EN 10365-2017 en Hot rolled steel channels I and H sections - Dimensions and masses《热轧U型钢 I和H截面-尺寸和质量》.pdf

《EN 10365-2017 en Hot rolled steel channels I and H sections - Dimensions and masses《热轧U型钢 I和H截面-尺寸和质量》.pdf》由会员分享，可在线阅读，更多相关《EN 10365-2017 en Hot rolled steel channels I and H sections - Dimensions and masses《热轧U型钢 I和H截面-尺寸和质量》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 10365:2017Hot rolled steel channels, I andH sections Dimensions andmassesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 10365:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10365:2017. The UK participation in i

2、ts preparation was entrusted to TechnicalCommittee ISE/103, Structural Steels Other Than Reinforcements. A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users ar

3、e responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 89195 3 ICS 77.140.70 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of th

4、e Standards Policy and Strategy Committee on 31 January 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 10365:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10365 January 2017 ICS 77.140.70 English Version Hot rolled steel channels, I and H sections - D

5、imensions and masses Profils en U en aciers lamins chaud, poutrelles I et H - Dimensions et masses Warmgewalzter U-Profilstahl, I- und H-Trger - Mae und Masse This European Standard was approved by CEN on 14 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations whi

6、ch stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Eu

7、ropean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members

8、are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

9、Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any

10、 form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10365:2017 EBS EN 10365:2017EN 10365:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 5 4 Designation 5 5 Dimensions and masses 5 6 Tolerances on dimensions, sha

11、pe and mass . 7 7 Material . 7 Annex A (informative) Comparison of symbols used in this document with those in EN 1993-1-1 32 Bibliography . 33 BS EN 10365:2017EN 10365:2017 (E) 3 European foreword This document (EN 10365:2017) has been prepared by Technical Committee ECISS/TC 103 “Structural steels

12、 other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the lates

13、t by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This project was submitted to the Enquiry under reference prEN 16828. According to th

14、e CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, H

15、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10365:2017EN 10365:2017 (E) 4 1 Scope This European standard specifies the nominal dimen

16、sions and masses of the hot rolled steel channels, I and H sections. The following shapes are covered by this standard: Sections: Parallel flange I sections IPE; Wide flange beams HE; Extra wide flange beams HL and HLZ; Wide flange columns HD; Wide flange bearing piles HP and UBP; Universal beams UB

17、; Universal columns UC; Taper flange I sections IPN and J. Channels: Parallel flange channels UPE and PFC; Taper flange channels UPN, U and CH. These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel. 2 Normative references The following documents, in whol

18、e or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10024, Hot rolled taper flange I sec

19、tions - Tolerances on shape and dimensions EN 10025-1, Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels EN 10025-3, Hot rolled products

20、 of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4, Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels EN 10025

21、-5, Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance EN 10034, Structural steel I and H sections - Tolerances on shape and dimensions BS EN 10365:2017EN 10365:2017 (E) 5 EN 10079, Definition of steel

22、 products EN 10279, Hot rolled steel channels - Tolerances on shape, dimensions and mass 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079 apply. 4 Designation A section shall be designated according to Tables 1 to 15. This form of designation sha

23、ll be used in any enquiry and order. 5 Dimensions and masses Hot rolled steel channels, I and H sections complying with this European Standard shall be manufactured with the specified dimensions given in the Table 1 to 15 and according to Figures 1 to 4 below. Radii of fillets and toes of shape prof

24、iles vary with individual manufacturers and therefore are not specified. The masses per unit length specified in Tables 1 to 15 were calculated on the basis of a density of 7850 kg/m3. Figure 1 IPE, HE, HL, HD, HP, UBP, UB and UC parallel flange sections BS EN 10365:2017EN 10365:2017 (E) 6 Figure 2

25、Taper flange I sections IPN, J and extra wide flange beams HLZ Figure 3 Parallel flange channels UPE and PFC Figure 4 Taper flange channels UPN, U and CH BS EN 10365:2017EN 10365:2017 (E) 7 6 Tolerances on dimensions, shape and mass Tolerances on dimensions, shape and mass shall be as given in EN 10

26、034 for I (parallel flanges) and H sections. Tolerances on dimensions, shape and mass shall be as given in EN 10024 for taper flange I sections. Tolerances on dimensions, shape and mass shall be as given in EN 10279 for channels. Tolerances for shapes not included in the mentioned standards shall be

