EN 16285-2013 en Packaging - Flexible aluminium tubes - Test method to measure the deformation of the aluminium tube body (Guillotine test)《灵活的铝管包装测试方法 测量铝管体的变形(断头台测试)》.pdf

《EN 16285-2013 en Packaging - Flexible aluminium tubes - Test method to measure the deformation of the aluminium tube body (Guillotine test)《灵活的铝管包装测试方法 测量铝管体的变形(断头台测试)》.pdf》由会员分享，可在线阅读，更多相关《EN 16285-2013 en Packaging - Flexible aluminium tubes - Test method to measure the deformation of the aluminium tube body (Guillotine test)《灵活的铝管包装测试方法 测量铝管体的变形(断头台测试)》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16285:2013Packaging Flexiblealuminium tubes Testmethod to measure thedeformation of the aluminiumtube body (Guillotine test)BS EN 16285:2013 BRITISH STANDARDNational forewo

2、rdThis British Standard is the UK implementation of EN 16285:2013.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/10, Packaging - Plastics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not pu

3、rport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 74959 9ICS 55.120Compliance with a British Standard cannot confer immunity fromlegal obligations.

4、This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationDate Text affectedBS EN 16285:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16285 February 2013 ICS 55.120 English Version Packaging

5、 - Flexible aluminium tubes - Test method to measure the deformation of the aluminium tube body (Guillotine test) Emballage - Tubes souples en aluminium - Mthode dessai pour mesurer la dformation du corps du tube en aluminium (essai Guillotine) Packmittel - Aluminiumtuben - Prfverfahren zur Messung

6、der Verformung des Mantels von Aluminiumtuben (Guillotine-Prfung) This European Standard was approved by CEN on 21 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standa

7、rd without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

8、 other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Repub

9、lic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN

10、COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16285:2013: EBS EN 16285:2013EN 1

11、6285:2013 (E) 2 Contents Page Foreword . 3 1 Scope . 42 Testing equipment 43 Requirements . 54 Execution 55 Test report 6BS EN 16285:2013EN 16285:2013 (E) 3 Foreword This document (EN 16285:2013) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFN

12、OR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at the latest by August 2013. Attention is drawn to the possibility that some

13、 of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to imple

14、ment this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

15、 Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16285:2013EN 16285:2013 (E) 4 1 Scope This European Standard specifies a method to measure the deformation of the aluminium tube body. It is applicable to cylindrical aluminium tubes used for packing pharmaceutical

16、, cosmetic, hygiene, food and other domestic and industrial products. 2 Testing equipment The testing equipment (see Figure 1) shall conform to the information given below. Appropriate data should be chosen where no details are given. Key 1 locking lever for drop weight 2 upper edge of drop weight 3

17、 drop weight 4 lower edge of drop weight burr-free 5 prism-shaped support 6 limit stop 7 base plate 8 width of guide groove 9 scale Figure 1 Test equipment BS EN 16285:2013EN 16285:2013 (E) 5 With the drop weight locked in position (the situation shown), the lower edge of the drop weight is in line

18、with the value 0 on the scale. If the drop weight is released and there is no test piece, the drop weight will rest on the base plate. The upper edge of the drop weight then corresponds to the value 0 on the scale. The scale is 0 mm to 120 mm. The width of the guide groove is 5,3200,+mm. The height

19、of the fall of the drop weight is (115 1) mm. The thickness of the drop weight is 5100,+mm. The total weight is (25 0,1) g or (75 0,1) g. The distance between the drop weight and the limit stop is 32 mm. 3 Requirements When carrying out tests according to Clause 4, the deformation values shall confo

20、rm to the values given in Table 1. Table 1 Deformation values Nominal diameter of tube mm Weight of drop weight g Deformation values min in mm a) max 11 25 1 4 13,5 4 7 16 5 9 19 8 1222 11 15 25 75 8 1328 9 1430 11 1732 13 2035 16 24 38 19 2740 23 3145 28 3650 33 43a) The deformation values are base

21、d on tubes with and without internal lacquer. Tighter tolerances are subject to agreement between the producer and the user. 4 Execution Testing is carried out on an empty tube at room temperature. The drop weight having the appropriate test weight for the tube diameter as given in the table is rais

22、ed until the locking lever engages. The tube to be tested is placed in the prism-shaped support of the base plate in such a way that it abuts against the limit stop. Using the locking lever, the drop weight is released manually so that it drops down. In doing so it compresses the tube being tested b

23、y an amount equal to its deformation value. This is read off the scale. BS EN 16285:2013EN 16285:2013 (E) 6 5 Test report The test report shall contain the following information: a) reference to this standard and, if necessary, a specification for the method of sampling and acceptance of the batch;

24、b) the complete identification of the batch and of the tubes checked; c) the date of production; d) the number of tubes checked; e) the number of defects; f) the test result; g) all factors which could have affected the results or all operating details not specified in this standard; h) date, place

25、of test and name of tester. This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is inco

26、rporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodicall

27、y updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while usin

28、g British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual

29、 updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Sh

30、op on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of

31、the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up t

32、o date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PA

33、Ss via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that

34、own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system

35、or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: