EN 1346-2007 9757 Adhesives for tiles - Determination of open time《瓷砖用粘合剂 敞露时间的测定》.pdf

《EN 1346-2007 9757 Adhesives for tiles - Determination of open time《瓷砖用粘合剂 敞露时间的测定》.pdf》由会员分享，可在线阅读，更多相关《EN 1346-2007 9757 Adhesives for tiles - Determination of open time《瓷砖用粘合剂 敞露时间的测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58T

2、he European Standard EN 1346:2007 has the status of a British StandardICS 83.180; 91.100.10Adhesives for tiles Determination of open timeBRITISH STANDARDBS EN 1346:2007BS EN 1346:2007Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIThis British Stand

3、ard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0 580 57396 5Amendments issued since publicationAmd. No. Date Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer

4、 immunity from legal obligations.National forewordThis British Standard is the UK implementation of EN 1346:2007. It supersedes BS EN 1346:1999 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/539, Ceramic tiles and other rigid tiling.A list of organi

5、zations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1346August 2007ICS 83.180; 91.100.10 Supersedes EN 1346:1996 English VersionAdhesives for

6、 tiles - Determination of open timeColles carrelage - Dtermination du temps ouvert Mrtel und Klebstoffe fr Fliesen und Platten - Bestimmungder offenen ZeitThis European Standard was approved by CEN on 21 January 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which sti

7、pulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard e

8、xists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards b

9、odies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUR

10、OPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1346:2007: ELicensed Copy: Wan

11、g Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIEN 1346:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Sampling.4 4 Test conditions 4 5 Test materials.4 5.1 General4 5.2 Ceramic tiles.5 5.3 Concrete slab .5 6 Apparatus .5 6.1 Notched trowel.5

12、 6.2 Weight .5 6.3 Pull-head plates .5 6.4 Test machine5 7 Mixing of adhesive.5 8 Procedure .6 9 Evaluation and expression of results6 10 Test report 7 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIEN 1346:2007 (E) 3 Foreword This document (EN 134

13、6:2007) has been prepared by Technical Committee CEN/TC 67 “Ceramic tiles”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting

14、national standards shall be withdrawn at the latest by February 2008. This document supersedes EN 1346:1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, C

15、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE

16、CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIEN 1346:2007 (E) 4 1 Scope This European Standard specifies the test method for the determination of the open time of ceramic tile adhesives. This European Standard is applicable to all ceramic tile adhesives for internal or external tile

17、installations on walls and floors. This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives can also be used for other types of tiles (natural and agglomerated stones etc.), if they do not advers

18、ely affect the stones. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN

19、196-1:2005, Methods of testing cement Part 1: Determination of strength EN 1067, Adhesives Examination and preparation of samples for testing EN 1323, Adhesives for tiles Concrete slabs for tests EN 12004, Adhesives for tiles Requirements, evaluation of conformity, classification and designation EN

20、14411, Ceramic tiles Definitions, classification, characteristics and marking EN ISO 15605, Adhesives Sampling (ISO 15605:2000) 3 Sampling Take a 2 kg sample of the adhesive in accordance with EN ISO 15605 and EN 1067. 4 Test conditions Standard conditions shall be (23 2) C and (50 5) % relative hum

21、idity and the air speed in the testing area less than 0,2 m/s. 5 Test materials 5.1 General Condition all test materials (adhesive etc.) for at least 24 h under standard conditions. The adhesive to be tested shall be within its shelf life, where this is specified. Licensed Copy: Wang Bin, ISO/EXCHAN

22、GE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIEN 1346:2007 (E) 5 5.2 Ceramic tiles The tiles shall be checked prior to conditioning to ensure that they are new, clean and dry. The tiles used for this method shall be of the following type: type P1: glazed porous body tile complying

23、with EN 14411, group BIII, of water absorption (15 3) % by mass, with a thickness in the range 7 mm to 10 mm and a profile back pattern less than 0,25 mm deep, cut to facial dimensions of (50 1) mm (50 1) mm. 5.3 Concrete slab The concrete slab shall comply with EN 1323. 6 Apparatus 6.1 Notched trow

