EN 3080-2006 en Aerospace series - Pipe coupling 8 - in titanium alloy - Tees reduced branch with thrust wire nut《航空航天系列 钛合金830-管连接件 带止推金属丝螺母的缩短三通》.pdf

《EN 3080-2006 en Aerospace series - Pipe coupling 8 - in titanium alloy - Tees reduced branch with thrust wire nut《航空航天系列 钛合金830-管连接件 带止推金属丝螺母的缩短三通》.pdf》由会员分享，可在线阅读，更多相关《EN 3080-2006 en Aerospace series - Pipe coupling 8 - in titanium alloy - Tees reduced branch with thrust wire nut《航空航天系列 钛合金830-管连接件 带止推金属丝螺母的缩短三通》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3080:2006Aerospace series Pipe coupling 830 in titanium alloy Tees, reduced, branch with thrust wire nut The European Standard EN 3080:2006 has the status of a British StandardICS 49.080g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50

2、g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3080:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 49152 8National forewordThis Briti

3、sh Standard was published by BSI. It is the UK implementation of EN 3080:2006.The UK participation in its preparation was entrusted to Technical Committee ACE/69, Aerospace hydraulic systems, fluids and components. A list of organizations represented on ACE/69 can be obtained on request to its secre

4、tary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD

5、NORME EUROPENNE EUROPISCHE NORM EN 3080 July 2006 ICS 49.080 English Version Aerospace series - Pipe coupling 830 in titanium alloy - Tees, reduced, branch with thrust wire nut Srie arospatiale - Systme de raccordement 830 en alliage de titane - Raccords en t, de rduction branche avec crou jonc Luft

6、- und Raumfahrt - Rohrverschraubung 830 aus Titanlegierung - T-Verschraubungen, reduziert, seitlicher Auslass mit Mutter mit Schubdraht This European Standard was approved by CEN on 13 January 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditi

7、ons for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three of

8、ficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria

9、, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STA

10、NDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3080:2006: EEN 3080:2006 (E) 2 Contents Page For

11、eword3 1 Scope 4 2 Normative references 4 3 Required characteristics.5 4 Designation . 10 5 Marking 10 6 Technical specification 10 EN 3080:2006 (E) 3 Foreword This European Standard (EN 3080:2006) has been prepared by the AeroSpace and Defense Industries As-sociation of Europe Standardization (ASD-

12、STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has re-ceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the s

13、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2007, and conflicting national standards shall be withdrawn at the latest by January 2007. Attention is drawn to the possibility that some of the elements of this document may be the

14、subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium

15、, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem-bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer-land and the United Kingdom. EN 3080:2006 (E) 4 1 Scope T

16、his standard specifies the characteristics of tees, reduced, branch with thrust wire nut, for pipe couplings 830, in titanium alloy, for aerospace applications. Nominal pressure: up to 28 000 kPa. Temperature range: 55 C to 135 C. 2 Normative references The following referenced documents are indispe

17、nsable for the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5855-3, Aerospace series MJ threads Part 3: Limit dimensions for fittings for fluid system

18、s. EN 2424, Aerospace series Marking of aerospace products. EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods. EN 3264, Aerospace series Pipe coupling 830 in titanium alloy Thrust wire nut. EN 3273, Aerospace series Pipe coupling 830 Dynamic beam seal end for elbows, tee

19、s and crosses Geometric configuration. EN 3274, Aerospace series Pipe coupling 830 Thread Geometric configurations. EN 3275, Aerospace series Pipe coupling 830 up to 28 000 kPa Dynamic beam seal Metric series Technical specification. EN 3311, Aerospace series Titanium alloy TI-P64001 Annealed Bar fo

20、r machining D 150 mm.1)EN 3312, Aerospace series Titanium alloy TI-P64001 Grade 2 Annealed Forgings De 150 mm.1) EN 3314, Aerospace series Titanium alloy TI-P64001 Solution treated and aged Bar for machining D 75 mm.1) EN 3315, Aerospace series Titanium alloy TI-P64001 Solution treated and aged Forg

21、ings De 75 mm.1) EN 4032, Aerospace series Pipe coupling 830 in titanium alloy Thrust wire. 1) Published as ASD Prestandard at the date of publication of this standard. EN 3080:2006 (E) 5 3 Required characteristics The requirements apply to the tees. 3.1 Configuration Dimensions Mass According to Fi

22、gures 1 and 2 and Tables 1 and 2. Dimensions apply before lubricating. Dimensions not specified are at manufacturers option provided that the qualification and acceptance require-ments of EN 3275, type II are met. Connections 1 and 3 shall be connection 2. 3.2 Surface roughness According to Figure 1

23、, unless otherwise specified in the design documentation. 3.3 Materials According to EN 3311 or EN 3314, EN 3312 or EN 3315. 3.4 Surface treatment Lubrication: according to EN 2491, on threads, sealing faces and contact area between thrust wire and coupling. 3.5 Internal surface finishing Finishing

24、shall give a radius R of 0,3 mm to 1,0 mm and a surface roughness of 0,8 m. Hand deburring is not permitted. EN 3080:2006 (E) 6 Dimensions in millimetres Key 1 Nut according to EN 3264 2 Thrust wire according to EN 4032 aConnection 1 bConnection 2 cConnection 3 dThread 1 eThread 2 fAccording to EN 3

25、274, form C gArea for marking hAcross flats s2 iAccording to EN 3273 jR 0,3 to 1,0 kFully inserted Figure 1 EN 3080:2006 (E) 7 Table 1 Dimensions in millimetres Thread 1bThread 2bl1c,dl2cl3cl4cl5el6c,dr s1 s2ftgCodea4g6g 4H5H 0,2 0,4 0,4 Ref. 0,2 01,0h13 h13 02,005 MJ101 MJ101 16,3 14,7 11,0 24,8 19

26、 1,2 1,0 14 8 6,6 06 MJ121,25 MJ121,25 17,8 16,2 12,0 27,7 21 1,4 1,0 16 9 7,5 08 MJ141,5 MJ141,5 20,8 18,2 14,0 32,6 24 1,3 1,0 18 11 9,4 10 MJ161,5 MJ161,5 21,8 18,2 14,0 33,5 25 1,7 1,0 21 13 9,3 12 MJ181,5 MJ181,5 23,8 19,2 15,0 36,2 27 2,1 1,2 22 15 10,5 14 MJ201,5 MJ201,5 23,8 19,7 14,5 37,1 2

27、8 2,2 1,2 24 16 10,4 16 MJ221,5 MJ221,5 25,8 20,7 15,5 38,9 30 2,6 1,2 27 18 10,2 18 MJ241,5 MJ241,5 27,8 21,7 16,5 41,1 32 3,0 1,2 30 21 10,9 20 MJ271,5 MJ271,5 27,8 23,0 15,0 44,1 35 3,5 1,5 32 24 10,9 22 MJ301,5 MJ301,5 30,8 23,5 16,0 46,1 37 4,1 1,5 36 27 10,8 25 MJ331,5 MJ331,5 32,8 25,5 17,0 4

28、9,1 40 4,4 1,5 41 30 10,8 28 MJ361,5 MJ361,5 34,8 26,7 17,5 52,1 43 5,1 1,5 46 34 10,8 32 MJ391,5 MJ391,5 36,4 27,2 18,0 53,9 45 5,6 1,5 50 36 10,6 aCorresponds to the pipe nominal outside diameter. bAccording to ISO 5855-3. cThese dimensions are defined by the largest connection. dHorizontal drill

29、depth dimension = l1+ l6. eVertical drill depth dimension = l5. f Across flats. gOnly applicable when the diameter d2of EN 3273 is less than the actual forging diameter. Differences between these diameters are acceptable. 3.6 Mass According to Figure 2 and Table 2. EN 3080:2006 (E) 8 EXAMPLE 1 EN308

30、0-142205 aConnection 1 bConnection 2 cConnection 3 Figure 2 EXAMPLE 2 Connection 2 Connection 1 Connection 3 (is always the largest connection) EN3080-142205 : Code 22 + Code 14 + Code 05 119,7 g = 106,1 g + 8,5 g + 5,1 g a) First pick the mass for the largest connection out of the left part of tabl

31、e 2. b) Determine in the same line under code 14 the mass for connection 1 and under code 05 the mass for connection 3. c) Add the three values to receive the total coupling mass. EN 3080:2006 (E) 9 Table 2 Mass for connection 1 and 3 in grams Code 05 06 08 10 12 14 16 18 20 22 25 28 32 9,6 05 1,6 1

32、6,5 06 1,9 2,3 18,4 08 2,4 3,0 3,7 23,9 10 2,5 3,3 3,9 4,4 30,7 12 3,0 3,6 4,4 4,9 5,4 37,2 14 3,0 3,6 4,3 4,8 5,3 6,4 53,2 16 3,4 4,0 4,7 5,4 5,9 7,1 7,6 69,6 18 3,9 4,5 5,3 6,0 6,4 7,7 8,4 8,7 84,4 20 3,3 4,0 4,7 5,3 5,8 6,9 7,4 7,7 10,2 106,1 22 5,1 5,7 6,3 6,9 7,3 8,5 8,9 9,0 11,7 12,5 147,8 25

33、5,8 6,4 7,1 7,6 7,9 8,2 9,7 9,9 12,6 13,5 15,8 178,9 28 5,4 6,1 6,9 7,4 7,9 9,2 9,7 10,0 12,0 13,7 16,2 17,6 Mass for connection 2 ingrams 199,8 32 4,3 5,0 6,0 6,6 7,2 8,4 9,3 9,5 12,3 13,8 16,1 17,6 19,6EN 3080:2006 (E) 10 4 Designation EXAMPLE Description block Identity block TEE, REDUCED EN308014

34、 22 05 Number of this standard Code for connection 1 (see Table 1) Code for connection 2 (see Table 1) Code for connection 3 (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking According to EN 2424, style A and Figure 1. 6 T

35、echnical specification According to EN 3275, type II. blankBS EN 3080:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international le

36、vel. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be gra

37、teful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual up

38、dating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: o

39、rdersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides

40、a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44

41、(0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7

42、002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI a

43、lso holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, r

44、ecording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.