DLA T-T-616 B-1986 TREATMENT MILDEW RESISTANT FOR ROPE AND CORD《绳索抗霉菌处理》.pdf

《DLA T-T-616 B-1986 TREATMENT MILDEW RESISTANT FOR ROPE AND CORD《绳索抗霉菌处理》.pdf》由会员分享，可在线阅读，更多相关《DLA T-T-616 B-1986 TREATMENT MILDEW RESISTANT FOR ROPE AND CORD《绳索抗霉菌处理》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、T-T-616BJune 22, 1986SUPERSEDINGT-T-616ASeptember 29, 1969FEDERAL SPECIFICATIONTREATMENT : MILDEW RESISTANT, FOR ROPE AND CORDIThis specification is approved by the Commissioner, Federal Supply Service,I General Services Administration, for the use of all Federal agencies.I 1. SCOPEI 1.1 q. This spe

2、cification covers one type of mildew-resistantI treatment of rope and cord.I 2. APPLICABLE DOCUMENTSI 2.1 Government publications.effect on date of invitation forthis specification to the extentI Federal Standard:The following documents, of the issues inbids or request for proposal, form a part ofsp

3、ecified herein.FED-STD-191 - Textile Test Methods.1 IIIIBeneficial comments (recommendations, additions, deletions) a“d a“ypertinent data which may be of use in improving tnis specification should beaddressed to: U.S. Army Natick Research, Development, and EngineeringCenter, Natick, MA 017605014 by

4、using the self-addressed StandardizationDocument Improvement Proposal (DD form 1426) appearing at the end of thisspecification or by letter.AMSC N/A FSC 4020DISTRIBUTION STATEMENT A. ApPrOved for public release; distrib”tio” isunlimited.Provided by IHSNot for ResaleNo reproduction or networking perm

5、itted without license from IHS-,-,-III T-T-616B(Activities outside the Federal Government may obtain copies of Federalspecifications, standards, and commercial item descriptions as outlined underGeneral Information in the Index of Federal Specifications, Standards andCommercial Item Descriptions. Th

6、e Index, which includes cumulative bimonthlysupplements as issued, is for sale on a subscription basis by theSuperintendent of Documents, U.S. Government Printing Office, Washington, D.c.20402.(Single copies of this specification, other Federal specifications,standards and commercial item descriptio

7、ns required by activities outside theFederal Government for bidding purposes are available without charge fromGeneral Services Administration Business Service Centers in Boston, MA; NewYork, NY; Washington, D.C.; Philadelphia, PA; Atlanta, GA; Chicago, IL; KansasCity, MO; Fort Worth, TX; Denver, CO;

8、 San Francisco, CA; Los Angeles, CA; a“dSeattle, WA.(Federal Government activities may obtain copies of Federal standardization,documents , and the Index of Federal Specifications, Standards and CommercialItem Descriptions from established distribution points in their agencies. )Military Standard:MI

9、L-STD-105 - Sampling Procedures and Tables for Inspection byAttributes.(Copies of Military specifications and standards required by contractors inconnection with sDecific procurement functions should be obtained from theprocuring activitj3. REQUIREMENTS3.1 Materials.or as directed by the contracting

10、 officer.)3.1.1 Rope and cord. The specification governing the rope and cord to betreated under this specification shall be cited in the applicable procurementdocument (see 6.2). Except as otherwise indicated herein, rope and cord shallconform to the requirements of the applicable specification for

11、the end itemprior to and after the mildew-resistant treatment.3.2 Treatment. The mildew inhibitor shall be copper-8-quinolinolate. Theuse of any other inhibitor is ,prohibited. Any petroleum fractions, oils orresins used shall be of the nonoxidizing type and shall be free of naphthenicacids or its s

12、alts. The inhibitor shall be thoroughly dispersed and soformulated that it may be applied to effect proper penetration into the ropeor cord.3.2.1 Application (hard and soft fiber ropes - manila, sisal, hemp, or. For hard and soft fiber ropes, other than cotton, the copper-8-quinolinolate shall be ap

13、plied to the fibers, yarns, or strands prior to2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T-T-616Btwisting (laying) into the finished rope. The treatment shall be uniformlyapplied throughout the entire cross section of the rope.3.2.1.1 Cotton r

14、opes and hard and soft fiber cords. The copper-8-quinolinolate shall be applied to the rope or cord as an after treatment. Thecopper-8-quinolinolate may be applied to the rope or cord with a water-repellent treatment, when required in the applicable end item specification.3.2.2 Concentration. The ap

15、plication of the inhibitor shall deposit withinthe rope or cord a minimum of O.13 percent to a maximum of 0.40 percent copperas metal from copper-8-quinolinolate when tested as specified in 4.2.4.3.2.3 Prohibited materials. The use of casein, glue, gum, starch, dextrin,water-soluble materials, paint

