EN 1335-2-2009 en Office furniture - Office work chair - Part 2 Safety requirements《办公家具 办公椅 第2部分 安全性要求》.pdf

《EN 1335-2-2009 en Office furniture - Office work chair - Part 2 Safety requirements《办公家具 办公椅 第2部分 安全性要求》.pdf》由会员分享，可在线阅读，更多相关《EN 1335-2-2009 en Office furniture - Office work chair - Part 2 Safety requirements《办公家具 办公椅 第2部分 安全性要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN1335-2:2009ICS 13.180; 97.140NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDOffice furniture Office work chairPart 2: Safety requirementsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 April2009 BSI

2、2009ISBN 978 0 580 58648 4Amendments/corrigenda issued since publicationDate CommentsBS EN 1335-2:2009National forewordThis British Standard is the UK implementation of EN 1335-2:2009. Itsupersedes BS EN 1335-2:2000 which is withdrawn.The UK participation in its preparation was entrusted to Technica

3、lCommittee FW/0/3, Office.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cann

4、ot confer immunityfrom legal obligations.BS EN 1335-2:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1335-2April 2009ICS 97.140 Supersedes EN 1335-2:2000 English VersionOffice furniture - Office work chair - Part 2: Safety requirementsMobilier de bureau - Siges de travail de bureau - Partie 2

5、:Exigences de scuritBrombel - Bro-Arbeitsstuhl - Teil 2:SicherheitsanforderungenThis European Standard was approved by CEN on 28 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a nat

6、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in a

7、ny other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Esto

8、nia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCH

9、ES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1335-2:2009: EBS EN 1335-2:2009EN 1335-2:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative referen

10、ces 4 3 Terms and definitions .4 4 Safety requirements 4 4.1 General design requirements .4 4.1.1 Corners and edges, trapping, pinching and shearing .4 4.1.2 Adjusting devices 5 4.1.3 Connections .5 4.1.4 Avoidance of soiling 5 4.2 Test sequence 5 4.3 Stability during use6 4.4 Rolling resistance of

11、the unloaded chair 6 4.5 Strength and durability .6 5 Information for use 7 Annex A (normative) Loads, masses and cycles for safety tests 8 BS EN 1335-2:2009EN 1335-2:2009 (E) 3 Foreword This document (EN 1335-2:2009) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat o

12、f which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the

13、 possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1335-2:2000. This series consist of following parts: EN 1335-1, Office furniture Of

14、fice work chair Part 1: Dimensions Determination of dimensions; EN 1335-2, Office furniture Office work chair Part 2: Safety requirements; EN 1335-3, Office furniture Office work chair Part 3: Test methods. The main changes with respect to the previous edition are listed below: a) castor durability

15、(former 6.2) has been defined as functional test; b) foot rest stability and foot rest static load have been defined as safety test. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austr

16、ia, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 1335

17、-2:2009EN 1335-2:2009 (E) 4 1 Scope This part of EN 1335 specifies the mechanical safety requirements for office work chairs. The requirements are based upon use for 8 h a day by persons weighing up to 110 kg. For more severe conditions of use, increased requirements will be necessary. Annex A (norm

18、ative) includes loads, masses and cycles for safety tests. Additional loads, masses and cycles for functional tests can be found in EN 1335-3:2009, Annex C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only th

19、e edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1335-1:2000, Office furniture Office work chair Part 1: Dimensions Determination of dimensions EN 1335-3:2009, Office furniture Office work chair Part 3: Test methods

20、 EN 12529:1998, Castors and wheels Castors for furniture Castors for swivel chairs Requirements 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 castor assembly comprising a housing, one or more wheels, an axle and, if required, accessories EN

21、 12529:1998 4 Safety requirements 4.1 General design requirements 4.1.1 Corners and edges, trapping, pinching and shearing The chair shall be so designed as to minimise the risk of injury to the user. All parts of the chair with which the user comes into contact during intended use, shall be so desi

22、gned that physical injury and damage to property are avoided. These requirements are met when: a) the safety distance of accessible movable parts is either 8 mm or 25 mm in any position during movement; b) accessible corners are rounded with minimum 2 mm radius; BS EN 1335-2:2009EN 1335-2:2009 (E) 5

23、 c) the edges of the seat, back rest and arm rests which are in contact with the user when sitting in the chair are rounded with minimum 2 mm radius; d) the edges of handles are rounded with minimum 2 mm radius in the direction of the force applied; e) all other edges are free from burrs and rounded

24、 or chamfered; f) the ends of accessible hollow components are closed or capped. 4.1.2 Adjusting devices Movable and adjustable parts shall be designed so that injuries and inadvertent operation are avoided. It shall be possible to operate the adjusting devices from sitting position in the chair. 4.

