EN 13362-2018 en Geosynthetic barriers - Characteristics required for use in the construction of canals.pdf

《EN 13362-2018 en Geosynthetic barriers - Characteristics required for use in the construction of canals.pdf》由会员分享，可在线阅读，更多相关《EN 13362-2018 en Geosynthetic barriers - Characteristics required for use in the construction of canals.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Geosynthetic Barriers Characteristics required for use in the construction of canalsBS EN 13362:2018National forewordThis British Standard is the UK implementation of EN 13362:2018. It supersedes BS EN 13362:2013, which

2、 is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/553, Geosynthetics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. U

3、sers are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 93476 6ICS 91.100.50; 59.080.70Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the

4、 authority of the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 13362:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13362March 2018ICS 59.080.70; 91.100.50 Supersedes EN 13362:2013EUROPEAN COMMIT

5、TEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 13362:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersGeosynthetic Barrie

6、rs - Characteristics required for use in the construction of canalsGomembranes et gosynthtiques bentonitiques - Caractristiques requises pour lutilisation dans la construction des canauxGeosynthetische Dichtungsbahnen - Eigenschaften, die fr die Anwendung beim Bau von Kanlen erforderlich sindThis Eu

7、ropean Standard was approved by CEN on 23 October 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

8、concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member

9、 into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France

10、, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 13362:2018 (E)European foreword 4Introduction . 51 Scope . 62

11、 Normative references 63 Terms, definitions and abbreviations 93.1 Terms and definitions . 93.2 Abbreviations 104 Characteristics and corresponding methods of test .104.1 General 104.2 Types of application 104.2.1 General. 104.2.2 Application 1: “covered in service” .104.2.3 Application 2: “not cove

12、red in service” .114.3 Relevant characteristics . 124.4 Characteristics relevant to specific conditions of use 184.4.1 General. 184.4.2 Burst strength and elongation 184.4.3 Tear strength 184.4.4 Friction characteristics (direct shear and inclined plane tests) 184.4.5 Low temperature behaviour . 184

13、.4.6 Weathering .194.4.7 Chemical resistance 194.4.8 Resistance to wetting and drying .194.4.9 Freezethaw cycle resistance 194.4.10 Resistance to root penetration . 194.5 Release of dangerous substances . 195 Assessment and verification of constancy of performance (AVCP) 195.1 General 195.2 Type tes

14、ting 205.2.1 General. 205.2.2 Test samples, testing and compliance criteria 205.2.3 Test reports 215.2.4 Shared other party results 215.2.5 Cascading determination of the product type results 225.3 Factory production control (FPC) 235.3.1 General. 235.3.2 Requirements 235.3.3 Product specific requir

15、ements 275.3.4 Initial inspection of factory and of FPC .285.3.5 Continuous surveillance of FPC . 285.3.6 Procedure for modifications . 285.3.7 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity 28Annex A (normative) Durability of geosynthetic barr

16、iers 30Annex ZA (informative) Relationship of this European Standard with Regulation (EU) No. 305/2011 50Bibliography .533Contents PageBS EN 13362:2018EN 13362:2018 (E)European forewordThis document (EN 13362:2017) has been prepared by Technical Committee CEN/TC 189 “Geosynthetics”, the secretariat

17、of which is held by NBN.This document supersedes EN 13362:2013.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be withdrawn at the latest by Sep

18、tember 2019.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.This document has been prepared under a mandate given to CEN by the Europea

19、n Commission and the European Free Trade Association.For relationship with Regulation (EU) No 305/2011, see informative Annex ZA, which is an integral part of this document.The main changes with respect to the previous edition are listed below: the list of normative references has been updated; in 3

20、.1 three terms have been added; in 3.2 list of abbreviations has been updated; in 4.3, Table 1, has been modified to comply with the modified mandate M/386 (inclusion of elongation in separation and filtration functions) and has been technically revised, all H-coded characteristics have been replace

21、d by “A”, figures and keys have been revised; Clause 5 “Evaluation of conformity” has been superseded by new Clause 5 “Assessment and verification of constancy of performance (AVCP)” Annex A “Factory production control Factory production control scheme” has been deleted; former Annex B “Durability”

22、becomes Annex A, which has been totally revised; Annex ZA has been updated according to new template to fulfil requirements of CPR, also examples for CE-marking have been deleted.According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bo

23、und to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug

24、al, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.4BS EN 13362:2018EN 13362:2018 (E)IntroductionThis document allows manufacturers to describe geosynthetic barriers on the basis of declared values for characteristics relevant to the intended use and i

25、f tested to the specified method. It also includes procedures for assessment and verification of constancy of performance (AVCP) including the factory production control.This document can also be used by designers, end-users and other interested parties as a tool to define relevant and appropriate c

26、haracteristics for specifications. Tests for several non-mandated characteristics are still under study and will be included when the standard is revised.The term “product” used in this document refers to a geosynthetic barrier, including polymeric geosynthetic barriers, clay geosynthetic barriers a

27、nd bituminous geosynthetic barriers.This document is part of a group of standards, addressing the requirements for geosynthetic barriers when used in a specific application.Particular application cases can contain requirements about additional properties and - preferably standardized - test methods,

28、 if they are technically relevant and not conflicting with European Standards.The design life of the product should be determined, since its function may be temporary, as construction expediency, or permanent, for the lifetime of the structure.5BS EN 13362:2018EN 13362:2018 (E)1 ScopeThis European S

29、tandard specifies the characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, when used as fluid barriers and separation layer forwater, in the construction of canals and the appropriate test methods to det

30、ermine these characteristics.The intended use of these products is to control the leakage of the fluid through the construction.This document is not applicable to geotextiles or geotextile-related products, as defined in EN ISO 10318-1.This document provides for the assessment and verification of co

31、nstancy of performance (AVCP) of the product to this European Standard including factory production control procedures.This document defines characteristics to be considered with regard to the presentation of performance.This document does not cover applications where the geosynthetic barrier is to

32、be in contact with water that has been treated for human consumption.NOTE Where potable water is or can be in direct contact with the product, other relevant standards, requirements and/or regulations can be considered for the design.2 Normative referencesThe following documents, in whole or in part

33、, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 495-5:2013, Flexible sheets for waterproofing Det

34、ermination of foldability at low temperature Part 5: Plastic and rubber sheets for roof waterproofingEN 1109:2013, Flexible sheets for waterproofing Bitumen sheets for roof waterproofing Determination of flexibility at low temperatureEN 1296:2000, Flexible sheets for waterproofing Bitumen, plastic a

35、nd rubber sheets for roofing Method of artificial ageing by long term exposure to elevated temperatureEN 1849-1:1999, Flexible sheets for waterproofing Determination of thickness and mass per unit area Part 1: Bitumen sheets for roof waterproofingEN 1849-2:2009, Flexible sheets for waterproofing Det

36、ermination of thickness and mass per unit area Part 2: Plastic and rubber sheetsEN 12224:2000, Geotextiles and geotextile-related products Determination of the resistance to weatheringEN 12225:2000, Geotextiles and geotextile-related products Method for determining the microbiological resistance by

37、a soil burial testEN 12226:2012, Geosynthetics General tests for evaluation following durability testingEN 12310-1:1999, Flexible sheets for waterproofing Part 1: Bitumen sheets for waterproofing Determination of resistance to tearing (nail shank)EN 12311-1:1999, Flexible sheets for waterproofing Pa

38、rt 1: Bitumen sheets for roof waterproofing Determination of tensile propertiesEN 12311-2:2013, Flexible sheets for waterproofing Determination of tensile properties Part 2: Plastic and rubber sheets for roof waterproofing6 BS EN 13362:2018EN 13362:2018 (E)EN 13249:2016, Geotextiles and geotextile-r

39、elated products Characteristics required for use in the construction of roads and other trafficked areas (excluding railways and asphalt inclusion)EN 13250:2016, Geotextiles and geotextile-related products Characteristics required for use in the construction of railwaysEN 13251:2016, Geotextiles and

40、 geotextile-related products Characteristics required for use in earthworks, foundations and retaining structuresEN 13252:2016, Geotextiles and geotextile-related products Characteristics required for use in drainage systemsEN 13253:2016, Geotextiles and geotextile-related products Characteristics r

41、equired for use in erosion control works (coastal protection, bank revetments)EN 13254:2016, Geotextiles and geotextile-related products Characteristics required for the use in the construction of reservoirs and damsEN 13255:2016, Geotextiles and geotextile-related products Characteristics required

42、for use in the construction of canalsEN 13256:2016, Geotextiles and geotextile-related products Characteristics required for use in the construction of tunnels and underground structuresEN 13257:2016, Geotextiles and geotextile-related products Characteristics required for use in solid waste disposa

43、lsEN 13265:2016, Geotextiles and geotextile-related products Characteristics required for use in liquid waste containment projectsEN 14150:2006, Geosynthetic barriers Determination of permeability to liquidsEN 14151:2010, Geosynthetics Determination of burst strengthEN 14196:2016, Geosynthetics Test

44、 methods for measuring mass per unit area of clay geosynthetic barriersEN 14414:2015, Geosynthetics Screening test method for determining chemical resistance for landfill applicationsEN 14415:2004, Geosynthetic barriers Test method for determining the resistance to leachingCEN/TS 14416:2014, Geosynt

45、hetic barriers Test method for determining the resistance to rootsCEN/TS 14417:2014, Geosynthetic barriers Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriersCEN/TS 14418:2014, Geosynthetic Barriers Test method for the determi

46、nation of the influence of freezing-thawing cycles on the permeability of clay geosynthetic barriersEN 14575:2005, Geosynthetic barriers Screening test method for determining the resistance to oxidationEN 14576:2005, Geosynthetics Test method for determining the resistance of polymeric geosynthetic

47、barriers to environmental stress crackingEN 16416:2013, Geosynthetic clay barriers Determination of water flux index Flexible wall permeameter method at constant headEN ISO 527-1:2012, Plastics Determination of tensile properties Part 1: General principles (ISO 527-1:2012)EN ISO 527-3:1995, Plastics

48、 Determination of tensile properties Part 3: Test conditions for films and sheets (ISO 527-3:1995)7BS EN 13362:2018EN 13362:2018 (E)EN ISO 527-4:1995, Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997

49、)EN ISO 1133-1:2011, Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method (ISO 1133-1:2011)EN ISO 1183-1:2012, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)EN ISO 1183-2:2004, Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient