EN ISO 18752-2016 en Rubber hoses and hose assemblies - Wire- or textilereinforced single-pressure types for hydraulic applications - Specification《橡胶软管和软管组件线或织物增强单压型液压系统规范(ISO 187.pdf

《EN ISO 18752-2016 en Rubber hoses and hose assemblies - Wire- or textilereinforced single-pressure types for hydraulic applications - Specification《橡胶软管和软管组件线或织物增强单压型液压系统规范(ISO 187.pdf》由会员分享，可在线阅读，更多相关《EN ISO 18752-2016 en Rubber hoses and hose assemblies - Wire- or textilereinforced single-pressure types for hydraulic applications - Specification《橡胶软管和软管组件线或织物增强单压型液压系统规范(ISO 187.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 18752:2016Rubber hoses and hoseassemblies Wire- or textile-reinforced single-pressuretypes for hydraulic applications Specification (ISO 18752:2014)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 18752:2016 BRITISH STANDARDNational forewordThe UK

2、participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions

3、of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. ISBN 978 0 580 91775 2ICS 23.040.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy a

4、nd Strategy Committee on 31 March 2014.Amendments/corrigenda issued since publicationDate Text affected31 August 2016 This corrigendum renumbers BS ISO 18752:2014 asBS EN ISO 18752:2016This British Standard is the UK implementation of EN ISO 18752:2016. It is identical to ISO 18752:2014. It supersed

5、es BS ISO 18752:2014 which is withdrawn.Published by BSI Standards Limited 2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 18752 July 2016 ICS 23.040.70 English Version Rubber hoses and hose assemblies - Wire- or textile-reinforced single-pressure types for hydraulic applications - Spec

6、ification (ISO 18752:2014) Tuyaux et flexibles en caoutchouc - Types hydrauliques avec armature de fils mtalliques tresss - Spcifications (ISO 18752:2014) Gummischluche und -schlauchleitungen - Draht- oder textilverstrkte Einzeldrucktypen fr hydraulische Anwendungen - Anforderungen (ISO 18752:2014)

7、This European Standard was approved by CEN on 12 June 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere

8、nces concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN

9、member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

10、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHE

11、S KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 18752:2016 E3 European foreword The text of ISO 18752:2014 has been prepared by Technica

12、l Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 18752:2016 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by DIN. This European Standar

13、d shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2017, and conflicting national standards shall be withdrawn at the latest by January 2017. Attention is drawn to the possibility that some of the elements of thi

14、s document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stan

15、dard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Sp

16、ain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 18752:2014 has been approved by CEN as EN ISO 18752:2016 without any modification. BS EN ISO 18752:2016EN ISO 18752:2016 (E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative refe

17、rences 13 Terms and definitions . 24 Classification 24.1 Classes 24.2 Grades and types . 25 Materials and construction . 35.1 Hoses . 35.2 Hose assemblies . 36 Dimensions and tolerances . 46.1 Diameters 46.2 Cover thickness . 66.3 Concentricity. 67 Physical properties 77.1 Fluid resistance of rubber

18、 compounds 77.2 Performance requirements 78 Frequency of testing .109 Marking .109.1 Hoses 109.2 Hose assemblies 1010 Recommendations for packaging and storage .1111 Test report 11Annex A (normative) Type tests and routine tests .12Annex B (informative) Production acceptance tests .13Annex C (inform

19、ative) Recommendations for tolerances on lengths of hose assemblies .14Annex D (informative) Information to be provided by hose manufacturer 15Bibliography .16BS EN ISO 18752:2016ISO 18752:2014 (E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national

20、standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International

21、 organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for

22、 its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org

23、/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be i

24、n the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions re

25、lated to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC

26、1, Hoses (rubber and plastics).This third edition cancels and replaces the second edition (ISO 18752:2012), of which it constitutes a minor revision, to include data of “Class 490” in Table 7.iv ISO 2014 All rights reservedBS EN ISO 18752:2016ISO 18752:2014 (E)INTERNATIONAL STANDARD Rubber hoses and

27、 hose assemblies Wire- or textile-reinforced single-pressure types for hydraulic applications Specification1 ScopeThis International Standard specifies requirements for ten classes, four grades and seven types of wire- or textile-reinforced hydraulic hoses and hose assemblies of nominal sizes rangin

28、g from 5 to 102. Each class has a single maximum working pressure for all sizes. Such hoses are suitable for use with hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from 40 C to +100 C for types AS, AC, BS and BC and 40 C to +120 C for types CS, CC and DC.Thi

29、s International Standard does not include requirements for the connection ends. It is limited to the performance of hoses and hose assemblies. The hose assembly maximum working pressure is governed by the lowest maximum working pressure of the components.NOTE It is the responsibility of the user, in

30、 consultation with the hose manufacturer, to establish the compatibility of the hose with the fluid to be used.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references

31、, the latest edition of the referenced document (including any amendments) applies.ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1817, Rubber, vulcanized or thermoplastic Determination of the effect of liquidsISO 4671, Rubber and plastics hoses and hose assemblies Me

32、thods of measurement of the dimensions of hoses and the lengths of hose assembliesISO 6803, Rubber or plastics hoses and hose assemblies Hydraulic-pressure impulse test without flexingISO 7233, Rubber and plastics hoses and hose assemblies Determination of resistance to vacuumISO 7326:2006, Rubber a

33、nd plastics hoses Assessment of ozone resistance under static conditionsISO 8033:2006, Rubber and plastics hoses Determination of adhesion between componentsISO 8330, Rubber and plastics hoses and hose assemblies VocabularyISO 8331, Rubber and plastics hoses and hose assemblies Guidelines for select

34、ion, storage, use and maintenanceISO 10619-1, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperatureISO 10619-2:2011, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 2: Bending tests at sub-ambient

35、 temperaturesISO 17165-1, Hydraulic fluid power Hose assemblies Part 1: Dimensions and requirements ISO 2014 All rights reserved 1BS EN ISO 18752:2016 ISO 18752:2014 (E)3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8330 apply.4 Classification4.1 Cla

36、ssesTen classes of hose are specified, distinguished by their maximum working pressure, as shown in Table 1. Each class may be manufactured in up to 14 nominal sizes.Table 1 Classes and nominal sizesClass 35 70 140 210 250 280 350 420 490 560MWPa(MPa) 3,5 7 14 21 25 28 35 42 49 56MWPa(bar) 35 70 140

37、 210 250 280 350 420 490 560Nominal size5 X X X X X X X X N/A N/A6,3 X X X X X X X X N/A N/A8 X X X X X X X X N/A N/A10 X X X X X X X X N/A N/A12,5 X X X X X X X X N/A N/A16 X X X X X X X X X X19 X X X X X X X X X X25 X X X X X X X X X X31,5 X X X X X X X X X X38 X X X X X X X X N/A N/A51 X X X X X

38、X X X N/A N/A63 X X X X X X X N/A N/A N/A76 X X X N/A N/A N/A N/A N/A N/A N/A102 X N/A N/A N/A N/A N/A N/A N/A N/A N/ANOTE X = Applicable; N/A = Not applicable.aMaximum working pressure.4.2 Grades and typesHoses are classified into four gradesaccording to their resistance to impulse: A, B, C and D.

39、Each grade is classified by outside diameter into standard types (AS, BS and CS) and compact types (AC, BC, CC and DC), as shown in Table 2.2 ISO 2014 All rights reservedBS EN ISO 18752:2016 ISO 18752:2014 (E)Table 2 Grades and typesGrade TypeaResistance to impulseTemperature CImpulse pressure (% of

40、 MWPb)Minimum number of cyclesAAS100 133 % 200 000ACBBS100 133 % 500 000BCCCS120 133 % and 120 %c500 000CCD DC 120 133 % 1 000 000aStandard or compact, e.g. CS is grade C and standard type.As shown in Table 4 and Table 8, standard types have larger outside diameters and larger bend radii and compact

41、 types have smaller outside diameters and smaller bend radii.bMaximum working pressure.c120 % of the MWP shall be used for classes 350, 420, 490 and 560 instead of 133 %.Each class includes one of each type or both as shown in Table 3.Table 3 Type and maximum working pressureClass 35 70 140 210 250

42、280 350 420 490 560MWPa(MPa) 3,5 7 14 21 25 28 35 42 49 56MWPa(bar) 35 70 140 210 250 280 350 420 490 560Grade TypeAAS X X X X X X X X N/A N/AAC X X X X X X X X N/A N/ABBS X X X X X X X X N/A N/ABC X X X X X X X X N/A N/ACCS N/A N/A N/A X X X X X N/A N/ACC N/A N/A N/A X X X X X X XD DC N/A N/A N/A X

43、 X X X X N/A N/ANOTE X = Applicable; N/A = Not applicable.aMaximum working pressure.5 Materials and construction5.1 HosesHoses shall consist of a hydraulic-fluid-resistant rubber lining, one or multiple layers of steel wire or textile and an oil-, abrasion- and weather-resistant rubber cover. A laye

44、r of other materials on the rubber cover is allowed for improved resistance to abrasion or other.5.2 Hose assembliesHose assemblies shall only be manufactured using hose fittings which conform to the requirements of 7.2.1, 7.2.4 and 7.2.5. ISO 2014 All rights reserved 3BS EN ISO 18752:2016 ISO 18752

45、:2014 (E)Follow the manufacturers instructions for the proper preparation and fabrication of hose assemblies.6 Dimensions and tolerances6.1 DiametersWhen measured in accordance with ISO 4671, the diameters of hoses shall conform to the values given in Table 4.4 ISO 2014 All rights reservedBS EN ISO

46、18752:2016 ISO 18752:2014 (E)Table4 Diameters of hosesNom-inalsizeInside diameter(allclasses)MaximumoutsidediameterofhosemmmmClass35Class70Class140Class210Class250Class280Class350Class420Class490Class560min.max.Stan-dardCom-pactStan-dardCom-pactStan-dardCom-pactStan-dardCom-pactStan-dardCom-pactStan

47、-dardCom-pactStan-dardCom-pactStan-dardCom-pactStan-dardCom-pactStan-dardCom-pact56,381012,516 192531,5385163 761024,66,17,79,312,315,518,625,031,437,750,463,174,6100,05,47,08,510,113,516,719,826,433,039,352,065,177,8103,21417 1921 2427 314053 59728410013011 1415 17 21 25 28 36 45 56 69 1417 1921 24

48、27 314053 59728410011 1415 182225 29 3845 56 69 1417 1921 2429 33 41 54 59738410011 1415 17 2225 29 384956 70 1417 19232629 33 41 53 597285 11 1416 19222631394956 70 17 1920232629 3441 54 597390 15 15 16 192227 32 394956 70 17 1920232629 3441 54 597390 15 15 16 192327 32 394956 70 17 19202327 29 385

49、0 54 6075 90 15 15 16 21 25 28 36 45 525973 17 19202427 37 50 54 6075 80 15 15 1822243446 50 56 7277 30 36 45 52 30 36 45 52 ISO 2014 All rights reserved 5BS EN ISO 18752:2016 ISO 18752:2014 (E)6.2 Cover thicknessWhen measured in accordance with ISO 4671, the outer cover thickness of hoses shall conform to the values given in Table 5. Standard types may