EN ISO 14122-3-2016 en Safety of machinery - Permanent means of access to machinery - Part 3 Stairs stepladders and guard-rails《机械安全-固定方式进入机器和工业设备的 -第3部分 楼梯 阶梯和护栏》.pdf

《EN ISO 14122-3-2016 en Safety of machinery - Permanent means of access to machinery - Part 3 Stairs stepladders and guard-rails《机械安全-固定方式进入机器和工业设备的 -第3部分 楼梯 阶梯和护栏》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 14122-3-2016 en Safety of machinery - Permanent means of access to machinery - Part 3 Stairs stepladders and guard-rails《机械安全-固定方式进入机器和工业设备的 -第3部分 楼梯 阶梯和护栏》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO 14122-3:2016Safety of machinery Permanent means of access tomachineryPart 3: Stairs, stepladders and guard-rails(ISO 14122-3:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 14122-3:2016 BRITISH STANDARDNational forewordThis British Standard i

2、s the UK implementation of EN ISO 14122-3:2016. It supersedes BS EN ISO14122-3:2001+A1:2010 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/208/1, Stairs and walkways - Industrial stairs.A list of organizations represented on this committee can be ob

3、tained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 84645 8 ICS 13.110 Compliance wi

4、th a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROP

5、ISCHE NORM EN ISO 14122-3 June 2016 ICS 13.110 Supersedes EN ISO 14122-3:2001English Version Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) Scurit des machines - Moyens daccs permanents aux machines - Partie 3: Escaliers,

6、 chelles marches et garde-corps (ISO 14122-3:2016) Sicherheit von Maschinen - Ortsfeste Zugnge zu maschinellen Anlagen - Teil 3: Treppen, Treppenleitern und Gelnder (ISO 14122-3:2016) This European Standard was approved by CEN on 29 April 2016. CEN members are bound to comply with the CEN/CENELEC In

7、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to a

8、ny CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official

9、versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw

10、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploi

11、tation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14122-3:2016 EBS EN ISO 14122-3:2016EN ISO 14122-3:2016 (E) 3 European foreword This document (EN ISO 14122-3:2016) has been prepared by Technical Committee ISO/TC 199 “Safety of machinery” in collaborat

12、ion with Technical Committee CEN/TC 114 “Safety of machinery” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2016, and conflicting national stand

13、ards shall be withdrawn at the latest by December 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN IS

14、O 14122-3:2001. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this

15、document. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, F

16、rance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 14122-3:2016 has been approved by CEN as E

17、N ISO 14122-3:2016 without any modification. BS EN ISO 14122-3:2016EN ISO 14122-3:2016 (E) 4 Annex ZA (informative) Relationship between this European Standard and the essential requirements of Directive 2006/42/EC machinery, and amending Directive 95/16/EC (recast) 2006 L157 aimed to be covered Thi

18、s European Standard has been prepared under a Commissions standardization request M/396 to provide one voluntary means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast) 2

19、006 L157. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding essential

20、requirements of that Directive, and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Directive 2006/42/EC 2006 L157 Essential Requirements of Directive 2006/42/EC Clause(s) / subclause(s) of this EN Remarks / Notes 1.5.15 “Risks of slipping, tripping or falli

21、ng” All 1.6.2 “Access to operating position and service points” All WARNING 1 Presumption of conformity stays valid only as long as a reference to this European Standard is maintained in the list published in the Official Journal of the European Union. Users of this standard should consult frequentl

22、y the latest list published in the Official Journal of the European Union. WARNING 2 Other Union legislation may be applicable to the product(s) falling within the scope of this standard. IMPORTANT: Compliance with the requirements of EN ISO 14122-1 and a relevant access-specific part of EN ISO 1412

23、2 is necessary to achieve presumption of conformity. BS EN ISO 14122-3:2016ISO 14122-3:2016(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 General requirements . 64.1 Construction and materials 64.2 Design and construction for the structure and the steps .

