EN 13598-2-2016 en Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) polypropylene (PP) and polyethylene (PE) .pdf

《EN 13598-2-2016 en Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) polypropylene (PP) and polyethylene (PE) .pdf》由会员分享，可在线阅读，更多相关《EN 13598-2-2016 en Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) polypropylene (PP) and polyethylene (PE) .pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 13598-2:2016Plastics piping systems for non-pressure underground drainageand sewerage Unplasticizedpoly(vinyl chloride) (PVC-U), polypropylene (PP) andpolyethylene (PE)Part 2: Specifications for manholes andinspection chambersBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/

2、05/2013 15:06BS EN 13598-2:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13598-2:2016. It supersedes BS EN 13598-2:2009 which is withdrawn.BSI, as a member of CEN, is obliged to publish EN 13598-2:2016 as a British Standard. However, attention is drawn to

3、 the fact that during the development of this European Standard, the UK committee voted against its approval as a European Standard.There are a number of fundamental errors in this document which could a) have an effect on product performance and b) be a source of confusion when consideration is giv

4、en to products manufactured in accordance with part 1 of this standard. A revision is beingprepared by CEN / TC 155 to address these errors. EN 13598-1 is also being revised and will align with the corrected Part 2. The UK committee strongly recommend that products continue to be manufactured and sp

5、ecified to BS EN 13598-2:2009 until such a time as EN 13598-2 is amended and issued as a package with the updated EN 13598-1. The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for non-pressure applications.A list of organizations represented on th

6、is committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017ISBN 978 0 580 87586 1IC

7、S 93.030Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017.Amendments/corrigenda issued since publicationDate Text affectedBS EN 13598-2:2016EUROPEA

8、N STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13598-2 July 2016 ICS 93.030 Supersedes EN 13598-2:2009English Version Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specificati

9、ons for manholes and inspection chambers Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement enterrs sans pression - Poly(chlorure de vinyle) non plastifi (PVC-U), polypropylne (PP) et polythylne (PE) - Partie 2: Spcifications relatives aux regards et aux b

10、otes dinspection et de branchement Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 2: Anforderungen an Einsteigschchte und Kontrollschchte This European Standard was appro

11、ved by CEN on 12 May 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national sta

12、ndards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and

13、notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary

14、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC

15、Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13598-2:2016 EBS EN 13598-2:2016EN 13598-2:2016 (E) 2 Contents Page European foreword . 4 1 Scope 6 2 Normative references 6

16、3 Terms, definitions, and abbreviations 8 3.1 Terms and definitions . 8 3.2 Abbreviations 10 4 Material . 10 4.1 General . 10 4.2 Virgin material for bases 10 4.3 Virgin material for risers and cones 10 4.4 Utilisation of non-virgin materials . 11 4.5 Sealing rings 11 5 General characteristics 12 5.

17、1 General . 12 5.2 Colour . 12 6 Geometrical characteristics . 12 6.1 Dimensions 12 6.2 Additional requirements for Manhole Steps and fixed Ladders 12 7 Mechanical characteristics . 13 8 Physical characteristics . 15 9 Performance requirements 15 9.1 General performance . 15 9.2 Characterization of

18、rotationally moulded product submitted for performance testing . 17 10 Marking of inspection chambers and manholes and additional documentation . 17 10.1 Marking of inspection chamber bases and manhole bases 17 10.2 Marking of components other than bases . 18 10.3 Additional documentation . 18 Annex

19、 A (normative) Durability of materials used in specific base designs . 20 A.1 General . 20 A.2 Test procedure 20 A.3 Evaluation of data 20 A.4 Material characteristics . 20 Annex B (normative) Material requirements for materials used in specific shafts and cones . 22 Annex C (normative) Structural i

20、ntegrity of base . 24 BS EN 13598-2:2016 EN 13598-2:2016 (E) 3 C.1 General . 24 C.2 Test procedure 24 C.3 Evaluation of data 24 Annex D (normative) Impact test on manhole or chamber bases . 25 D.1 Test equipment . 25 D.2 Test procedure 25 Bibliography . 26 BS EN 13598-2:2016EN 13598-2:2016 (E) 4 Eur

21、opean foreword This document (EN 13598-2:2016) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical te

22、xt or by endorsement, at the latest by January 2017, and conflicting national standards shall be withdrawn at the latest by January 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respons

23、ible for identifying any or all such patent rights. This document supersedes EN 13598-2:2009. EN 13598-2:2016 includes the following significant technical changes with respect to EN 13598-2:2009: 1) Test methods have been updated to those of the latest EN ISO Standards;2) The confusion generated by

24、having different classes of chamber in Part 1 and Part 2 andtheir possible misuse because of this has been clarified. This will necessitate a revision ofthe current Part 1;3) The limiting clauses on the use of reclaim materials have been updated to help promote theuse of reclaim and recycles materia

25、ls.This European standard is a supplementary standard for System Standards for plastics piping systems of a particular material for a specified application. There are a number of such System Standards. System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pip

26、es, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organisation for Standardisation (ISO). They are supported by separate standards on test methods and by European Standards for thermoplastic underground drainage and sewerage systems, to which r

27、eferences are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. This European Standard consists of the following parts under the general title Plastics piping systems for non-pressu

28、re underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): Part 1: Specification for ancillary fittings including shallow inspection chambers Part 2: Specifications for manholes and inspection chambers (this standard) Part 3: Assessment

29、 of conformity (CEN/TS) BS EN 13598-2:2016 EN 13598-2:2016 (E) 5 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Est

30、onia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13598-2:2016EN 1

31、3598-2:2016 (E) 6 1 Scope This European Standard specifies the definitions and requirements for buried manholes and inspection chambers installed in non-pressure drainage and sewerage systems to a maximum depth of 6 m from ground level to the invert of the main chamber and manufactured from unplasti

32、cized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE). These products are intended for use in pedestrian or vehicular traffic areas and underground installations conforming to the general requirements given in EN 476 and are used out

33、side the building structure (application area code “U”). They are therefore marked accordingly with a “U”. Such products are also deemed to meet the requirements of EN 13598-1 for application area U without the need for further testing. These manholes and inspection chambers may also be used for sto

34、rm-water systems. This European Standard is only applicable to those chamber / manhole components (base, riser, cone telescopic part and other near surface components) where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete manhole or

35、 inspection chamber. This European standard only covers manholes and chambers with flow profile bases with or without sloping channels. It also covers the jointing of the component to the pipework system. The frame cover and grating components shall, unless otherwise specified, comply with EN 124-1,

36、 EN 124-2, EN 124-3, EN 124-4, EN 124-5 and EN 124-6 1 or EN 1253-42. The products covered by this European standard comprise the following: manholes constructed on a drain or sewer to permit entry by personnel. inspection chambers providing access to the drainage or sewerage system by means of insp

37、ection and cleaning equipment. NOTE 1 Shallow inspection chambers for use in non-roadway situations down to a depth of 1,25 m max are specified in EN 13598-1. The manhole and inspection chamber components can be manufactured by various methods e.g. injection moulding, rotational moulding, low-pressu

38、re moulding or fabricated from components made in accordance with other standards. NOTE 2 Both manholes and inspection chambers can be site assembled from different components, but can also be manufactured as a single unit. 2 Normative references The following referenced documents are indispensable

39、for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 476, General requirements for components used in drains and sewers EN 681-1, Elastomeric seals Mate

40、rials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric Seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 681-3, Elastomeric seals Materials requirement

41、s for pipe joint seals used in water and drainage applications Part 3: Cellular materials of vulcanized rubber BS EN 13598-2:2016 EN 13598-2:2016 (E) 7 EN 681-4, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 4: Cast polyurethane sealing el

42、ements EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) P

43、art 1: Specifications for pipes, fittings and the system EN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) Part 1: Specifications for pipes, fittings and the system EN 13101:2002, Steps for underground man entry chambers Requirements, marking, t

44、esting and evaluation of conformity EN 13476-1, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: General requirements and performance characteristi

45、cs EN 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for pipes and fittings with smooth internal and external surface and

46、 the system, Type A EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Specifications for pipes and fittings with smooth internal and pro

47、filed external surface and the system, Type B EN 13598-1:2010, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Specifications for ancillary fittings including shallow inspection ch

48、ambers EN 14396, Fixed ladders for manholes EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene with mineral modifiers (PP-MD) Part 1: Specifications for pipes, fittings and the system EN ISO 580:2005, Plastics piping and ducting systems Injection-mou

49、lded thermoplastics fittings Methods for visually assessing the effects of heating (ISO 580:2005) EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1) EN ISO 1133-1:2011, Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method (ISO 1133-1:2011) EN ISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersio