EN 14545-2008 en Timber structures - Connectors - Requirements《木材结构 连接器 要求》.pdf

《EN 14545-2008 en Timber structures - Connectors - Requirements《木材结构 连接器 要求》.pdf》由会员分享，可在线阅读，更多相关《EN 14545-2008 en Timber structures - Connectors - Requirements《木材结构 连接器 要求》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 14545:2008ICS 91.080.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTimber structures Connectors RequirementsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 April2009 BSI 2009ISBN 978 0 580 58745

2、0Amendments/corrigenda issued since publicationDate CommentsBS EN 14545:2008National forewordThis British Standard is the UK implementation of EN 14545:2008.The UK participation in its preparation was entrusted to TechnicalCommittee B/518, Structural timber.A list of organizations represented on thi

3、s committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 14545:2008EUROPEAN ST

4、ANDARDNORME EUROPENNEEUROPISCHE NORMEN 14545October 2008ICS 91.080.20English VersionTimber structures - Connectors - RequirementsStructures en bois - Connecteurs - Exigences Holzbauwerke - Nicht stiftfrmige Verbindungselemente -AnforderungenThis European Standard was approved by CEN on 9 August 2008

5、.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on ap

6、plication to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre

7、has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por

8、tugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means r

9、eservedworldwide for CEN national Members.Ref. No. EN 14545:2008: EBS EN 14545:2008EN 14545:2008 (E) 2 Contents Page Foreword .3 1 Scope 4 2 Normative references4 3 Terms and definitions .5 4 Symbols and abbreviations5 5 Dimensions and tolerances6 5.1 Method of measurement and accuracy.6 5.2 Length.

10、6 5.3 Width.6 5.4 Diameter .6 5.5 Thickness .6 5.6 Other dimensions 7 6 Requirements.7 6.1 Shear plates, split ring and toothed-plate connectors 7 6.1.1 Materials .7 6.1.2 Geometry7 6.1.3 Mechanical strength and stiffness.7 6.1.4 Corrosion protection.7 6.2 Punched metal plate fasteners.7 6.2.1 Mater

11、ials .7 6.2.2 Geometry8 6.2.3 Mechanical strength and stiffness.8 6.2.4 Corrosion protection.8 6.3 Nailing plates .9 6.3.1 Materials .9 6.3.2 Geometry9 6.3.3 Mechanical strength and stiffness.9 6.3.4 Corrosion protection.9 7 Evaluation of conformity 10 7.1 General .10 7.2 Initial type testing (ITT)

12、.10 7.2.1 General .10 7.2.2 Sampling, testing and conformity criteria 10 7.3 Factory production control (FPC)13 7.3.1 General .13 7.3.2 Control 14 8 Marking.19 8.1 General .19 8.2 Shear plate, split ring and toothed plate connectors 19 8.3 Punched metal plate fasteners.19 8.4 Nailing plates .19 Anne

13、x A (normative) Expression of corrosion protection specifications.21 Annex B (normative) Procedures for the derivation of mechanical strength and stiffness characteristics of punched metal plate fasteners22 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU

14、Construction Products Directive .27 Bibliography36 BS EN 14545:2008EN 14545:2008 (E) 3 Foreword This document (EN 14545:2008) has been prepared by Technical Committee CEN/TC 124 “Timber Structures”, the secretariat of which is held by SFS. This European Standard shall be given the status of a nation

15、al standard, either by publication of an identical text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig

16、hts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationsh

17、ip with EC Directive(s), see informative Annex ZA, which is an integral part of this document. This standard also includes two normative annexes covering corrosion protection specifications for connectors covered by this standard, and procedures for the derivation of characteristic strength properti

18、es of punched metal plate fasteners. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greec

19、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 14545:2008EN 14545:2008 (E) 4 1 Scope This European Standard specifies requirements and test methods

20、 for materials, geometry, strength, stiffness and durability aspects (i.e. corrosion protection) of connectors for use in load bearing timber structures. Only connectors manufactured from steel are covered by this European Standard, like shear plates, split ring connectors, tooth plate connectors, p

21、unched metal plate fasteners and nailing plates. Definitions of these items are given in Clause 3. This European Standard specifies also the evaluation of conformity procedures and includes requirements for marking of these products. This European Standard does not cover connectors treated with fire

22、 retardants to improve their fire performance. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

23、amendments) applies. EN 912:1999, Timber fasteners - Specifications for connectors for timber EN 1075:1999, Timber structures - Test methods - Joints made with punched metal plate fasteners EN 1995-1-1:2004, Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for bui

24、ldings EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels EN 10029, Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and mass EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of no

25、n-alloy and alloy steels - Tolerances on dimensions and shape EN 10088-1, Stainless steels - Part 1: List of stainless steels. EN 10088-2, Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10143, Continuously hot-

26、dip coated steel sheet and strip - Tolerances on dimensions and shape EN 10204, Metallic products - Types of inspection documents EN 10292, Continuously hot-dip coated strip and sheet of steels with high yield strength for cold forming - Technical delivery conditions EN 10326, Continuously hot-dip c

27、oated strip and sheet of structural steels - Technical delivery conditions EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming -Technical delivery conditions EN 13271:2001, Timber fasteners - Characteristic load-carrying capacities and slip-moduli for connecto

28、r joints BS EN 14545:2008EN 14545:2008 (E) 5 EN 14358:2006, Timber structures - Calculation of characteristic 5-percentile values and acceptance criteria for a sample EN 26891, Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deform

29、ation characteristics (ISO 6891:1983) EN 28970:1991, Timber structures - Testing of joints made with mechanical fasteners - Requirements for wood density (ISO 8970:1989) EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:1999) E

30、N ISO 9001, Quality management systems - Requirements (ISO 9001:2000) EN ISO 9445, Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002) ISO 2081, Metallic coatings - Electroplated coatings of zinc on iron o

31、r steel 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1995-1-1:2004 and the following apply. 3.1 connector shear plates, split ring connectors or tooth plate connectors as defined in EN 912 and punched metal plate fasteners or nailing plates as defi

32、ned below 3.2 nailing plate flat rectangular metal plate containing pre-punched holes through which nails or screws are inserted NOTE Used either on the external faces of a joint to join two or more pieces of timber of the same thickness in the same plane or on one external face of a timber member f

33、or anchoring and bracing. 3.3 punched metal plate fastener metal plate having integral projections punched out in one direction perpendicular to the base of the plate NOTE Used to join two or more pieces of timber of the same thickness in the same plane. 3.4 plate thickness nominal steel plate thick

34、ness including the thickness of any corrosion protection coating 3.5 stiffness (slip modulus) the value of kserdefined in EN 26891, calculated per fastener and per shear plane 4 Symbols and abbreviations For the purposes of this standard, the symbols and abbreviations given in EN 1995-1-1:2004, EN 1

35、4358:2006, EN 13271:2001, EN 912:1999 and the following ones apply. A80percentage elongation (%) dcconnector diameter defined in EN 13271 (mm) BS EN 14545:2008EN 14545:2008 (E) 6 fa,kcharacteristic punched metal plate anchorage capacity (N/mm2) fv,k characteristic punched metal plate shear capacity

36、(N/mm) ft,k characteristic punched metal plate tension capacity (N/mm) fc,k characteristic punched metal plate compression capacity (N/mm) kser slip modulus per shear plane per fastener (N/mm3) ksstatistical constant defined in EN 14358 k1, k2, 0 constants used to characterise the shape of the punch

37、ed metal plate anchorage capacity kv, 0 constants used to characterise the shape of the punched metal plate shear capacity l overall connector length (mm) tp metal plate thickness (mm) w overall connector width (mm) maximum bend angle (degrees) k characteristic timber density (kg/m3) m mean timber d

38、ensity (kg/m3) 5 Dimensions and tolerances 5.1 Method of measurement and accuracy Length and width of the connectors shall be measured using a device capable of achieving an accuracy of 0,5 mm. Thickness and diameter shall be measured using a calibrated device capable of achieving an accuracy of 1 %

39、. 5.2 Length Where appropriate, the overall length of the connector shall be measured and the result declared. When sampled in accordance with Tables 2, 3 and 4 and Tables 5, 6 and 7 and measured, the overall length shall be within 1 mm/+ 2 mm or 1 %/+ 2 %, whichever is the greater, of its declared

40、value. 5.3 Width Where appropriate, the overall width of the connector shall be measured and the result declared. When sampled in accordance with Tables 2, 3 and 4 and Tables 5, 6 and 7 and measured, the overall width shall be within 1 mm/+ 2 mm or 1 %/+ 2 %, whichever is the greater, of its declare

41、d value. 5.4 Diameter Where appropriate, the connector diameter shall be measured and the result declared. Where tolerances on diameter are not otherwise given in EN 912, when sampled in accordance with Tables 2 and 4 and Tables 5 and 7 and measured to an accuracy of 0,01 mm, the nominal diameter sh

42、all be within 2,5 % of its declared value. 5.5 Thickness Where appropriate, the thickness of the connector shall be measured and the result declared. When sampled in accordance with Tables 2, 3 and 4 and Tables 5, 6 and 7 and measured, the plate thickness shall be within the tolerances specified for

43、 the parent plate material being used. BS EN 14545:2008EN 14545:2008 (E) 7 5.6 Other dimensions Where appropriate, other dimensions, e.g. tooth length, etc., shall be measured and result declared. When sampled in accordance with Tables 2 and 3 and measured these dimensions shall be within greater of

44、 0,75 mm or 2,5 % of the specified values given. 6 Requirements 6.1 Shear plates, split ring and toothed-plate connectors 6.1.1 Materials For shear plates, split ring connectors and toothed-plate connectors manufactured from steel specified in EN 912, the minimum material specifications shall be as

45、given in that standard. 6.1.2 Geometry For shear plates, split ring connectors and toothed-plate connectors specified in EN 912, the geometric values specified (i.e. dimensions and tolerances) shall be as given in that standard. 6.1.3 Mechanical strength and stiffness For joints formed using shear p

46、lates, split ring connectors and toothed-plate connectors specified in EN 912, the following characteristics shall be determined according to EN 13271 for: a) mechanical strength: as characteristic load bearing capacity, and b) mechanical stiffness: as slip modulus. NOTE The equations for the load-b

47、earing capacity of joints made with the connectors covered by EN 912 are given in EN 1995-1-1. 6.1.4 Corrosion protection For shear plates, split ring connectors and toothed-plate connectors covered by EN 912, the corrosion protection specifications shall be as given in that standard and shall be de

48、clared as appropriate service class according to EN 1995-1-1. Examples of minimum corrosion protection or material specifications for different service classes are given in EN 1995-1-1. 6.2 Punched metal plate fasteners 6.2.1 Materials Punched metal plate fasteners shall be formed from the steel spe

49、cifications given in Table 1 and shall have a minimum elongation (A80) of 16 %. BS EN 14545:2008EN 14545:2008 (E) 8 Table 1 Minimum steel specifications Type Reference Minimum specification Mild steel plate or strip EN 10327 DX51D EN 10326 S220GD 10292 HX220YD Austenitic stainless steel plate EN 10088-2 X5CrNiTi 18-10 6.2.2 Geometry Punched metal plate fasteners shall be produced from steel having a plate thickness tpof minimum 0,9 mm and of maximum 3,0 mm. The tolerance on the plate thickness shall be in accordance with EN 10143 for mild