24、el A notched trowel having 6 mm 6 mm notches at 12 mm centres. 6.2 Weight A mass capable of exerting a force of (20 0,05) N, with a cross-sectional area of less than 50 mm 50 mm. 6.3 Pull-head plates Square metallic plates, with dimensions of (50 1) mm (50 1) mm and a minimum thickness of 10 mm with

25、 a suitable fitting for connection to the test machine. 6.4 Test machine A test machine for direct pull tensile force test and with suitable capacity and sensitivity for the test. The machine shall be capable of applying the load to the pull-head plate at the rate of (250 50) N/s through a suitable

26、fitting that does not exert any bending force. 7 Mixing of adhesive The amount of water and/or liquid admix required for preparing the adhesive shall be as stated by the adhesive manufacturer in parts by mass, i.e. liquid to dry powder (if a range of values is given, the average shall be used). Prep

27、are a minimum quantity of 2 kg of the adhesive in a mixer of the type described in 4.4 of EN 196-1:2005, using the speed settings (140 5) r/min and (62 5) r/min planetary movement. Carry out the following procedure: pour the liquid into the pan; scatter the dry powder over the liquid; mix for 30 s;

28、take out the mixing paddle; Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIEN 1346:2007 (E) 6 scrape down the paddle and pan within 1 min; replace the paddle and mix for 1 min. Let the adhesive mature in accordance with the adhesive manufacturers i

29、nstructions and then mix for a further 15 s. In the case of ready-to-use dispersion adhesives or reaction resin adhesives, the manufacturers instructions shall be followed. 8 Procedure Apply a thin layer of the adhesive, mixed in accordance with Clause 7, to the concrete slab with a straight edge tr

30、owel. Then apply a thicker layer and comb with the notched trowel (6.1). Hold the trowel at an angle of approximately 60 to the substrate at a right angle to one edge of the slab and drawn across the slab parallel to that edge (in a straight line). After 5 min, 10 min, 20 min and 30 min place at lea

31、st ten test tiles of type P1, 50 mm apart, on the adhesive and load each tile with (20 0,05) N for 30 s. After 27 days storage under standard conditions, bond the pull-head plates (6.3) to the tiles with a suitable high strength adhesive (e.g. epoxide adhesive). After a further 24 h storage under st

32、andard conditions determine the tensile adhesion strength of the adhesive by applying a force increasing at a constant rate of (250 50) N/s. 9 Evaluation and expression of results The individual tensile adhesion strengths are quoted to the nearest 0,1 N/mm2using the following equation: As = L / A wh

33、ere As is the individual tensile adhesion strength in N/mm2; L is the total tensile load in N; A is the bonding area in mm2(2 500 mm2). The tensile adhesion strength for each time interval is determined as follows: determine the mean of the ten values; discard the values falling outside the range of

34、 20 % of the mean value; if five or more values remain, determine the new mean; if less than five values remain repeat the test; determine the mode of failure of the test units according to EN 12004 as the predominant mode. The open time in minutes, is the maximum time interval at which the adhesive

35、 meets the tensile adhesion strength requirement defined in EN 12004. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIEN 1346:2007 (E) 7 10 Test report The test report shall provide the following information: a) number and year of issue of this Euro

36、pean Standard, i.e. EN 1346:2007; b) place and date of sampling; c) type of adhesive, commercial designation and manufacturer; d) identification of test sample; e) handling and storage of samples before testing; f) test conditions; g) date of testing; h) amount of water or liquid used for preparing

37、the adhesive; i) test results (individual and mean values and the mode of failure); j) open time in minutes; k) any other factor that could have influenced the result. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSIBS EN BSILicensed Copy: Wang Bin,

38、 ISO/EXCHANGE CHINA STANDARDS, 28/02/2008 03:09, Uncontrolled Copy, (c) BSI389 Chiswick High RoadLondonW4 4AL1346:2007BSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internati

39、onal level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would

40、 be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an indivi

41、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. E

42、mail: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI pr

43、ovides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Te

44、l: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20

45、 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications

46、. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocop

47、ying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.