27、 as agreed upon between the manufacturer and the purchaser. 7 Material Sections and channels shall preferably be made from steel of a grade as specified in EN 10025-1, EN 10025-2, EN 10025-3, EN 10025-4 and EN 10025-5. Other steel grades as specified in EN 10225, EN 10028-2 and EN 10273 may also be

28、used for specific applications. The desired steel grade shall be specified at the time of ordering. BS EN 10365:2017EN 10365:2017 (E) 8 Table 1 Parallel flange I sections IPE Designation Dimensions G h b s t A kg/m mm mm mm mm cm2IPE AA 80 4,9 78,0 46,0 3,2 4,2 6,3 IPE A 80 5,0 78,0 46,0 3,3 4,2 6,4

29、 IPE 80 6,0 80,0 46,0 3,8 5,2 7,6 IPE AA 100 6,7 97,6 55,0 3,6 4,5 8,6 IPE A 100 6,9 98,0 55,0 3,6 4,7 8,8 IPE 100 8,1 100,0 55,0 4,1 5,7 10,3 IPE AA 120 8,4 117,0 64,0 3,8 4,8 10,7 IPE A 120 8,7 117,6 64,0 3,8 5,1 11,0 IPE 120 10,4 120,0 64,0 4,4 6,3 13,2 IPE AA 140 10,1 136,6 73,0 3,8 5,2 12,8 IPE

30、 A 140 10,5 137,4 73,0 3,8 5,6 13,4 IPE 140 12,9 140,0 73,0 4,7 6,9 16,4 IPE AA 160 12,3 156,4 82,0 4,0 5,6 15,7 IPE A 160 12,7 157,0 82,0 4,0 5,9 16,2 IPE 160 15,8 160,0 82,0 5,0 7,4 20,1 IPE AA 180 14,9 176,4 91,0 4,3 6,2 19,0 IPE A 180 15,4 177,0 91,0 4,3 6,5 19,6 IPE 180 18,8 180,0 91,0 5,3 8,0

31、23,9 IPE O 180 21,3 182,0 92,0 6,0 9,0 27,1 IPE AA 200 18,0 196,4 100,0 4,5 6,7 22,9 IPE A 200 18,4 197,0 100,0 4,5 7,0 23,5 IPE 200 22,4 200,0 100,0 5,6 8,5 28,5 IPE O 200 25,1 202,0 102,0 6,2 9,5 32,0 IPE AA 220 21,2 216,4 110,0 4,7 7,4 27,0 IPE A 220 22,2 217,0 110,0 5,0 7,7 28,3 IPE 220 26,2 220

32、,0 110,0 5,9 9,2 33,4 IPE O 220 29,4 222,0 112,0 6,6 10,2 37,4 IPE AA 240 24,9 236,4 120,0 4,8 8,0 31,7 IPE A 240 26,2 237,0 120,0 5,2 8,3 33,3 IPE 240 30,7 240,0 120,0 6,2 9,8 39,1 IPE O 240 34,3 242,0 122,0 7,0 10,8 43,7 BS EN 10365:2017EN 10365:2017 (E) 9 Designation Dimensions G h b s t A kg/m m

33、m mm mm mm cm2IPE A 270 30,7 267,0 135,0 5,5 8,7 39,2 IPE 270 36,1 270,0 135,0 6,6 10,2 45,9 IPE O 270 42,3 274,0 136,0 7,5 12,2 53,8 IPE A 300 36,5 297,0 150,0 6,1 9,2 46,5 IPE 300 42,2 300,0 150,0 7,1 10,7 53,8 IPE O 300 49,3 304,0 152,0 8,0 12,7 62,8 IPE A 330 43,0 327,0 160,0 6,5 10,0 54,7 IPE 3

34、30 49,1 330,0 160,0 7,5 11,5 62,6 IPE O 330 57,0 334,0 162,0 8,5 13,5 72,6 IPE A 360 50,2 357,6 170,0 6,6 11,5 64,0 IPE 360 57,1 360,0 170,0 8,0 12,7 72,7 IPE O 360 66,0 364,0 172,0 9,2 14,7 84,1 IPE A 400 57,4 397,0 180,0 7,0 12,0 73,1 IPE 400 66,3 400,0 180,0 8,6 13,5 84,5 IPE O 400 75,7 404,0 182

35、,0 9,7 15,5 96,4 IPE V 400 84,0 408,0 182,0 10,6 17,5 107,0 IPE A 450 67,2 447,0 190,0 7,6 13,1 85,6 IPE 450 77,6 450,0 190,0 9,4 14,6 98,8 IPE O 450 92,4 456,0 192,0 11,0 17,6 117,7 IPE V 450 107 460,0 194,0 12,4 19,6 132,0 IPE A 500 79,4 497,0 200,0 8,4 14,5 101,1 IPE 500 90,7 500,0 200,0 10,2 16,

36、0 115,5 IPE O 500 107 506,0 202,0 12,0 19,0 136,7 IPE V 500 129 514,0 204,0 14,2 23,0 164,1 IPE A 550 92,1 547,0 210,0 9,0 15,7 117,3 IPE 550 106 550,0 210,0 11,1 17,2 134,4 IPE O 550 123 556,0 212,0 12,7 20,2 156,1 IPE V 550 159 566,0 216,0 17,1 25,2 202,0 IPE A 600 108 597,0 220,0 9,8 17,5 137,0 I

37、PE 600 122 600,0 220,0 12,0 19,0 156,0 IPE O 600 154 610,0 224,0 15,0 24,0 196,8 IPE V 600 184 618,0 228,0 18,0 28,0 233,8 BS EN 10365:2017EN 10365:2017 (E) 10 Designation Dimensions G h b s t A kg/m mm mm mm mm cm2IPE 750 134 134 750,0 264,0 12,0 15,5 170,6 IPE 750 147 147 753,0 265,0 13,2 17,0 187

38、,5 IPE 750 173 173 762,0 267,0 14,4 21,6 221,3 IPE 750 196 196 770,0 268,0 15,6 25,4 250,8 BS EN 10365:2017EN 10365:2017 (E) 11 Table 2 Wide flange beams HE Designation Dimensions G h b s t A kg/m mm mm mm mm cm2HE 100 AA 12,2 91,0 100,0 4,2 5,5 15,6 HE 100 A 16,7 96,0 100,0 5,0 8,0 21,2 HE 100 B 20

39、,4 100,0 100,0 6,0 10,0 26,0 HE 100 C 30,9 110,0 103,0 9,0 15,0 39,3 HE 100 M 41,8 120,0 106,0 12,0 20,0 53,2 HE 120 AA 14,6 109,0 120,0 4,2 5,5 18,6 HE 120 A 19,9 114,0 120,0 5,0 8,0 25,3 HE 120 B 26,7 120,0 120,0 6,5 11,0 34,0 HE 120 C 39,2 130,0 123,0 9,5 16,0 49,9 HE 120 M 52,1 140,0 126,0 12,5

40、21,0 66,4 HE 140 AA 18,1 128,0 140,0 4,3 6,0 23,0 HE 140 A 24,7 133,0 140,0 5,5 8,5 31,4 HE 140 B 33,7 140,0 140,0 7,0 12,0 43,0 HE 140 C 48,2 150,0 143,0 10,0 17,0 61,5 HE 140 M 63,2 160,0 146,0 13,0 22,0 80,6 HE 160 AA 23,8 148,0 160,0 4,5 7,0 30,4 HE 160 A 30,4 152,0 160,0 6,0 9,0 38,8 HE 160 B 4

41、2,6 160,0 160,0 8,0 13,0 54,3 HE 160 C 59,2 170,0 163,0 11,0 18,0 75,4 HE 160 M 76,2 180,0 166,0 14,0 23,0 97,1 HE 180 AA 28,7 167,0 180,0 5,0 7,5 36,5 HE 180 A 35,5 171,0 180,0 6,0 9,5 45,3 HE 180 B 51,2 180,0 180,0 8,5 14,0 65,3 HE 180 C 69,8 190,0 183,0 11,5 19,0 89,0 HE 180 M 88,9 200,0 186,0 14

42、,5 24,0 113,3 HE 200 AA 34,6 186,0 200,0 5,5 8,0 44,1 HE 200 A 42,3 190,0 200,0 6,5 10,0 53,8 HE 200 B 61,3 200,0 200,0 9,0 15,0 78,1 HE 200 C 81,9 210,0 203,0 12,0 20,0 104,4 HE 200 M 103 220,0 206,0 15,0 25,0 131,3 HE 220 AA 40,4 205,0 220,0 6,0 8,5 51,5 BS EN 10365:2017EN 10365:2017 (E) 12 Design