24、 65 Specific requirements applicable to stairs 66 Specific requirements applicable to step ladders 77 Specific requirements applicable to guard-rails . 97.1 Guard-rails for platforms, walkways and stair landings . 97.2 Guard-rails and handrails for stairs and handrails for step ladders 117.3 Additio

25、nal fall-protection when steps, stairs or ladders are near guard-rails of working platforms 137.4 Gates 138 Verification of safety requirements .148.1 General 148.2 Testing of guard-rails 148.2.2 Testing procedure 168.3 Testing of steps of a stair . 178.4 Testing of stepladders 19Annex A (informativ

26、e) Significant technical changes between this part of ISO 14122 and the previous edition .20Bibliography .22 ISO 2016 All rights reserved iiiContents PageBS EN ISO 14122-3:2016ISO 14122-3:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national st

27、andards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International o

28、rganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for i

29、ts further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/d

30、irectives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in

31、the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions rela

32、ted to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this document is ISO/TC 199, Safety of machinery.This second edition canc

33、els and replaces the first edition (ISO 14122-3:2001) which has been technically revised. It also incorporates the Amendment ISO 14122-3:2001/Amd 1:2010.ISO 14122 consists of the following parts, under the general title Safety of machinery Permanent means of access to machinery: Part 1: Choice of fi

34、xed means and general requirements of access Part 2: Working platforms and walkways Part 3: Stairs, stepladders and guard-rails Part 4: Fixed laddersAn additional part, dealing with mobile machinery, is under preparation.iv ISO 2016 All rights reservedBS EN ISO 14122-3:2016ISO 14122-3:2016(E)Introdu

35、ctionThis International Standard is a type-B standard as stated in ISO 12100. It is relevant, in particular, for the following stakeholder groups representing the market players with regard to machinery safety: machine manufacturers (small, medium and large enterprises); health and safety bodies (re

36、gulators, accident prevention organizations, market surveillance, etc.).Others can be affected by the level of machinery safety achieved with the means of this International Standard by the above-mentioned stakeholder groups: machine users/employers (small, medium and large enterprises); machine use

37、rs/employees (e.g. trade unions, organizations for peoples with special needs); service providers, e.g. for maintenance (small, medium and large enterprises); consumers (in case of machinery intended for use by consumers).The above-mentioned stakeholder groups have been given the possibility to part

38、icipate at the drafting process of this International Standard.In addition, this International Standard is intended for standardization bodies elaborating type-C standards. The requirements of this International Standard can be supplemented or modified by a type-C standard.For machines which are cov

39、ered by the scope of a type-C standard and which have been designed and built according to the requirements of that standard, the requirements of that type-C standard take precedence.The purpose of this International Standard is to define the general requirements for safe access to machines. ISO 141

40、22-1 gives guidance about the correct choice of access means when the necessary access to the machine is not possible directly from the ground level or from a floor or platform.The dimensions specified are consistent with established ergonomic data given in ISO 15534-3. ISO 2016 All rights reserved

41、vBS EN ISO 14122-3:2016BS EN ISO 14122-3:2016Safety of machinery Permanent means of access to machinery Part 3: Stairs, stepladders and guard-rails1 ScopeThis part of ISO 14122 gives requirements for non-powered stairs, stepladders and guard-rails which are a part of a stationary machine, and to the

42、 non-powered adjustable parts (e.g. foldable, slidable) and movable parts of those fixed means of access.NOTE 1 “Fixed” means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools.This part of ISO 14122 specifies minimu

43、m requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. stairs, stepladders, guard-rails) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to t

44、he machine.NOTE 2 Where no local regulation or standards exists, this part of ISO 14122 may be used also for means of access which are outside the scope of the standard.It is intended that this part of ISO 14122 be used with ISO 14122-1 to give the requirements for steps, stepladders and guard-rails

45、.The ISO 14122 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels.This part of ISO 14122 i

46、s not applicable to machinery manufactured before the date of its publication.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated r

47、eferences, the latest edition of the referenced document (including any amendments) applies.ISO 12100, Safety of machinery General principles for design Risk assessment and risk reductionISO 14122-1:2016, Safety of machinery Permanent means of access to machinery Part 1: Choice of fixed means and ge

48、neral requirements of access3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 12100, ISO 14122-1 and the following apply.INTERNATIONAL STANDARD ISO 14122-3:2016(E) ISO 2016 All rights reserved 1BS EN ISO 14122-3:2016ISO 14122-3:2016(E)3.1stairsstep ladd

49、erssuccession of horizontal levels steps (3.1.11) and landings (3.1.5) allowing passage on foot from one level to anotherNote 1 to entry: Stairs/step ladders are composed of the elements shown in Figure 1 and defined in 3.1.1 to 3.1.16.Note 2 to entry: For details on the angle of pitch (3.1.9) for stairs/step ladders, see ISO 14122-1:2016, 3.2 and 3.3.KeyH climbing height angle of pitchg going w widthe head-height p pitch lineh rise t depth of stepr overlap c clearanceFigure 1 Parts of stairs3.1.1climbing height