16、 dryers, resin or vegetable oils, oxidizing oilsur resin modified with such oils is prohibited except where required for usein polished finishes on cord.3.3 Color. Unless otherwise specified in the applicable end-itemspecification or procurement document, the color of the treated rope or cordshall b

17、e the natural color resulting from the treatment (see 6.3).3.4 Acidity (PH) after aging. The mildew-resistant treated rope or cordshall have a pH value of not less than 5.O before and after heat aging whentested as specified in 4.2.4.3.5 Breaking strength. A 10 percent loss in breaking strength, bas

18、ed onthe minimum specified for the untreated rope or cord, will be permitted, dueto the application of the treatment when tested as specified in 4.2.4.3.6 Handling characteristics. The inherent handling qualities of theuntreated ropes or cords shall not be altered by the application of themildew-res

19、istant treatment. The mildew-resistant treated finish on the ropesor cords shall not crack, peel, dust or flake from the treated surfaces.3.7 Workmanship. The treated rope or cord shall conform to the quality ofproduct established by this specification. The occurrence of defects shallnot exceed the

20、applicable acceptable quality levels.4. QUALITY ASSURANCE PROVISIONS.1 Responsibility for inspection. Unless otherwise specified i“ thecontract or purchase order, the contractor is responsible for the performanceof all inspection requirements as specified herein. Except as otherwisespecified in the

21、contract or purchase order, the contractor may use his ow” orany other facilities suitable for the performance of the inspectionrequirements specified herein, unless disapproved by the Government. TheGovernment reserves the right to perform any of the inspections set forth inthe specification where

22、such inspections are deemed necessary to assure thatsupplies and services conform to prescribed requirements.3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T-T-616B4.1.1 Responsibility for compliance. All items must meet all requirementsof sections

23、 3 and 5. The inspection set forth in this specification shallbecome a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specificationshall not relieve the contractor of the responsibility of assuring that allproducts or supplies

24、submitted to the Government for acceptance comply withI all requirements of the contract. Sampling in quality conformance does notauthorize submission of known defective material, either indicated or actual,nor does it commit the Government to acceptance of defective material.II4.1.2 Certificate of

25、compliance. Where certificates of compliance aresubmitted, the Government reserves the right to check test such items toIdetermine the validity of the certification.4.2 Quality conformance inspection. Unless otherwise specified, samplingI for inspection shall be performed in accordance with MIL-STD-

26、105.4.2.1 Component and materia I inspection. In accordance with 4.1,Icomponents and materials shall be inspected in accordance with all therequirements of referenced specifications, drawings, and standards unlessotherwise excluded, amended, modified, or qualified in this specification orIapplicable

27、 purchase document.4.2.2 End item visual examination. The end item shall be examined inaccordance with the applicable classification of defects for the untreatedmaterial and as listed-in table I. In the event that a condition listed intable I represents a duplication of a condition cited in another

28、applicabledocument, the condition shall be counted only once. The defects listed intable I shall be counted regardless of their proximity to each other. Thesample unit for this examination shall be one packaged unit of rope or cord.Ten percent of the length contained in each sample unit, but not les

29、s than 100feet, shall be subjected to the visual examination. The lot size for thisexamination shall be expressed in packaged units of rope or cord. Theinspection level shall be level I and the acceptable quality level (AQL),expressed in terms of defects per hundred units, shall be 1.5 for majordefe

30、cts and 4.0 for total (major and minor combined) defects.I TABLE 1. End item visual defectsI Examine Defects Classification14aJor _MinorAppearance and Cut (any) xworkmanship Chafed or damaged xFinish other than specified xFinish cracked, peeled, dusted,or flaked x1LumPs xI 4I Provided by IHS Not for

31、 ResaleNo reproduction or networking permitted without license from IHS-,-,-T-T-616BTABLE 1. End item visual defects (centd)MaJq MinorCleanness Spot or stain clearly visible / xOverall uncleanliness xColor Other than natural (unless otherwisespecified) xSpecific shade specified not withinestablished

32、 tolerances x1 At normal inspection distance (approximately 3 feet).4.2.3 Examination for weight or lenth and windin. These examinationsshall be conducted in accordance with the provisions of the applicablespecification for the untreated material or as specified in the contract ororder.4.2.4 End ite

33、m testing. The methods of testing specified inFED-STD-191, wherever applicable and as listed in the table 111, shall befollowed. When the “Number of determinations” and “Results reported as” arenot specified in table III, they shall be as required by the referenced testmethod. The physical and chemi

34、cal values specified in section 3 apply to theaverage of the determinations made on a sample unit for test purposes asspecified in the applicable test methods. The sample size shall be inaccordance with table II. The sample unit for testing shall be one packagedunit of rope or cord. The lot size sha

35、ll be expressed in packaged units ofrope or cord. All test reports shall contain the individual values utilizedin expressing the final result. The lot shall be unacceptable if one or moresample units fail to meet any requirement. Tests to determine compliance withspecification requirements, includin

36、g quantity of delivery, may be made underprevailing atmospheric conditions, except in settlement of dispute in whichcase the test should be made upon material which has reached equilibrium understandard conditions as defined in FED-STD-191 .TABLE II. Sampling for testsLot size (No. of packaged units

37、 of rope or cord) Sample size (sample units)800 or less 2801 up to and including 22,000 322,001 and over 55Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T-T-616BTABLE III. End item testsNumber of deter-minations perRequirement Test individual Resul

38、tsCharacteristic paragraph method sample unit reported asTreatment:Inhibitor andcompoundspresent 3.2 / g/Application to:Hard and softfiber ropes 3.2.1 /Cotton ropes andhard and softfiber cords 3.2.1.1 1Cross-sectionaluniformity 3.2.1 Visual 1 Pass or failConcentration ofcopper-8-quinolinolate(percen

39、t copper) 3.2.2 2050Prohibitedmaterials 3.2.3 /Acidity (PH)after aging 3.4 4.2.4.1 2Breaking strength 3.5 1 1 Reported tothe nearestO.1 percent“Unless otherwise specified, a certificate of compliance shall besubmitted and will be acceptable for the stated requirement. ”The certificate of compliance

40、for the requirements as specified in 3.2shaLl incorporate a statement that specific inhibitor (copper-8-quinolinolate) was used in the treatment of the rope or cord and that anypetroleum fractions, oils or resins used are of the nonoxidizing type andare free of naphthenic acid or its salts.Breaking

41、strength shall be determined in conformance with the a75ethodspecified in the applicable specification for the untreated material.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-T-T-616B4.2.4.I Acidity (PH) before and after heat aging.a. The pH of th

42、e mildew resistant treated rope, yarns or cord shall betested prior to aging in accordance with method 2811b. pH after agin&. Samples (approximately 10weighing bottles (uncovered at a temperature of 1750At the end of this period the yarns or cord shall bein accordance with method 2811 of FED-STD-191

43、.5.6.6.1ropes6.2PACIUGING. (Not applicable).NOTESIntended use. The mildew-resistant treatmentor cords.of FEDSTD-191.grams) shall be put into 180F for 44 hours.tested for acidity (pH)is intended for use withOrdering data. Purchasers should select the preferred optionspermitted herein and include the

44、following information in procurementdocuments :a. Title, number, and date of this specification.b. Title, number, and date of specification governing the untreatedrope or cord.c. Color, if other than required (see 3.3 and 6.3).6.3 Standard sample. If a specific shade (color) is specified andreferenc

45、e is made to a standard sample, for access to that standard sampleaddress the procuring office issuing the invitation for bids.MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITIES:Custodians: GSA-FSSFPIArmy - GLNavy - AS PREPARING ACTIVITY :Air Force - 99Army - GLReview activities:Project No. 40

46、20-0284Navy - MCAir Force - 82DLA - ESUser activitv:Army - MI!7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-=ANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALtie Instructions - Rfvc?ic Side)DOCUMENT NU8ABEFI 2T&NTTT ITLE7-T-616B : MILDEW RESISTANT, FOR

47、ROPE AND CORD.NAME 0FSU0k41l NOORGANl ZAT10N 4.TYPEOFORGANIZATION(M-h0“,)a75VENLIORa75 us,.AOORE.SSml,CIW.Etit,ZIP C+)(-J MA!JIJFACT”IIERa75 O,”EFI,pc,fi,PROOLEM AmEASa PUWWMI N“mt,r a71nd WW61” O:b. R9c0m W.a.dlnwc. _/R.il.nsl. for Rocomnu.dmion:mEMA13KSk NAME OF SU0M1TTE14 fhc Pht Ml) - OmlonU b.

48、WORK TELEPHONE NUMBER (1”. #u&A”.Co&) - Optic”.1MAILING ADDRESS (LWIW.L CIIY. Sti”. ZIP Co&l - ODtlOnd e OATE OF sunw5sIoN ,YytdmnojQDJOJ&i1426 PilEvlOUS EDITION IS0850LE7ENAT IC.KOP-I. Feh R6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IIIIII,INS

49、TRUCTIONS: In . amtinuing effort to nuke ourstandardizstion docum.nt$ bettsr, tbe DoD pro?ides khh form for w i“submiitins commsnta sod suggestions for impnwementa, All usem of mifitary dnrdization documenu SIC invited prowideSUSSutiom. lM form UISY bs detsched, folded stons tbe Iina indicated, treed afong tbt lG.XC edge (DO NOT STAP