ETSI 3GPP TS 25 104-2003 See TS 125 104 V6 1 0 (Version 6 1 0 Release 6).pdf

《ETSI 3GPP TS 25 104-2003 See TS 125 104 V6 1 0 (Version 6 1 0 Release 6).pdf》由会员分享，可在线阅读，更多相关《ETSI 3GPP TS 25 104-2003 See TS 125 104 V6 1 0 (Version 6 1 0 Release 6).pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 125 104 V6.1.0 (2003-03)Technical Specification Universal Mobile Telecommunications System (UMTS);UTRA (BS) FDD;Radio transmission and reception(3GPP TS 25.104 version 6.1.0 Release 6)ETSI ETSI TS 125 104 V6.1.0 (2003-03) 1 3GPP TS 25.104 version 6.1.0 Release 6 Reference RTS/TSGR-0425104v6

2、10 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the prese

3、nt document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case o

4、f dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and o

5、ther ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction ext

6、end to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefi

7、t of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 125 104 V6.1.0 (2003-03) 2 3GPP TS 25.104 version 6.1.0 Release 6 Intellectual Property Rights IPRs essential or potentially essential to the present docum

8、ent may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of

9、ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existe

10、nce of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may

11、 refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.o

12、rg/key/queryform.asp . ETSI ETSI TS 125 104 V6.1.0 (2003-03) 3 3GPP TS 25.104 version 6.1.0 Release 6 Contents Intellectual Property Rights2 Foreword.2 Foreword.6 1 Scope 7 2 References 7 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .8 4 General .8 4.1 Relationship between Mi

13、nimum Requirements and Test Requirements8 4.2 Base station classes 9 4.3 Regional requirements10 4.4 Environmental requirements for the BS equipment .11 5 Frequency bands and channel arrangement12 5.1 General .12 5.2 Frequency bands.12 5.3 Tx-Rx frequency separation .12 5.4 Channel arrangement12 5.4

14、.1 Channel spacing12 5.4.2 Channel raster .12 5.4.3 Channel number13 6 Transmitter characteristics .13 6.1 General .13 6.2 Base station output power 13 6.2.1 Base station maximum output power14 6.2.1.1 Minimum requirement 14 6.3 Frequency error 14 6.3.1 Minimum requirement 14 6.4 Output power dynami

15、cs14 6.4.1 Inner loop power control in the downlink.14 6.4.1.1 Power control steps .14 6.4.1.1.1 Minimum requirement.15 6.4.2 Power control dynamic range .15 6.4.2.1 Minimum requirements.15 6.4.3 Total power dynamic range 15 6.4.3.1 Minimum requirement 15 6.4.4 Primary CPICH power15 6.4.4.1 Requirem

16、ent 16 6.4.5 IPDL time mask16 6.4.5.1 Minimum Requirement .16 6.5 (void)16 6.6 Output RF spectrum emissions.16 6.6.1 Occupied bandwidth .16 6.6.2 Out of band emission 16 6.6.2.1 Spectrum emission mask.17 6.6.2.2 Adjacent Channel Leakage power Ratio (ACLR).19 6.6.2.2.1 Minimum requirement.19 6.6.3 Sp

17、urious emissions .19 6.6.3.1 Mandatory Requirements 19 6.6.3.1.1 Spurious emissions (Category A) 19 6.6.3.1.2 Spurious emissions (Category B) 20 6.6.3.2 Protection of the BS receiver of own or different BS .22 ETSI ETSI TS 125 104 V6.1.0 (2003-03) 4 3GPP TS 25.104 version 6.1.0 Release 6 6.6.3.2.1 M

18、inimum Requirement .22 6.6.3.3 Co-existence with GSM 900 .22 6.6.3.3.1 Operation in the same geographic area22 6.6.3.3.2 Co-located base stations 23 6.6.3.4 Co-existence with DCS 1800 23 6.6.3.4.1 Operation in the same geographic area23 6.6.3.4.2 Co-located base stations 23 6.6.3.5 Co-existence with

19、 PHS .24 6.6.3.5.1 Minimum Requirement .24 6.6.3.6 Co-existence with services in adjacent frequency bands.24 6.6.3.6.1 Minimum requirement.24 6.6.3.7 Co-existence with UTRA-TDD 24 6.6.3.7.1 Operation in the same geographic area24 6.6.3.7.2 Co-located base stations 25 6.6.3.8 Co-existence with UTRA i

20、n frequency band I25 6.6.3.8.1 Operation in the same geographic area25 6.6.3.8.2 Co-located base stations 25 6.6.3.9 Co-existence with UTRA in frequency band III .26 6.6.3.9.1 Operation in the same geographic area26 6.6.3.9.2 Co-located base stations 26 6.6.3.10 Co-existence with PCS190026 6.6.3.10.