25、1.3 Connections It shall not be possible for any load bearing part of the chair to come loose unintentionally. 4.1.4 Avoidance of soiling All parts which are lubricated to assist sliding (greasing, lubricating, etc.) shall be designed to protect users from lubricant stains when in normal use. 4.2 Te

26、st sequence The same chair shall be tested in the following sequence: a) stability tests (optional); b) rolling resistance test (optional); c) seat and back rest tests; d) foot rest static load test; e) arm rests durability test; f) arm rest downward static load test - central (see Table A.2, Footno

27、te a); g) stability tests; h) arm rest downward static load test - central (see Table A.2, Footnote b); i) rolling resistance test. BS EN 1335-2:2009EN 1335-2:2009 (E) 6 4.3 Stability during use The chair shall not overbalance under the following conditions: a) by pressing down on the front edge of

28、the seat surface in the most adverse position; b) by leaning out over the arm rests; c) by leaning against the back rest; d) by sitting on the front edge. Requirement a) is fulfilled if the chair does not overbalance when tested according to 7.1.1 of EN 1335-3:2009 with the forces and numbers of cyc

29、les according to Table A.1 of this standard. Requirements b) and d) are fulfilled if the chair does not overbalance when tested according to 7.1.2, 7.1.3, 7.1.4 and 7.1.5 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard. Requirement c) is fulfilled if t

30、he chair does not overbalance when tested according to 7.1.6 or 7.1.7 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.1 of this standard. 4.4 Rolling resistance of the unloaded chair The unloaded chair shall not roll unintentionally. This requirement is met when: a) the

31、castors are of identical construction; b) the rolling resistance is 12 N when tested according to EN 1335-3:2009, 7.4. 4.5 Strength and durability The chair shall be constructed to ensure that it does not create a risk of injury to the user of the chair under the following conditions: a) sitting on

32、the seat, both centrally and off-centre; b) moving forward, backwards, and sideways while sitting in the chair; c) leaning over the arm rests; d) pressing down on the arm rests while getting up from the chair. These requirements are fulfilled when after the tests specified in 7.2.1, 7.2.2, 7.2.6, 7.

33、3.1 and 7.3.2 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard: e) there are no fractures of any member, joint or component, and f) there is no loosening of joints intended to be rigid, and g) no major structural element is significantly deformed and th

34、e chair fulfils its functions after removal of the test loads and when: BS EN 1335-2:2009EN 1335-2:2009 (E) 7 h) after the test in 7.2.3 of EN 1335-3:2009 with the forces and numbers of cycles according to Table A.2 of this standard, the arm rests show no fracture. 5 Information for use Each chair s

35、hall be accompanied by information for use in the language of the country in which it will be delivered to the end user. It shall contain at least the following details: a) information regarding the intended use; b) information regarding possible adjustments and chair type (see EN 1335-1:2000); c) i

36、nstruction for operating the adjusting mechanisms; d) instruction for the care and maintenance of the chair; e) information regarding all adjustments; f) information for chairs with seat height adjustments with energy accumulators that only trained personnel may replace or repair seat height adjustm

37、ent components with energy accumulators; g) information on the choice of castors in relation to the floor surface. BS EN 1335-2:2009EN 1335-2:2009 (E) 8 Annex A (normative) Loads, masses and cycles for safety tests Table A.1 Loads, masses and cycles for stability tests Clauses given in EN 1335-3:200

38、9 Test Loads Cycle 7.1.1 Front edge overturning M127 kg 1 7.1.2 Forward overturning F1F2600 N 20 N 1 7.1.3 Forward overturning for chairs with foot rests F1 F21 100 N 20 N 1 7.1.4 Sideways overturning for chairs without arm rests F1F2600 N 20 N 1 7.1.5 Sideways overturning for chairs with arm rests

39、F1F2F3250 N 350 N 20 N 1 7.1.6 Rearwards overturning of chairs without back rest inclination F1F2600 N 192 N 1 7.1.7 Rearwards overturning of chairs with back rest inclination Number of discs: 13 1 BS EN 1335-2:2009EN 1335-2:2009 (E) 9 Table A.2 Loads and cycles for strength and durability tests Cla

40、uses given in EN 1335-3:2009 Test Loads Cycles 7.2.1 Seat front edge static load test F1 1 600 N 107.2.2 Combined seat and back static load test F1 F2 1 600 N 560 N 107.2.6 Foot rest static load test F 1 300 N 107.3.1 Seat and back durability Step 1 Loading Point A F 1 500 N 120 000Step 2 Loading Po

41、int C F 1 200 N 80 000Loading Point B F 320 N Step 3 Loading Point J F 1 200 N 20 000Loading Point E F 320 N Step 4 Loading Point F F 1 200 N 20 000Loading Point H F 320 N Step 5 Loading Point D and G (alternating) F 1 100 N 20 0007.3.2 Arm rest durability F 400 N 60 0007.2.3 Arm rest downward stati

42、c load test central F 750 N a 5F 900 Nb 5a This test shall be carried out before the stability tests b This test shall be carried out after the stability testsBS EN1335-2:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards

43、InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards sho

44、uld make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeer

45、esponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for al

46、l BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is

47、BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersServic

48、e. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial

49、discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyri