EN 2570-1996 en Aerospace Series - Nickel-Cadmium Batteries - Technical Specification《航空和航天系列 镍镉电池 交货技术条件》.pdf

《EN 2570-1996 en Aerospace Series - Nickel-Cadmium Batteries - Technical Specification《航空和航天系列 镍镉电池 交货技术条件》.pdf》由会员分享，可在线阅读，更多相关《EN 2570-1996 en Aerospace Series - Nickel-Cadmium Batteries - Technical Specification《航空和航天系列 镍镉电池 交货技术条件》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、BSI BS*EN*2570 76 m 1b24bb 05b70b1 591 W BRITISH STANDARD AEROSPACE SERIES Nickel-cadmium batteries - Technical specification * * rn The European standard EN 2570 : 1996 has the status of a British Standard ICs 29.220.30; 49.060 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

2、BS EN Z570 : 1996 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services ES1 BS*EN*2570 96 W Lb24bb 0569062 428 BS EN 2670 : 1996 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACW6, Ae

3、rospace batteries, upon which the following bodies were representid British Airways British Cable Maked Confederation British Rubber Manufacturers Association Civil Aviation Authority (Airworthiness Division) Federation of the Electronics Industry Mhistry of Defence Society of British Aerospace Comp

4、anies Ltd. This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standads Board and comes into effect on 15 November 1996 O BSI 1996 Amendments issued since publication I Date Amd No. The following BSI references rel

5、ate ta the work on this standard: committee reference ACW6 Draft for comment 92/83161 DC ISBN O 680 26324 X COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services- BSI BS*EN*2570 96 1624669 O569063 364 9 BS EN 2570 : 1996 Contents page Committees responsible Inside

6、 front cover Naona foreword ii Foreword 2 Text of EN 2570 3 i COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesBSI BS*EN*Z570 b W LbZ4bb 05b90b4 2TO = BS EN 2570 : 1996 National foreword This British standard has been prepared by Technical Committee ACW6 and i

7、s the English iangUage version of EN 2570 : 1996 Amspace series - Nickel-cadmium batteries - Technical specifiation published by the European Committee for Standardization (CEN). EN 2570 was produced as a result of inkrnational discussion in which the UNW Kingdom took an active part. Cross-reference

8、s Publication referred to IS0 7137 : 1992 LEC 51-1 : 1984 (EN 60051 : 1989) EC 952-1 : 1988 (EN 609521 : 1993) (EN 60952-2 : 1993) EN 3042 : 1991 IEC 952-2 : 1991 Corresponding British Standard BS 3G 229 : 1993 schedule for enzyimnmentai conditions and test procedures for airborne equipmmat BS 89 LX

9、rect acting indicating analogue electrical measuring instruments and their accessories Part 1 : 1990 Specifwation for - designed to : a) provide an emergency back-up and indirect starting of the main engines (normal batteries); b) provide instantaneous high power and direct starting (high-power or h

10、igh current batteries); c) satisfy new requirements (e.g. long service life). 4.1 Battery case The battery case shall be : - of metal or other material, resistant to corrosion and, unless otherwise specified, leakproof; - designed to hold 19 or 20 cells and such that any movement of the cells is avo

11、ided and that they can be removed. Where only 19 cells are required, a suitable dummy shall replace the twentieth cell. Seals and accessories shall be resistant to electrolyte (see 5.3.6) and to the temperatures (see 5.4.3 and 5.4.4). The case may be fitted in its upper section with air circulation

12、ducts. The arrangement and form of this device are described in the product standards. = 0,l CIA 0 e. g.: - 1) Current (A) = - Ci A f(h) 10 CiAh COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services- BSI BS*EN*Z570 96 1624669 0569069 882 Page 5 EN 2570 : 1996 4.2

13、The materials of the lid and its accessories shall have the same characteristics as those of the case. The lid may : Lid (of the battery case) - be provided with a seal and fitting devices, but is not necessarily sealed; - serve to secure the battery and/or have a separate attachment system. These o

14、ptions are described in the product standard. 4.3 Battery cells Cell Mwitdnem and lids They shall be : - made of insulating material which is resistant to the operating conditions; - joined together by a weld which is resistant to atmospheric pressure. Vent plugs Each cell shall be fitted with a ven

15、t plug in plastic material which is resistant to electrolyte and has a seal. The plug shall contain a device to permit the escape of gas and to prevent the escape of liquid if the battery is inverted. The vents shall open at an internal overpressure of between 14 kPa and 70 kPa. The vent plug shall

16、fulfil its function in all specified tests, at the pressures defined in 5.2.6.1. 4.4 Electrolyte Shall be an aqueous solution of potassium hydroxide. Purity of the solution shall conform to the battery manufacturers specifications. 4.5 Connections between cells These shall be in nickel-coated metal.

17、 The type of metal and the section of connections shall be selected so as to be able to withstand the maximum current which the battery can supply. The lock washers shall not damage the connections or the terminal nuts. Where internal monitoring devices are required, these shall not affect the batte

18、ry characteristics. 4.6 Identification of polarity The cells shall bear positive polarity markings (+I and if necessary negative (-1. The battery case shall also bear polarity markings : the positive pole of the receptacle shall be on the right, viewed from the outside. COPYRIGHT European Committee

19、for StandardizationLicensed by Information Handling ServicesPage 6 EN 2670 : 1996 B C DEFGH I J K L MNO min. *0,10 max. max. 9.93 17.02 38.91 9.53 1.27 3,18 1,57 18.51 1,70 14,68 16 23,22 3,58 4.7 Battery connector See figure 1 and table 1, figures 2 and 3 and table 2. P f 0,05 0,97 2,36 The locatio

20、n of the battery connector is defined in the product standards, in con,atmity wmr table 3. Dimensions and tolerances are in millimetres. B-B I+ Lockingpim a K Y- Figure l : Battery connector Table 1 Unless otherwise specified, tolerances are f 0,13 mm. I COPYRIGHT European Committee for Standardizat

21、ionLicensed by Information Handling Services BSI BS*EN*2570 96 m Lb24bb 05bL 430 m F f0,l Page 7 EN 2670 : 1996 0 H K L max. max. f 1,5 f 0,2 Battery 23 18 13 Figure 2 : Adaptor position for horizontal coupling 15,5 15 t- l- + Battery A-A 1 I Figure 3 : Adaptor position for vertical coupling Table 2

22、 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesBSI BS*EM*2570 96 Lb24bb9 05b9072 377 m Type of contact Type of connector See figure 1 Male See figures 2 and 3 Female Page 8 EN 2670 : 1996 Mounting Location Receptacle Battery Receptacle Battery 4.8 Electrica

23、l characteristics 4.8.1 Rated voltage 4.8.1.1 Of a cell 1,2 v The recommended number of cells for 28 V d.c. system is 20. 4.8.1.2 Of the battery 1,2 V multiplied by the number of cells connected in series. .4.8.2 Rated capacity It shall correspond to that indicated in the product standard. 5 Tests 5

24、.1 General The manufacturer shall supply all accompagning documents (see 8), approved in advance, which may be necessary for the performance and monitoring of tests. 5.1.1 lest conditions Unless otherwise indicated, these are as follows: - ambient temperature (23 i 5) OC; - pressure 85 kPa to 106 kP

25、a; - relative humidity 4 85 %. The batteries to be tested shall be in a vertical position, with or without a lid, depending on the type of test. Unless otherwise required, the vent plugs shall be fitted. The cells shall not be used outside the battery case. 5.1.2 Thermal stabilization Thermal stabil

26、ization is reached when a probe inserted between two centre cells reaches the required temperature, to f 1 K, for 1 h. All batteries heated or cooled in a test shall be left to rest, on open circuit, at the ambient temperature of the test station for at least 16 h. 5.1.2.1 High temperature tests 16

27、h to 24 h, at the specified temperature, without exceeding 12 h between charge and discharge. 5.1 -2.2 Low temperature tests 16 h to 24 h at the specified temperature. COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 9 EN 2670 : 1996 5.1.3 Connections Bat

28、teries shall be connected electrically using the appropriate connector. The battery voltage shall be measured at the connection points between the cable and the aircraft-side connector; the voltage drop in the connector shall be taken into account. Cables connected to connectors shall be of a suitab

29、le section so that in high temperature rapid discharge tests the temperature of the connector terminals remains lower than that of the internal battery connections. Connections between cells shall be tightened at the terminals to the torque (on the bolt or nut) specified by the manufacturer. 6.1.4 M

30、easuring equipment Electrical measuring equipment shall have an accuracy at least equivalent to category 0,s (see IEC 51-1), including shunts. Voltmeters shall have a resistance of at least 1 O00 RN and thermometers shall be accurate to less than 1 K. 5.1.5 Instructions - maintenance During the cour

31、se of tests, battwies shall undergo the necessary maintenance operations specified by the manufacturer. All operations, including reconditioning, shall be recorded in the test report. Examples : - the quantity of distilled water added shall be stated; - measurement of cell voltage variance between c

32、ells shall not be carried out unless signs of imbalance are detected at the end of discharge or during tests. Replacement of defective cells is not authorised during qualification tests. 5.1.6 Direct current charging method To ensure that qualification provides valid comparisons with regard to perfo

33、rmance. all charging cycles followed by measurement of capacity at the end of discharge shall be carried out using direct current (regulated to f I%), in accordance with the two phases shown below, the initial internal battery temperature being brought to (23 f 2) OC : - charge at a current of 1 CIA

34、 until the voltage corresponding to an average of 1,58 V per cell is reached at the battery terminals. Where only a charger set to 0,5 CIA is available, this phase shall be terminated at the mean voltage of 1,55 V per cell; - supplementary charge at a current of O,l CIA for 3 h ; when the test is no

35、t followed by measurement of electrical performance and when the amount of distilled water to be added is not specified, supplementary charge at 0,l CIA may be omitted, For some specific tests, diff erent charging conditions are specified in the appropriate clauses. Charging methods appropriate for

36、special batteries are described in their product standards. 5.1.7 Capacity measurement (controlled discharge) Unless otherwise indicated, leave the battery to rest on open circuit for 2 h to 4 h after the end of charge, and verify that it has returned to (23 f 2) OC. COPYRIGHT European Committee for

37、 StandardizationLicensed by Information Handling Services _ BSI BS*EN*2570 96 1624669 0569074 L4T Page 10 EN 2670 : 1996 5.1.7.1 Recharged capability The battery shall be discharged at a constant current of 1 CIA. Discharge shall be discontinued when the voltage at the battery terminals reaches the

38、value of the end discharge voltage : .e. 1 V per cell. The duration of this discharge shall be recorded. 5.1.7.2 Rated capacity To ensure that the rated capacity conforms to the product standard, a check shall be made that, under the conditions described in 5.1.7.1, at the end of 60 min the voltage

39、at the battery terminals is actually equal to or greater than the end discharge voltage. This measurement may be carried out during 5.1.7.1. 5.2 Mechanical tests 5.2.1 General examination 6.2.1.1 Visual inspection The following shall be checked : a) the presence, content and visibility of the identi

40、fication plate, see 7; b) that the presentation, finish, case colour and the terminal nut locking system conform to the definition documents; c) that the batteries comply with the requirements of 4; d) that the connector type conforms to that indicated in the product standard; e) that the terminal p

41、olarity markings, on the battery case and on the cells, are in the correct position; f) if required, during dismantling, 1) that the manufacturing codes or dates on the cells conform to those shown in the log book, 2) that the battery case and its coating, markings, seals and protective layer under

42、the lid are in good condition, 3) if the walls or lid of the case or the cell containers are deformed which shall be reported. 5.2.1.2 Surface appearance and amembly check The protective devices, the clean condition and removability of the vent plugs and of the connections from the terminals shall b

43、e checked. An inspection shall be made for any leakage through terminal seals or cell container welds. Any leakage of electrolyte shall result in removal of the cells for examination, even though scheduled “reconditioning“ operations are not yet due. During any dismantling operation, the internal in

44、sulators and cell containers shall be examined: they shall be smooth, with no rough areas, dents or deformations and shall not block the vent apertures. On reassembly during tests, the cells shall be returned to their initial position. 5.2.1 -3 Dimensions and mass These shall conform to the requirem

45、ents of the product standard. 5.2.2 Atting of connectors (see 4.7) The following are necessary for correct fitting of connectors to batteries : - satisfactory resistance of the battery to environmental and electrical tests; - conformity to the following requirements : COPYRIGHT European Committee fo

46、r StandardizationLicensed by Information Handling Services BSI BS*EN*2570 96 3624669 0569075 O86 W Page 11 EN 2670 : 1996 5.2.2.1 A part representing the aircraft-side connector (same locking ramps) shall be fitted in the connector, taking care that it does not short-circuit the two terminals. Conne

47、ctor according to figure 1 (receiving a free aircraft-side connector) 5.2.2.1.1 Rotation in the locking direction A rotation torque shall be applied progressively parallel to the mounting plane, to reach (8 f 1) N.m at the end of 10 s. 5.2.2.1.2 Traction along the loosening axis A force of (1 1 O0 f

48、 100) N shall be applied at a speed of approximately 1 O N/s and maintained for 1 O s. 5.2.2.2 Connector accordhg to Qwes 2 and 3 (with fande contacts on the batery skie) An intercell connection shall first be removed to avoid the risk of short circuit. Check : - the terminals of female contacts on

49、the external end of the connector; - the centre-to-centre distance between female contacts and their parallelism; - the tightening torque of the connector attachment nuts; - the existence of chamfers on the connector base plate; - the clearance between the axis of female contacts and the base plate. 5.2.2.3 Batteries without carrying handles With the battery in its normal position, an upward vertical force (in N) shall be exerted on the battery- side connector equal to 1,2 times the value of the battery mass. 5.2.2.4 Requirement8 The connections, batte