EN 61169-47-2012 0625 Radio-frequency connectors - Part 47 Sectional specification for radio-frequency coaxial connectors with clamp coupling typically for use in 75 Ω cable networ.pdf

《EN 61169-47-2012 0625 Radio-frequency connectors - Part 47 Sectional specification for radio-frequency coaxial connectors with clamp coupling typically for use in 75 Ω cable networ.pdf》由会员分享，可在线阅读，更多相关《EN 61169-47-2012 0625 Radio-frequency connectors - Part 47 Sectional specification for radio-frequency coaxial connectors with clamp coupling typically for use in 75 Ω cable networ.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationRadio-frequency connectorsPart 47: Sectional specification for radio-frequency coaxial connectors with clamp coupling, typically for use in 75 null cable networks (type F-Quick)B

2、S EN 61169-47:2012Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN 61169-47:2012. It is

3、identical to IEC 61169-47:2012.The UK participation in its preparation was entrusted to Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained on reque

4、st to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013 ISBN 978 0 580 75060 1 ICS 33.120.30Compliance with a British

5、 Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate Text affectedBRITISH STANDARDBS EN 61169-47:2012Copyright European Committee for E

6、lectrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD EN 61169-47 NORME EUROPENNE EUROPISCHE NORM November 2012 CENELEC European Committee for Electrotechnical Standardization Com

7、it Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61169-47:2012 E ICS 33.120.3

8、0 English version Radio-frequency connectors - Part 47: Sectional specification for radio-frequency coaxial connectors with clamp coupling, typically for use in 75 cable networks (type F-Quick) (IEC 61169-47:2012) Connecteurs pour frquences radiolectriques - Partie 47: Spcification intermdiaire rela

9、tives aux connecteurs coaxiaux pour frquences radiolectriques avec couplage par bride, spcifiquement utiliss dans les rseaux cbls 75 (type F-Quick) (CEI 61169-47:2012) Hochfrequenzsteckverbinder -Teil 47: Rahmenspezifikation - Koaxiale Hochfrequenzsteckverbinder mit Klemmkupplung, vorzugsweise fr de

10、n Einsatz in 75-Kabelnetzen (Typ F-Quick) (IEC 61169-47:2012) This European Standard was approved by CENELEC on 2012-08-28. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard

11、 without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in a

12、ny other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia

13、, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey

14、and the United Kingdom. BS EN 61169-47:2012Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 61169-47:2012 - 2 - Foreword The text of document 46F/204/CDV,

15、future edition 1 of IEC 61169-47, prepared by SC 46F, “R.F. and microwave passive components“, of IEC TC 46, “Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61169-47:2012.

16、 The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-05-28 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-08-2

17、8 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61169-47:2012 was appr

18、oved by CENELEC as a European Standard without any modification. BS EN 61169-47:2012Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 3 - EN 61169-47:2012 Ann

19、ex ZA(normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies

20、. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61169-1 + A1 + A2 1992 1

21、996 1997 Radio-frequency connectors - Part 1: Generic specification - General requirements and measuring methods EN 61169-1 + A1 + A2 1994 1996 1997 IEC 61169-24 2009 Radio-frequency connectors - Part 24: Sectional specification - Radio frequency coaxial connectors with screw coupling, typically for

22、 use in 75 ohm cable networks (type F) EN 61169-24 2009 BS EN 61169-47:2012Copyright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 2 61169-47 IEC:2012(E) CONTENTS 1

23、 Scope . 5 2 Normative references . 5 3 Interface dimensions 5 Dimensions . 5 3.1Common dimensions . 5 3.1.1Example of connector “F-Quick” type male plug with resilient outer 3.1.2conductor sleeve (indoor) physical dimensions 6 Example of connector “F-Quick” type male plug with slotted outer 3.1.3co

24、nductor (indoor) physical dimensions . 7 Example of connector “F-Quick” type male plug with slotted outer 3.1.4conductor and snap ring (indoor) physical dimensions . 7 Mechanical gauges 8 3.24 Quality assessment procedures 9 General . 9 4.1Ratings and characteristics . 9 4.2Environmental characteris

25、tics for outdoor sockets . 11 4.3Test schedule and inspection requirements . 11 4.4Acceptance tests . 11 4.4.1Periodic tests. 11 4.4.2Procedures 13 4.5Quality conformance inspection . 13 4.5.1Qualification approval and its maintenance 13 4.5.25 Instructions for preparation of detail specifications .

26、 13 General . 13 5.1Identification of the detail specification 14 5.2Identification of the component 14 5.3Performance 14 5.4Marking, ordering information and related matters . 14 5.5Selection of tests, test conditions and severities 14 5.6Blank detail specification pro-forma for type F connector .

27、15 5.7Figure 1 Connector “F-Quick” type male plug: General dimensions 6 Figure 2 Example of connector “F-Quick” type male plug with resilient outer conductor sleeve (indoor) . 7 Figure 3 Example of connector “F-Quick” type male plug with slotted outer conductor (indoor) . 7 Figure 4 Example of conne

28、ctor “F-Quick” type male plug with slotted outer conductor and snap ring (indoor) . 8 Figure 5 Mechanical gauge 8 Table 1 Connector “F” type male plug (indoor) . 6 Table 2 Ratings and characteristics (1 of 2) . 9 Table 3 Acceptance tests . 11 Table 4 Periodic tests (1 of 2) 12 BS EN 61169-47:2012Cop

29、yright European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61169-47 IEC:2012(E) 5 RADIO-FREQUENCY CONNECTORS Part 47: Sectional specification for radio-frequency coaxial c

30、onnectors with clamp coupling, typically for use in 75 cable networks (type F-Quick) 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with clamp coupling, typically for

31、use in 75 cable networks (type F-Quick). It describes the interface dimensions with gauging information, electrical and mechanical performance including the mandatory tests selected from IEC 61169-1:1992, applicable to all DS relating to type F-Quick connectors. This specification indicates the reco

32、mmended performance characteristics to be considered when writing a DS and covers test schedules and inspection requirements. NOTE This interface is typically used for indoor connections, which are easily disconnected and reconnected. The typical application is for F-type coaxial receiver leads or F

33、-type coaxial patch cables. The interface may also be known as a Push On connector. It is preferred to use the fixed (screwed) connectors type F according to IEC 61169-24:2009. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are in

34、dispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuri

35、ng methods1Amendment 1:1996 Amendment 2:1997 IEC 61169-24:2009, Radio-frequency connectors Part 24: Sectional specification Radio frequency coaxial connectors with screw coupling, typically for use in 75 cable networks (type F) 3 Interface dimensions Dimensions 3.1Common dimensions 3.1.1Millimetres

36、are original dimensions. All un-dimensioned pictorial configurations are for reference purposes only. _ 1There exists a consolidated edition 1.2 (1998) that comprises IEC 61169-1:1992, its Amendment 1:1996 and its Amendment 2:1997. BS EN 61169-47:2012Copyright European Committee for Electrotechnical

37、 Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 6 61169-47 IEC:2012(E) Figure 1 and Table 1 depict the dimensions that are common to any F connector and thus indispensable for compatibility. Examples of sp

38、ecific design with their dimensions are given in 3.1.2 to 3.1.4. EC0,100 A GFDB A Reference plane IEC 1462/12 Figure 1 Connector “F-Quick” type male plug: General dimensions Table 1 Connector “F” type male plug (indoor) DESCRIPTION DIM mm inches NOTES Min. Max. Min. Max. Inner conductor length A 6,3

39、5 8,63 0,250 0,340 Length of nut B 4,00 7,29 0,167 0,287 Maximum envelope dimension C 16,61 0,654 Inner conductor diameter D 0,64 1,13 0,025 0,044 Reference plane opening inner diameter F 6,84 0,230 1 Reference plane outer diameter G 7,11 0,280 1 No protrusion of the dielectric beyond the reference

40、plane is permitted. Example of connector “F-Quick” type male plug with resilient outer conductor 3.1.2sleeve (indoor) physical dimensions The connector is shown in Figure 2. Common dimensions are given in 3.1.1. BS EN 61169-47:2012Copyright European Committee for Electrotechnical Standardization Pro

41、vided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61169-47 IEC:2012(E) 7 Dimension in millimetres Resilient sleeve Cone or radius 8,55 1Min. 7,5 IEC 1463/12 Figure 2 Example of connector “F-Quick” type male plug with resilient o

42、uter conductor sleeve (indoor) Example of connector “F-Quick” type male plug with slotted outer conductor 3.1.3(indoor) physical dimensions The connector is shown in Figure 3. Common dimensions are given in 3.1.1. Dimension in millimetres Minimum 6 slotted 9,55 +0,10 IEC 1464/12 Figure 3 Example of

43、connector “F-Quick” type male plug with slotted outer conductor (indoor) Example of connector “F-Quick” type male plug with slotted outer conductor 3.1.4and snap ring (indoor) physical dimensions The connector is shown in Figure 4. Common dimensions are given in 3.1.1. BS EN 61169-47:2012Copyright E

44、uropean Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 8 61169-47 IEC:2012(E) Dimension in millimetres Min. 7,5 1Snap ring Cone or radius 9,100,1IEC 1465/12 Figure 4 Example

45、of connector “F-Quick” type male plug with slotted outer conductor and snap ring (indoor) Mechanical gauges 3.2See IEC 61169-24:2009 for the test procedure using the gauge as defined in Figure 5. NOTE 2 NOTE1BC D 3/8-32 UNEF-2A with major A AEIEC 1466/12 DESCRIPTION Dimension mm inches Outside diame

46、ter of thread blank A 9,34 0,368 Reference plane opening outer diameter B 7,48 0,295 Port thread length C 7,48 0,295 Port length D 12,69 0,357 Bulkhead diameter E 16,59 0,654 1 Outside diameter of thread. 2 Thread relief not to exceed 2 full threads. Figure 5 Mechanical gauge BS EN 61169-47:2012Copy

47、right European Committee for Electrotechnical Standardization Provided by IHS under license with CENELECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-61169-47 IEC:2012(E) 9 4 Quality assessment procedures General 4.1The following subclauses provide recommended ra

48、tings, performance and test conditions to be considered when writing a detail specification (DS). They also provide an appropriate schedule of tests with minimum levels of conformance inspection. Ratings and characteristics 4.2The RF connectors defined in this standard are designed for use with a variety of flexible and semi-rigid coaxial cables and in microwave integrated circuits and similar uncabled applications. Table 2 Ratings and character