EN 62053-31-1998 en Electricity Metering Equipment (a c ) Partricular Requirements Part 31 Pulse Output Devices for Electromechanical and Electronic Meters (Two Wires Only)《交流电测量设备.pdf

《EN 62053-31-1998 en Electricity Metering Equipment (a c ) Partricular Requirements Part 31 Pulse Output Devices for Electromechanical and Electronic Meters (Two Wires Only)《交流电测量设备.pdf》由会员分享，可在线阅读，更多相关《EN 62053-31-1998 en Electricity Metering Equipment (a c ) Partricular Requirements Part 31 Pulse Output Devices for Electromechanical and Electronic Meters (Two Wires Only)《交流电测量设备.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、 STD.BSI BS EN b2053-31-ENGL 1999 Sll Lh2YbbS 0755b5G 442 Electricity me tering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only) The European Standard EN 62053-61: 1998 has the status of a British Standard ICs 91.

2、140.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW ISEN EC i2053-3 1: 1999 i2053-3 1: 1998 - STD.BSI BS EM b2053-31-ENGL 1477 I lbZLibb9 0755051 387 direction of the Electrotechnicai No. Da - present to the responsible internationalEuropean committee any enquiries on the i

3、nterpretaiion, or propods for change, and keep the UK interests informed; - monitor related hternationai and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. From 1 January 1997, aU IEC publicaiion

4、s have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that

5、 CEN and CENELEC standards normally include an annex which lists nonnative references to international publications with their corresponding European publications. The British Standards which implement these intedonal or European publications may be found in the BSI Standards Catalogue under the sec

6、tion entitled “Inte - pulse output devices class B for short range and low power consumption. The pulse output shall generate a number of pulses proportional to the measured energy. 4.1.2 Electrical environment The physical interface of the pulse output device is described in annex A. The supply sou

7、rce for the output circuit shall originate from an external device (e.g. multi-rate unit) or other selected source. Page 7 EN 62053-31:1998 Maximum current in ON-state Minimum current in ON-state The main electrical characteristics are summarized in table 1. - 27 mA 15 mA 10 mA 2 mA Table 1 - Specif

8、ied operating conditions I Parameters I Clare A pulre device I Clans B nulee devlce 1 I Maximum voltage (ma,J I 27 V d.c. I 15 V d.c. I I Maximum current in OFF-state I 2 mA I 0,15 mA I NOTE 1 - The maximum distance of transmission is dependent on the environment and the quality of the cable, and mu

9、st be defined specifically. NOTE 2 - If other functions like detection of fraud, short circuit or open circuit in the transmission line, etc. are required, a solution with the values specified in annex E may be used. 4.1.3 Pulse characteristics 4.1.3.1 Output pulse waveform The pulses shall have the

10、 shape shown in figure B.l. 4.1.3.2 Supply polarity When the meter is equipped with several pulse outputs that have a common terminal this common terminal shall be negative. 4.1.3.3 Pulse duration The pulse duration foN is defined in figure B.l with foN 2 30 ms. The time between two successive pulse

11、s foFF is defined in figure B.1 with foFF 2 30 ms. 4.1.3.4 Transition time (ZT) The transition time (rise time or fall time) is the time from one state to the other, including transient effects, e.g. contact bounce. The transition time shall be less than 5 ms (see figure B.l). 4.2 Mechanical require

12、ments 4.2.1 General The features of the pulse device shall comply with ail mechanical requirements stated in the standard applying to the meter in which it is included. Refer to the appropriate standard. 4.2.2 Information on the pulse value in the form x (energy units)/imp or x imp/(energy units) sh

13、all be added on the meter name plate or on a separate plate (imp = pulse). Marking of the pulse value 4.3 Climatic conditions Refer to IEC 61036. Page ,8 EN 62053-31:1998 4.4 Electrical requirements 4.4.1 Interaction with the meter In order to ascertain that the pulse output device has no adverse in

14、fluence on the meter and the meter has no adverse influence on the pulse output device, the tests of the following clauses and subclauses shall be carried out and the requirements met, unless otherwise specified in this standard: - clause 6 Electrical requirements“ and clause 8 “Accuracy“ of IEC 601

15、45; - clause 6 “Electrical requirements“, clause 8 “Accuracy“, clause 9 “Starting and running with no load“ and clause 1 O “Adjustment“ of IEC 60521 ; - subclauses 4.4 “Electrical requirements“ and 4.6 “Accuracy requirements“ of IEC 60687, IEC 61036 and IEC 61268. 4.4.2 Power consumption For static

16、meters and electromechanical meters equipped with pulse output devices, the power consumption shall not exceed the values specified in table 1 of IEC 61899 for multi-function meters. 4.4.3 Influence of supply voltage 4.4.3.1 Voltage range Refer to IEC 61036. 4.4.3.2 Voltage dips and short interrupti

17、ons Voltage dips and short interruptions shall not cause more than one pulse. When the voltage is restored the pulse output device shall not have suffered degradation of its characteristics. For testing see 5.4.1. 4.4.4 Insulation The pulse output device shall withstand the impulse voltage test and

18、the a.c. voltage test, as specified in 5.4.6 of IEC 61 036. 4.5 Electromagnetic compatibility (EMC) 4.5.1 Immunity to electromagnetic disturbance The pulse output device shall be designed in such a way that conducted or radiated electromagnetic disturbance as well as electrostatic discharge do not d

19、amage or substantially influence the pulse output device or the meter in which it is included. For testing see 5.5.1 to 5.5.4. 4.5.2 Suppression of radio interference Meters equipped with pulse output devices shall not generate conducted or radiated noise which can interfere with other equipment. Fo

20、r testing, see 5.5.5. STD-BSI BS EN b2053-3L-ENGL 1777 D lb2i4bb7 U755bb0 311 P Page 9 EN 62053-31:1998 5 Tests and test conditions 5.1 General testing procedures 5.1.1 Test conditions All tests shall be carried out under r8.3rence conditions unless otherwise stated in the relevant subclause. 5.1.2

21、Type test The type test defined in 3.7.1 of IEC 61036 shall be made on one or more meters, equipped with a pulse output device selected by the manufacturer, to establish its specific characteristics and prove its conformity with the requirements of this standard. A recommended test sequence is given

22、 in annex F. 5.2 lests for mechanical requirements The tests shall be carried out on pulse output devices built into the appropriate meter. After the shock test and vibration test carried out as specified in IEC 61036, the pulse output devices shall fulfil the requirements for the meter under test.

23、5.3 Tests for climatic influences The following tests as specified in IEC 61036 shall be carried out: 5.3.1 dry heat test, 5.3.2 cold test and 5.3.3 damp heat cyclic test. After each of the climatic tests, the meter, including the pulse output device, shall show no damage or modification of informat

24、ion and shall operate correctly. 5.4 Tests for electrical requirements 5.4.1 The tests shall be carried out as per 5.4.2.1 of IEC 61 036. For requirements see 4.4.3.2. Tests for the effect of voltage dips and short interruptions 5.4.2 Tests for insulation properties No additional test is required wi

25、th respect to those normally conducted for the meter itself. 5.5 The tests shall be conducted on the meter including the pulse output device. The pulse output device shall be energized accordingly. After the tests the pulse output device shall fulfil the same requirements as specified in subclauses

26、5.5.2 to 5.5.5 for the test output of the meter. Tests for electromagnetic compatibility (EMC) 5.5.1 General test conditions For all these tests the meter, equipped with a pulse output device, shall be in its normal working position with the cover and terminal covers in place. All parts intended to

27、be earthed shall be earthed. The effective length of the output leads shall not exceed 1 m. STD-BSI BS EN b2053-31-ENGL 1477 I LbZLibbS 0755bbl 228 M Page IO EN 62053-311998 After these tests the pulse output device shall show no damage and operate correctly. 5.5.2 The test shall be carried out acco

28、rding to 5.5.2 of IEC 61036. Tests for immunity to electrostatic discharge 5.5.3 The test shall be carried out according to 5.5.3 of IEC 61036. 5.5.4 Tests for immunity to electromagnetic HF fieids Tests for fast transient burst The test shall be carried out according to 5.5.4 of IEC 61036. 5.5.5 Su

29、ppression of radio interference The test shall be carried out according to 5.5.5 of IEC 61036. 5.6 Functional tests The tests shall be carried out with the same reference conditions as the meter. Within the operating range the pulse output device shall operate correctly with regards to the number of

30、 pulses emitted, and the times bN and toFF shall remain within their specifed range. The test arrangement shall be according to annex C. Page 11 EN 62053-31:1998 I Pulse output U device v Annex A (normative) Pulse input device Physical interface of the pulse output STDmBSI BS EN b2053-3L-ENGL 1999 I

31、I Bb24bb9 0755bb3 OTO II Page 12 EN 62053-311998 Annex B (normative) Output pulse waveform Page 13 EN 62053-3k1998 State of pulre output Annex C (normative) Power supply Power supply internal Loop current (i) Voltage (u) voltage ( U.) resistance (R,) V kn mA v Test of pulse output device ON The test

32、 set-up is according to figure C.1. Class A Class B Class A I Class B Class A Class B Class A Class B 18 3 1 - 10 - w2 - e8 - 14 27 15 1 - 25 IEC 130D - Figure C.l - Pulse output device test Set-up The pulse output device shall fulfil the requirements of the following table. I I I I I I I I I Page 1

33、4 EN 62053-311998 ,I U W Annex D (inform at ive) Puise input device Test of pulse input device Switch pomition The test Set-up is according to figure D.1. Test rerults; Resistance value Remarks loop current or voltage Cass 1 Ciam B 1 2 3 IEC 140/88 R1=800n Pulse input power supply I210mA l22mA ms1n

34、ShoR-circuit current of pulse Ie27mA 1el5mA input device input device IBlMR Open-circuit voltage of puise Ui27V us15v Figure D.l - Pulse input device test Set-up The pulse input device shall fulfil the requirements of the following table. STD-BSI BS EN b2053-3L-ENGL 1947 Lb24Lb7 0755bbL BOT I Parame

35、ters Open circuit (/,) Rest (OFF) (/,) Defraudation (Id) Measure puise (ON) (/,) Defraudation + Measure pulse f/dd Page 16 EN 62053-311998 Minimum Maximum O mA 1MR Open circuit O 5 lo c 4 rnA 5 6 Rs=3kR Defraudation 6,5 S Id 8,Q mA R = 1,7 ki2 Pulse + Defraudation 11,4 /dp 14 mA I I I I U30Vd.c. I -

36、1 R4=4ki2 I Rest I 4s hc 6.5 mA I I-% Page 19 EN 62053-31:1998 No. 1 Annex F (informative) Tests Subclause Tests of insulation properties 5.4.2 Test schedule 3 3.1 4 Recommended test sequence Tests for electrical requirements Tests for the effect of voltage dips and short interruptions 5.4.1 Tests f

37、or electromagnetic compatibility 4.1 4.2 4.3 I 2 Functional tests I 5.6 I Suppression of radio interference 5.5.5 Tests for fast transient burst Test for immunitv to electromannetic HF fields 5.5.4 5.5.3 5 6 Test for climatic influences 5.3 Tests for mechanical reauirements 5.2 I 4.4 I Test for immu

38、nity to electrostatic discharge I 5.5.2 I Page 20 EN 62053-31:1998 I I Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These n

39、ormative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated r

40、eferences the latest edition of the publication referred to applies (including amendments). NOTE: When an international publication has been modified by common modifications, indicate by (mod), the relevant ENIHD applies. Publication - Year IEC 60145 1963 IEC 60381-1 1982 IEC 60521 1988 IEC 60687 19

41、92 IEC 61036 1996 IEC 61268 1995 IEC 62053-61” 1998 Var-hour (reactive energy) meters Analogue signals for process control systems Part 1 : Direct current signals Class 03, 1 and 2 alternating-current watt-hour meters Alternating current static watt-hour meten for active energy- (classes 0,2 S and 0

42、,5 S) Alternating current static watt-hour meters for active energy (classes 1 and 2) Alternating current static var-hour meters for reactive energy (classes 2 and 3) Electricity metering equipment (a.c.) Particular requirements Part 61 : Power consumption and voltage requirements E”D HD452.1 Sl EN

43、60521 + con. December EN 60687 + con. March EN 61036 EN 61268 EN 62053-61 - Year - 1984 1995 1997 1992 1993 1996 1996 1998 li This document was wote as prEN 61 899. STD-BSL BS EN b2053-31-ENGL 1777 Lb24bb7 U755b72 OU3 E BS EN 62053-311999 IEC 62053-3 1: 1998 BSI 389 Chiswick High Road I London w4 4A

44、L 3SI - British Standards Institution ;SI is the independent national body responsible for preparing British Standards. It resents the UK view on standards in Europe and at the international level. It is icorporated by Royal Charter. Cevisions lritish Standasdc are updated by amendment or revision.

45、Users of British Standards hould make sure that they possess the latest amendments or editions. t is the constant aim of BSI to improve the quality of our products and services. We vould be grateful if anyone finding an inaccuracy or ambiguity while using this hitish Standard would inform the Secret

46、ary of the technical committee responsible, he identity of which can be found on the inside front cover. Tel 0181 996 9000. tax: 0181 996 7400. 3SI offers members an individual updating service called PLUS which ensures that ubscribers automatically receive the latest editions of standards. hying st

47、andards Irders for all BSI, international and foreign standards publications should be uidressed to Customer Services. Tel O181 996 7000. Fax: 0181 996 7001. n response to orders for international standxds, it is BSI policy to supply the BSI mplementation of those that have been published as British

48、 Standards, unless )therwise requested. hformation on standards 3SI provides a wide range of information on national, European and international ;tandards through its Library and its Technical Help to Exporters Service. Various 3SI electronic information services are also available which give detail

49、s on all its iroducts and services. Contact the Information Centre. Tel 0181 996 7111. ?ax: 0181 996 7048. hbscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of hese and other benefits contact Membership Administxition. Tel 0181 996 7002. Fax: 0181 996 7001. Copyright Copyright subsists in ali BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as