EN ISO 9100-5-2005 en Glass containers - Vacuum lug finishes - Part 5 43 and 48 regular《玻璃容器 真空凸缘瓶口 第5部分 普通规格43 和48 ISO 9100-5-2005》.pdf

《EN ISO 9100-5-2005 en Glass containers - Vacuum lug finishes - Part 5 43 and 48 regular《玻璃容器 真空凸缘瓶口 第5部分 普通规格43 和48 ISO 9100-5-2005》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 9100-5-2005 en Glass containers - Vacuum lug finishes - Part 5 43 and 48 regular《玻璃容器 真空凸缘瓶口 第5部分 普通规格43 和48 ISO 9100-5-2005》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 9100-5:2005 Glass containers Vacuum lug finishes Part 5: 43 and 48 regular The European Standard EN ISO 9100-5:2005 has the status of a British Standard ICS 55.100 BS EN ISO 9100-5:2005 This British Standard was published under the authority of the Standards Policy and Str

2、ategy Committee on 11 February 2005 BSI 11 February 2005 ISBN 0 580 45434 7 National foreword This British Standard is the official English language version of EN ISO 9100-5:2005. It is identical with ISO 9100-5:2005. The UK participation in its preparation was entrusted to Technical Committee PKW/0

3、, Packaging, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogu

4、e under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correc

5、t application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests infor

6、med; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document i

7、ndicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO91005 January2005 ICS55.100 Englishversion GlasscontainersVacuumlugfinishesPart5:43and48 regular(ISO91005:2005) RcipientsenverreBaguescranspourbou

8、chagesous videPartie5:43et48regular(ISO91005:2005) GlasbehlterVakuumNockenverschlussMndungen Teil5:43und48regular(ISO91005:2005) ThisEuropeanStandardwasapprovedbyCENon23September2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Sta

9、ndardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadeby

10、tra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvi

11、a,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinan

12、yformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO91005:2005:EEN ISO 9100-5:2005 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Dimensions.4 Bibliography 8 EN ISO 9100-5:2005 (E) 3 Foreword This document (EN ISO 9100-5:2005) has been prepared by Technical Com

13、mittee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR, in collaboration with Technical Committee ISO/TC 63 “Glass containers”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Ju

14、ly 2005, and conflicting national standards shall be withdrawn at the latest by July 2005. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. It is based on CE

15、.T.I.E (International Technical Centre for Bottling and Packaging) 1)data sheet GME 20-03 : 1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic

16、, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 1) Centre Technique International de lEmbouteillage (CETIE), 3, rue

17、La Botie, 75008 Paris, France, www.cetie.org EN ISO 9100-5:2005 (E) 4 1 Scope This document specifies the dimensions of vacuum lug finishes with a nominal size of 43 mm and 48 mm regular for wide-mouth glass containers. 2 Normative references Not applicable. 3 Dimensions 3.1 The design and dimension

18、 of the finish shall be as shown in Figures 1 to 3 and Table 1. 3.2 Details which are not specified shall be selected in accordance with the application. For general tolerances see EN 22768-1. Dimensions in millimetres Figure 1 Cutter profile EN ISO 9100-5:2005 (E) 5 Dimensions in millimetres Key a)

19、 Parting line b) See Figure 3 Figure 2 Thread construction and enlarged view section B-B EN ISO 9100-5:2005 (E) 6 Dimensions in millimetres Key a) The sealing surface shall be free of checks, dips, crizzles and other defects which may affect proper functioning. b) Proper system functioning calls for

20、 keeping the ovality in the finish diameters to a minimum. E and T diameters should be concentric in relation to one another. c) Cross-hatched areas of C diameter and H height show the closure position. Glass shall clear cap limits shown. The contour below the H dimension as well as the design of a

21、possible bead are optional. Sufficient free space shall be provided between the bead and the cross-hatched area. Figure 3 Enlarged view section A-A EN ISO 9100-5:2005 (E) 7 Table 1 Dimensions Thread parameters Thread parameters Type Diameter E (mm) Diameter T (mm) Diam- eter C (mm) Cutter a ) Leads

22、Pitch (mm) T.P.I. b ) 1 Pitch (mm) T.P.I. b ) 43 38,10 0,35 40,50 0,35 29,70 1520 4 1520 33,85 3/4 355 8,45 3 48 43,20 0,35 45,60 0,35 34,75 13394 1339 33,85 3/4 328 8,45 3 a ) The cutter inclination at -angle shall be maintained for all cuts. The start and end of the leads correspond to the cut-in

23、profile as defined by the cutter diameter, except where riffles are required to permit mould opening. b ) Threads per inch EN ISO 9100-5:2005 (E) 8 Bibliography EN 22768-1, General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:

24、1989) blankBS EN ISO 9100-5:2005 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Cha

25、rter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccu

26、racy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which

27、 ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also

28、available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information

29、 on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (

30、0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7

31、001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the c

32、opyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or oth

33、erwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.