21、1 Operation in the same geographic area26 6.6.3.10.2 Co-located base stations 27 6.6.3.11 Co-existence with GSM850 27 6.6.3.11.1 Operation in the same geographic area27 6.6.3.11.2 Co-located base stations 27 6.7 Transmit intermodulation .28 6.7.1 Minimum requirement 28 6.8 Transmit modulation 28 6.8

22、.1 Transmit pulse shape filter28 6.8.2 Error Vector Magnitude29 6.8.2.1 Minimum requirement 29 6.8.3 Peak code Domain error .29 6.8.3.1 Minimum requirement 29 6.8.4 Time alignment error in Tx Diversity.29 6.8.4.1 Minimum Requirement .29 7 Receiver characteristics29 7.1 General .29 7.2 Reference sens

23、itivity level30 7.2.1 Minimum requirement 30 7.2.2 Maximum Frequency Deviation for Receiver Performance .30 7.3 Dynamic range .30 7.3.1 Minimum requirement 30 7.4 Adjacent Channel Selectivity (ACS)31 7.4.1 Minimum requirement 31 7.4.2 Minimum requirement Co-location with UTRA-TDD 31 7.5 Blocking cha

24、racteristics .31 7.5.1 Minimum requirement 32 7.5.2 Minimum Requirement Co-location with GSM900, DCS 1800, PCS1900, GSM850 and/or UTRA .33 7.5.3 Minimum Requirement - Co-location with UTRA-TDD .34 7.6 Intermodulation characteristics 34 7.6.1 Minimum requirement 35 7.7 Spurious emissions.36 7.7.1 Min

25、imum requirement 36 8 Performance requirement .37 8.1 General .37 8.2 Demodulation in static propagation conditions 37 8.2.1 Demodulation of DCH37 8.2.1.1 Minimum requirement 37 8.3 Demodulation of DCH in multipath fading conditions 38 ETSI ETSI TS 125 104 V6.1.0 (2003-03) 5 3GPP TS 25.104 version 6

26、.1.0 Release 6 8.3.1 Multipath fading Case 138 8.3.1.1 Minimum requirement 38 8.3.2 Multipath fading Case 238 8.3.2.1 Minimum requirement 39 8.3.3 Multipath fading Case 339 8.3.3.1 Minimum requirement 39 8.3.4 Multipath fading Case 439 8.3.4.1 Minimum requirement 40 8.4 Demodulation of DCH in moving

27、 propagation conditions.40 8.4.1 Minimum requirement 40 8.5 Demodulation of DCH in birth/death propagation conditions40 8.5.1 Minimum requirement 40 8.6 void.41 8.7 Performance requirement for RACH41 8.7.1 Performance requirement for RACH preamble detection.41 8.7.2 Demodulation of RACH message.41 8

28、.7.2.1 Minimum requirements for Static Propagation Condition 41 8.7.2.2 Minimum requirements for Multipath Fading Case 3.41 8.8 Performance requirement for CPCH 42 8.8.1 Performance requirement for CPCH preamble detection .42 8.8.1.1 Detection of CPCH Access Preamble (AP) 42 8.8.1.2 Detection of CPC

29、H Collision Detection Preamble (CD) 42 8.8.2 Demodulation of CPCH message part 42 8.8.2.1 Minimum requirements for Static Propagation Condition 42 8.8.2.2 Minimum requirements for Multipath Fading Case 3.42 8.9 BS Functionality in Site Selection Diversity Transmission (SSDT) Mode42 8.9.1 Minimum req

30、uirements.43 Annex A (normative): Measurement channels44 A.1 Summary of UL reference measurement channels.44 A.2 UL reference measurement channel for 12.2 kbps.45 A.3 UL reference measurement channel for 64 kbps46 A.4 UL reference measurement channel for 144 kbps47 A.5 UL reference measurement chann

31、el for 384 kbps48 A.6 UL reference measurement channel for 2048 kbps49 A.7 Reference measurement channels for UL RACH 50 Annex B (normative): Propagation conditions51 B.1 Static propagation condition.51 B.2 Multi-path fading propagation conditions51 B.3 Moving propagation conditions51 B.4 Birth-Deat

32、h propagation conditions .52 Annex C (normative): Characteristics of the W-CDMA interference signal53 Annex D (informative): Change history .54 History 59 ETSI ETSI TS 125 104 V6.1.0 (2003-03) 6 3GPP TS 25.104 version 6.1.0 Release 6 Foreword This Technical Specification has been produced by the 3GP

33、P. The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of this TS, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows

34、: Version 3.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 Indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third d

35、igit is incremented when editorial only changes have been incorporated in the specification. ETSI ETSI TS 125 104 V6.1.0 (2003-03) 7 3GPP TS 25.104 version 6.1.0 Release 6 1 Scope This document establishes the Base Station minimum RF characteristics of the FDD mode of UTRA. 2 References The followin

36、g documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply.

37、For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 ITU-R Recommendation SM.329-9, “Spuriou

38、s emissions“. 2 (void) 3 ETSI ETR 273-1-2: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement of radiated methods of measurement (using test sites) and evaluation of the corresponding measurement uncertainties; Part 1: Uncertainties in the measurement of mobile radio equipm

39、ent characteristics; Sub-part 2: Examples and annexes“. 4 3GPP TR 25.942 “RF System Scenarios“. 5 3GPP TS 45.004: “Digital cellular telecommunications system (Phase 2+); Modulation”. 6 3GPP TS 25.213: “Spreading and modulation (FDD)“. 3 Definitions and abbreviations 3.1 Definitions For the purposes

40、of the present document, the following definitions apply: Output power: The mean power of one carrier of the base station, delivered to a load with resistance equal to the nominal load impedance of the transmitter. Rated output power: Rated output power of the base station is the mean power level pe

41、r carrier that the manufacturer has declared to be available at the antenna connector. Maximum output Power: The mean power level per carrier of the base station measured at the antenna connector in a specified reference condition. Mean power: When applied to a W-CDMA modulated signal this is the po

42、wer (transmitted or received) in a bandwidth of at least (1+ ) times the chip rate of the radio access mode. The period of measurement shall be at least one timeslot unless otherwise stated. Power control dynamic range: The difference between the maximum and the minimum transmit output power of a co

43、de channel for a specified reference condition. RRC filtered mean power: The mean power as measured through a root raised cosine filter with roll-off factor and a bandwidth equal to the chip rate of the radio access mode. ETSI ETSI TS 125 104 V6.1.0 (2003-03) 8 3GPP TS 25.104 version 6.1.0 Release 6

44、 NOTE 1: The RRC filtered mean power of a perfectly modulated W-CDMA signal is 0.246 dB lower than the mean power of the same signal. Code domain power: That part of the mean power which correlates with a particular (OVSF) code channel. The sum of all powers in the code domain equals the mean power

45、in a bandwidth of (1+ ) times the chip rate of the radio access mode. Total power dynamic range: The difference between the maximum and the minimum total transmit output power for a specified reference condition. NOTE 2: The roll-off factor is defined in section 6.8.1. Node B Tx Diversity mode - A N

46、ode B is in transmit diversity mode when the CPICH transmit diversity indicator, P-CCPCH STTD indicator and the primary and secondary SCH TSTD indicators are enabled. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: 16QAM 16 Quadrature Amplitude Modulati

47、on ACIR Adjacent Channel Interference Ratio ACLR Adjacent Channel Leakage power Ratio ACS Adjacent Channel Selectivity BS Base Station BER Bit Error Ratio BLER Block Error Ratio CW Continuous Wave (unmodulated signal) DL Down Link (forward link) FDD Frequency Division Duplexing GSM Global System for

48、 Mobile Communications PoutOutput Power PRATRated Output Power PHS Personal Handyphone System PPM Parts Per Million QPSK Quadrature Phase Shift Keying RSSI Received Signal Strength Indicator SIR Signal to Interference ratio TDD Time Division Duplexing TPC Transmit Power Control UARFCN UTRA Absolute

49、Radio Frequency Channel Number UE User Equipment UL Up Link (reverse link) WCDMA Wideband Code Division Multiple Access 4 General 4.1 Relationship between Minimum Requirements and Test Requirements The Minimum Requirements given in this specification make no allowance for measurement uncertainty. The test specification 25.141 section 4 defines Test Tolerances. These Test Tolerances are individually calculated for each test. The Test Tolerances are used to relax the Minimum Requirements in this specification to create Test Requirements. The measuremen