block units. Transmission bandwidth configuration: The highest transmission bandwidth allowed for uplink or downlink in a given channel bandwidth, measured in Resource Block units. Uplink: Signal path where mobile transmits and base station receives. 3.2 Symbols F

40、or the purposes of the present document, the following symbols apply: BWChannelChannel bandwidth BWConfigTransmission bandwidth configuration, expressed in MHz. BWMeasMeasurement bandwidth BWSignalBandwidth of the repeater input signal filling the repeater pass band FDL_low The lowest frequency of t

41、he downlink operating band FDL_high The highest frequency of the downlink operating band FUL_low The lowest frequency of the uplink operating band FUL_high The highest frequency of the uplink operating band f_offset_PB Distance from the channel edge frequency of the first or last channel in the pass

42、 band NDLDownlink LARFCN NOffs-DLOffset used for calculating downlink LARFCN NOffs-ULOffset used for calculating uplink LARFCN NRBTransmission bandwidth configuration, expressed in units of resource blocks NULUplink LARFCN Pmax Maximum output power Pout Output power 3.3 Abbreviations For the purpose

43、s of the present document, the abbreviations given in TR 21.905 1 and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905 1. ACRR Adjacent Channel Rejection Ratio BS Base Station LARFCN LCR TDD Absol

44、ute Radio Frequency Channel Number PB Pass Band 4 General This specification applies only to LCR TDD repeaters. Unless otherwise stated, all requirements in this specification apply to both the up-link and down-link directions. ETSI ETSI TS 125 116 V14.0.0 (2017-04)83GPP TS 25.116 version 14.0.0 Rel

45、ease 144.1 Relationship between Minimum Requirements and Test Requirements The Minimum Requirements given in this specification make no allowance for measurement uncertainty. The test specification TS 25.153 section 4 defines Test Tolerances. These Test Tolerances are individually calculated for eac

46、h test. The Test Tolerances are used to relax the Minimum Requirements in this specification to create Test Requirements. The measurement results returned by the Test System are compared - without any modification - against the Test Requirements as defined by the shared risk principle. The Shared Ri

47、sk principle is defined in ITU-R M.1545 3. ETSI ETSI TS 125 116 V14.0.0 (2017-04)93GPP TS 25.116 version 14.0.0 Release 144.2 Regional requirements Some requirements in the present document may only apply in certain regions. Table 4.2-1 lists all requirements that may be applied differently in diffe

48、rent regions. Table 4.2-1: List of regional requirements ETSI ETSI TS 125 116 V14.0.0 (2017-04)103GPP TS 25.116 version 14.0.0 Release 14Clause number Requirement Comments 5.2 Channel bandwidth Some channel bandwidths may be applied regionally. 5.3 Frequency bands Some bands may be applied regionall

49、y. 5.4 Channel arrangement The requirement is applied according to what frequency bands in Clause 5.3 that are supported by the Repeater. 6.1 Maximum output power In certain regions, the minimum requirement for normal conditions may apply also for some conditions outside the range of conditions defined as normal. 9.1.1.1 Operating band unwanted emissions (Category A) This requirement is mandatory for regions where Category A limits for spurious emissions, as defined in ITU-R Recommendation SM.329 2 apply. 9.1.1.2 Operating band unwanted emissio