43、ation Dimensions G h b s t A kg/m mm mm mm mm cm2HE 220 A 50,5 210,0 220,0 7,0 11,0 64,3 HE 220 B 71,5 220,0 220,0 9,5 16,0 91,0 HE 220 C 94,1 230,0 223,0 12,5 21,0 119,9 HE 220 M 117 240,0 226,0 15,5 26,0 149,4 BS EN 10365:2017EN 10365:2017 (E) 13 Designation Dimensions G h b s t A kg/m mm mm mm mm

44、 cm2HE 240 AA 47,4 224,0 240,0 6,5 9,0 60,4 HE 240 A 60,3 230,0 240,0 7,5 12,0 76,8 HE 240 B 83,2 240,0 240,0 10,0 17,0 106,0 HE 240 C 119 255,0 244,0 14,0 24,5 152,2 HE 240 M 157 270,0 248,0 18,0 32,0 199,6 HE 260 AA 54,1 244,0 260,0 6,5 9,5 69,0 HE 260 A 68,2 250,0 260,0 7,5 12,5 86,8 HE 260 B 93,

45、0 260,0 260,0 10,0 17,5 118,4 HE 260 C 132 275,0 264,0 14,0 25,0 168,4 HE 260 M 172 290,0 268,0 18,0 32,5 219,6 HE 280 AA 61,2 264,0 280,0 7,0 10,0 78,0 HE 280 A 76,4 270,0 280,0 8,0 13,0 97,3 HE 280 B 103 280,0 280,0 10,5 18,0 131,4 HE 280 C 145 295,0 284,0 14,5 25,5 185,2 HE 280 M 189 310,0 288,0

46、18,5 33,0 240,2 HE 300 AA 69,8 283,0 300,0 7,5 10,5 88,9 HE 300 A 88,3 290,0 300,0 8,5 14,0 112,5 HE 300 B 117 300,0 300,0 11,0 19,0 149,1 HE 300 C 177 320,0 305,0 16,0 29,0 225,1 HE 300 M 238 340,0 310,0 21,0 39,0 303,1 HE 320 AA 74,2 301,0 300,0 8,0 11,0 94,6 HE 320 A 97,6 310,0 300,0 9,0 15,5 124

47、,4 HE 320 B 127 320,0 300,0 11,5 20,5 161,3 HE 320 C 186 340,0 305,0 16,0 30,5 236,9 HE 320 M 245 359,0 309,0 21,0 40,0 312,0 HE 340 AA 78,9 320,0 300,0 8,5 11,5 100,5 HE 340 A 105 330,0 300,0 9,5 16,5 133,5 HE 340 B 134 340,0 300,0 12,0 21,5 170,9 HE 340 M 248 377,0 309,0 21,0 40,0 315,8 HE 360 AA

48、83,7 339,0 300,0 9,0 12,0 106,6 HE 360 A 112 350,0 300,0 10,0 17,5 142,8 HE 360 B 142 360,0 300,0 12,5 22,5 180,6 HE 360 M 250 395,0 308,0 21,0 40,0 318,8 BS EN 10365:2017EN 10365:2017 (E) 14 Designation Dimensions G h b s t A kg/m mm mm mm mm cm2HE 400 AA 92,4 378,0 300,0 9,5 13,0 117,7 HE 400 A 12

49、5 390,0 300,0 11,0 19,0 159,0 HE 400 B 155 400,0 300,0 13,5 24,0 197,8 HE 400 M 256 432,0 307,0 21,0 40,0 325,8 HE 450 AA 99,7 425,0 300,0 10,0 13,5 127,1 HE 450 A 140 440,0 300,0 11,5 21,0 178,0 HE 450 B 171 450,0 300,0 14,0 26,0 218,0 HE 450 M 263 478,0 307,0 21,0 40,0 335,4 HE 500 AA 107 472,0 300,0 10,5 14,0 136,9 HE 500 A 155 490,0 300,0 12,0 23,0 197,5 HE 500 B 187 500,0 300,0 14,5 28,0 238,6 HE 500 M 270 524,0 306,0 21,0 40,0 344,3 HE 550 AA 120 522,0 300,0 11,5 15,0 152,8 HE 550 A 166 540,0 300,0 12,5 24,0 211,8 H